Dataset Information

Does posterior configuration have similar strength as parallel configuration for treating comminuted distal humerus fractures? A cadaveric biomechanical study.

ABSTRACT:

Background

The posterior plating technique could be used as a clinical alternative to parallel plating for treating comminuted distal humerus fractures (DHFs) successfully with good clinical results. However, the biomechanical characteristics for posterior fixation are still unclear. The purpose of this study is to evaluate the biomechanical properties of the posterior fixation and to make comparisons between the parallel and the posterior fixation systems.

Materials and methods

We performed a cadaveric biomechanical testing with two posterior plating systems (a posterior two plating and a single posterior pre-contoured Y plating system) and one parallel two plating system to treat AO/OTA type-C2.3 DHFs. Among three groups, we compared construct stiffness, failure strength, and intercondylar width changes after 5000-cycle fatigue loading and failure loads and failure modes after destructive tests in both the axial compression and (sagittal) posterior bending directions. The correlations between construct failure loads and bone marrow density (BMD) were also compared.

Results

In axial direction, there were no significant differences in the stiffness and failure load between the posterior and the parallel constructs. However, in sagittal direction, the two-plate groups (posterior two plating and parallel plating group) had significant higher stiffness and failure loads than the one-plate group (single posterior Y plating). There was no fixation failure after 5000-cyclic loading in both directions for all groups. Positive correlation was noted between BMD and failure loads on parallel fixation.

Conclusions

We found that when using two plates for treating comminuted DHFs, there were no significant differences in terms of most biomechanical measurements between posterior and parallel fixation. However, the single pre-contoured posterior Y plate construct was biomechanically weaker in the sagittal plane than the parallel and the posterior two-plate constructs, although there was no fixation failure after the fatigue test for all groups regardless of the fixation methods.

Level of evidence

Biomechanical study.

SUBMITTER: Shih CA

PROVIDER: S-EPMC8122534 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:BackgroundProximal humerus fractures are the third most common in the human body but their management remains controversial. Open reduction and internal fixation with plates is one of the leading modes of operative treatment for these fractures. The development of technologies and techniques for these plates, during the recent decades, promise a bright future for their clinical use. A comprehensive review of in vitro biomechanical studies is needed for the comparison of plates' mechanical performance and the testing methodologies. This will not only guide clinicians with plate selection but also with the design of future in vitro biomechanical studies. This review was aimed to systematically categorise and review the in vitro biomechanical studies of these plates based on their protocols and discuss their results. The technologies and techniques investigated in these studies were categorised and compared to reach a census where possible.Methods and resultsWeb of Science and Scopus database search yielded 62 studies. Out of these, 51 performed axial loading, torsion, bending and/or combined bending and axial loading while 11 simulated complex glenohumeral movements by using tendons. Loading conditions and set-up, failure criteria and performance parameters, as well as results for each study, were reviewed. Only two studies tested four-part fracture model while the rest investigated two- and three-part fractures. In ten studies, synthetic humeri were tested instead of cadaveric ones. In addition to load-displacement data, three-dimensional motion analysis systems, digital image correlation and acoustic emission testing have been used for measurement.ConclusionsOverall, PHILOS was the most tested plate and locking plates demonstrated better mechanical performance than non-locking ones. Conflicting results have been published for their comparison with non-locking blade plates and polyaxial locking screws. Augmentation with cement [calcium phosphate or poly(methyl methacrylate)] or allografts (fibular and femoral head) was found to improve bone-plate constructs' mechanical performance. Controversy still lies over the use of rigid and semi-rigid implants and the insertion of inferomedial screws for calcar region support. This review will guide the design of in vitro and in silico biomechanical tests and also supplement the study of clinical literature.

Project description:Intramedullary fixation of comminuted mid-shaft clavicle fractures has traditionally been employed with satisfactory clinical outcomes; however, pins with smooth surfaces may protrude from the bone and are prone to migration, while some threaded pins are difficult to remove post-operatively. The aim of this proof-of-concept study was to develop and evaluate the biomechanical strength of a novel intramedullary Echidna pin device designed to maintain fracture reduction, resist migration and facilitate ease of post-operative removal.Thirty human clavicle specimens were harvested and fractured in a comminuted mid-shaft butterfly configuration. Each specimