Experimental and computational evaluation of cyclic solvent injection in fractured tight hydrocarbon reservoirs.
Ontology highlight
ABSTRACT:
SUBMITTER: Ghanizadeh A
PROVIDER: S-EPMC8097080 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Gas flooding and foam flooding are potential technologies for tertiary oil recovery in fractured-vuggy reservoirs. The development and mechanism research of fractured-vuggy reservoirs is difficult due to the complex structures and the strong heterogeneity of fractured-vuggy reservoirs. Visualization simulation is one of the effective methods to study the flow behavior of fluid in fractured-vuggy reservoirs. In this study, an upscaling method of visualization simulation from one dimension (1D) to three dimensions (3D) was established, and the physical models of fractured-vuggy reservoirs were designed and fabricated. Water flooding, gas flooding, and gel foam flooding were carried out in the models. The experimental results showed that gas flooding has a single flow channel and water flooding has multiple flow channels in fractures and vugs. Gel foam with an excellent capability of mobility control and a high microscopic displacement efficiency swept in all directions at a uniform velocity. The EOR mechanisms of gel foam in fractured-vuggy reservoirs were mainly as follows: reducing interfacial tension, increasing mobility ratio, selectively plugging high permeability channels, and discontinuous flow. In the displacement process of fractured-vuggy reservoirs, water should be injected from the well at the bottom of the reservoir, and gas should be injected from the well located in the vug at the high part of the reservoir. Gel foam with strong stability and high viscosity should be selected and injected in most kinds of injection wells in fractured-vuggy reservoirs. This study provides a complete method of visualization simulation for the study of flow behavior in fractured-vuggy reservoirs and provides theoretical support for the application of gas flooding and gel foam flooding in fractured-vuggy reservoirs.
| S-EPMC10530889 | biostudies-literature
Project description:A fundamental knowledge of microbial community structure in petroleum reservoirs can improve predictive modeling of these environments. We used hydrocarbon profiles, stable isotopes, and high-density DNA microarray analysis to characterize microbial communities in produced water from four Alaskan North Slope hydrocarbon reservoirs. Produced fluids from Schrader Bluff (24-27°C), Kuparuk (47-70°C), Sag River (80°C), and Ivishak (80-83°C) reservoirs were collected, with paired soured/non-soured wells sampled from Kuparuk and Ivishak. Chemical and stable isotope data suggested Schrader Bluff had substantial biogenic methane, whereas methane was mostly thermogenic in deeper reservoirs. Acetoclastic methanogens (Methanosaeta) were most prominent in Schrader Bluff samples, and the combined ?D and ?(13)C values of methane also indicated acetoclastic methanogenesis could be a primary route for biogenic methane. Conversely, hydrogenotrophic methanogens (e.g., Methanobacteriaceae) and sulfide-producing Archaeoglobus and Thermococcus were more prominent in Kuparuk samples. Sulfide-producing microbes were detected in all reservoirs, uncoupled from souring status (e.g., the non-soured Kuparuk samples had higher relative abundances of many sulfate-reducers compared to the soured sample, suggesting sulfate-reducers may be living fermentatively/syntrophically when sulfate is limited). Sulfate abundance via long-term seawater injection resulted in greater relative abundances of Desulfonauticus, Desulfomicrobium, and Desulfuromonas in the soured Ivishak well compared to the non-soured well. In the non-soured Ivishak sample, several taxa affiliated with Thermoanaerobacter and Halomonas predominated. Archaea were not detected in the deepest reservoirs. Functional group taxa differed in relative abundance among reservoirs, likely reflecting differing thermal and/or geochemical influences.
| S-EPMC4124708 | biostudies-literature
Project description:Characterization of heterogeneous reservoirs such as multilayered or fractured systems is an important issue in different disciplines such as hydrology, petroleum and geothermal systems. One of the popular methods that can be used for this purpose is tracer tests. Better understanding of the mechanisms of mass transfer (convection-diffusion process) is essential for having a proper test interpretation. In this study, the solutions of different scenarios of tracer flow in a pair of high and low-permeable layered reservoirs including convection and diffusion mechanisms are discussed. Although analytical solutions generally provided exact solutions, they involve several assumptions and might be hard to use for complex problems. As a result, numerical methods are selected for the investigation of different scenarios and addressing cases that are beyond access of analytical methods. In this study, several scenarios of considering diffusion and convection in low and high permeable zones and effective parameters on tracer concentration are investigated. According to the results of this study, the higher the porosity ratio of low to high permeable layer, the more time is needed to get the final concentration value. Also, by increasing the value of the dispersivity coefficient, the time needed to increase the concentration decreases. In other words, the sharp increase in concentration for lower times is seen in higher dispersivity values. The concentration profile variation is affected by Peclet number. The difference among concentration profiles in different cases is considerable, especially in low Peclet numbers where the diffusion mechanism is dominant. This behavior is more common in low permeable mediums such as multilayered tight or shale reservoirs.
| S-EPMC10495337 | biostudies-literature
Project description:In-depth profile control is a great challenge for high-efficiency oil displacement by water flooding. In this work, a shear-responsive self-lubricating hydrogel FPP-0.5, by combining the thixotropic FT (N-fluorenylmethoxycarbonyl-l-tryptophan) supramolecular network with high-strength PAM-PAANa (PAM: polyacrylamide, PAANa: sodium polyacrylate) polymer network, was synthesized and applied for in-depth profile control in water flooding. The disassembly of the FT supramolecular network induced by shear force, accompanied by the formation of a lubricating layer on the gel surface, gives FPP-0.5 gel self-lubricating function. Meanwhile, the PAM-PAANa polymer network, as a protective scaffold for the FT network, endows FPP-0.5 with high strength, making it difficult to be broken by water flow. Moreover, the shear responsiveness enables FPP-0.5 to adjust its own strength and self-lubricating performance according to the different stages of the profile control process, so as to realize dynamic profile control. From oil displacement results, in comparison to the PAM-PAANa gel, the plugging rate, water flooding volume sweep efficiency, and oil recovery of FPP-0.5 were improved by 83.1, 155.4, and 34.0%, respectively, up to 86.6, 83.5, and 71.3%, indicating its better in-depth profile control ability.
| S-EPMC7143440 | biostudies-literature
Project description:In the past few decades, scholars have made great breakthroughs in the study of well test analysis of carbonate rock. The previous studies are based on horizontal wells, straight wells, fractured wells, and inclined wells. With the development of fracturing technology, acid fracturing technology is considered to be the most effective measure to develop carbonate reservoirs. As the carbonate rock is easily dissolved in carbonic acid, multi-branched fractures will be produced near a vertical well. This article presented a semi-analytical model for multi-branched fractures in naturally fractured-vuggy reservoirs for the first time, which laid a theoretical foundation for solving well test analysis for finite conductivity multi-branched fractures. The model can quantify the wellbore flow pressure and applied to obtain more parameters reflecting comprehensive flow characteristics through using history matching procedure. The results were compared with numerical simulation and the existing analytical solutions of a single fracture model. Then in this paper, flow characteristics are recognized and there are five flow regimes found in the type curves, e.g. bi-linear flow region, linear flow region, inter-porosity flow region between vugs and fractures, inter-porosity region between matrix and fractures, and radial flow region. Finally, the influence factors analysis shows fracture number will mainly affect flow behavior of bi-linear flow and linear flow. The angle analysis showed that as the fractures were closer, their interaction became stronger. The conductivity would seriously affect the flow behavior in the early time. Linear flow cannot be observed when the conductivity is less than 1 and bi-linear flow cannot be observed when the conductivity is more than 20. And the effect of fracture length on flow behavior occurs in the early time. Bi-linear flow and linear flow characteristics cannot be observed when the fracture length is reduced.
| S-EPMC6072746 | biostudies-literature
Project description:In subsurface biodegraded oil reservoirs, methanogenic biodegradation of crude oil is a common process. This process was previously assigned to the syntrophy of hydrocarbon-degrading bacteria and methanogenic archaea. Recent studies showed that archaea of the Candidatus Methanoliparum named as alkylotrophic methanogens couple hydrocarbon degradation and methane production in a single archaeon. To assess the geochemical role of Ca. Methanoliparum, we analyzed the chemical and microbial composition and metabolites of 209 samples from 15 subsurface oil reservoirs across China. Gas chromatography-mass spectrometry analysis revealed that 92% of the tested samples were substantially degraded. Molecular analysis showed that 85% of the tested samples contained Ca. Methanoliparum, and 52% of the tested samples harbored multiple alkyl-coenzyme M derivatives, the intercellular metabolites of alkylotrophic archaea. According to metagenomic and metatranscriptomic analyses, Ca. Methanoliparum dominates hydrocarbon degradation in biodegraded samples from the Changqing, Jiangsu, and Shengli (SL) oilfields, and it is persistently present as shown in a 15-year-long sampling effort at the Shengli oilfield. Together, these findings demonstrate that Ca. Methanoliparum is a widely distributed oil degrader in reservoirs of China, suggesting that alkylotrophic methanogenesis by archaea plays a key role in the alteration of oil reservoirs, thereby expanding our understanding of biogeochemical process in the deep biosphere.
| S-EPMC11376074 | biostudies-literature
Project description:The development of tight oil has started relatively late, and the flow mechanisms and fluid movability are still research spotlights. The goal of this paper is to investigate the percolation characteristics and fluid movability of the Chang 6 tight sandstone oil layer in the Upper Triassic Yanchang Formation, Ordos Basin, China. Results show that (1) at low flow velocity, the percolation curve of flow velocity vs pressure gradient is a concave-up nonlinear curve and does not pass through the origin. It is more difficult for oil flow than water flow in cores with similar permeability due to rock wettability and fluid apparent mobility. The application of back pressure makes the nonlinear stage eliminated and the percolation character improved. (2) Two-phase flow tests reveal that oil-phase permeability decreases faster in samples with lower permeability, and the coexistent flow region of oil and water is relatively narrow. The contribution of oil recovery mainly happens at the early stage. The permeability at the isotonic point reduces with the decrease of sample permeability. (3) Flow during water flooding can be roughly divided into four stages according to the injection pressure and flow change. The injection pressure experiences stages of increasing to a peak, then decreasing, and finally becoming stable, accompanied by an increase of oil production until water breaks through. (4) The pore throats of the target reservoir mainly range from 0.001 to 10 ?m, and the bound water mainly distributes in pores less than 0.2 ?m. The irreducible water saturation is 30-35%, and the movable fluid saturation is 65-70%, mainly distributed in pores at 0.2-10.0 ?m with a maximum of 2.0 ?m. The results will supplement the existing knowledge of percolation characters and fluid movability in tight sandstone oil reservoirs.
| S-EPMC7315431 | biostudies-literature
Project description:Deep eutectic solvents (DESs) are green solvents developed as an alternative to conventional organic solvents and ionic liquids to extract nitrogen compounds from fuel oil. DESs based on p-toluenesulfonic acid (PTSA) are a new solvent class still under investigation for extraction/separation. This study investigated a new DES formed from a combination of tetrabutylphosphonium bromide (TBPBr) and PTSA at a 1:1 molar ratio. Two sets of ternary liquid-liquid equilibrium experiments were performed with different feed concentrations of nitrogen compounds ranging up to 20 mol% in gasoline and diesel model fuel oils. More than 99% of quinoline was extracted from heptane and pentadecane using the DES, leaving the minutest amount of the contaminant. Selectivity was up to 11,000 for the heptane system and up to 24,000 for the pentadecane system at room temperature. The raffinate phase's proton nuclear magnetic resonance (1H-NMR) spectroscopy and GC analysis identified a significantly small amount of quinoline. The selectivity toward quinoline was significantly high at low solute concentrations. The root-mean-square deviation between experimental data and the non-random two-liquid (NRTL) model was 1.12% and 0.31% with heptane and pentadecane, respectively. The results showed that the TBPBr/PTSADES is considerably efficient in eliminating nitrogen compounds from fuel oil.
| S-EPMC7662348 | biostudies-literature
Project description:Carbon dioxide (CO2) is both a primary greenhouse gas and a readily available energy source. In this study, a new underground coal permeability enhancement technique utilizing cryogenic liquid CO2 (L-CO2) cyclic injection is proposed. The key parameters that determine the feasibility of this technique are cycle period and cycle number within a fixed working period. The optimal value of these two parameters mainly depends on the pore structure evolution law of coal cores before and after cryogenic L-CO2 cyclic freeze-thaw. Accordingly, nuclear magnetic resonance (NMR) was employed to study the evolution characteristics of the fracture networks and pore structures in coal cores subjected to different freeze-thaw cyclic modes. The results demonstrated that the amplitude and width of all peaks of the T2 spectra of the three coal cores (lignite, gas coal, and 1/3 coking coal) increased with an increase in the number of injection cycles. Additionally, as the number of freeze-thaw cycles (Nc) increased, the total porosity and effective porosity of the coal cores increased linearly before stabilizing, while the residual porosity first steadily diminished and afterwards became constant. Furthermore, the variation in the total porosity and residual porosity of the coal cores continuously diminished with an increase in the level of metamorphism. The NMR permeability of the coal cores showed a similar pattern to the porosity. Accordingly, the optimal parameters for cryogenic L-CO2 cyclic injection during a complete working time were determined to be Nc = 4 and Pc = 30 min. A field test demonstrated that after L-CO2 cyclic freeze-thaw treatment, the average gas drainage concentration of a single borehole in the test region increased by 1.93 times, while the pure flow of a single gas drainage borehole increased by 2.21 times. Finally, the gas attenuation coefficient decreased from 0.036 to 0.012. We concluded that the proposed permeability enhancement technique transformed coal seams from hard-to-drain to drainable.
| S-EPMC9603266 | biostudies-literature
Project description:A study involving the use of Mg-MeOH for the double reductive cleavage of both N-S and C-S bonds in a series of 11 benzo-fused cyclic sulfonamides is reported. Examples where the sulfonamide nitrogen atom is part of a pyrrolidine ring effectively undergo reduction, as long as a methoxy substituent is not para-positioned in the aromatic ring, relative to the sulfonyl group. In contrast, if the nitrogen atom is contained within an aromatic ring (pyrrole or indole), the presence of a para-methoxy substituent does not prohibit reduction. If deuterated methanol is used, aromatic ortho-deuterium incorporation was observed. To better understand how structure affects reactivity, density functional theory calculations were performed using three functionals. Results using CAM-B3LYP were found to best correlate with experimental observations, and these demonstrate the impact that the different aromatic substitution patterns and types of N-atom have on the lowest unoccupied molecular orbital (LUMO) energies and adiabatic electron affinities.
| S-EPMC9486945 | biostudies-literature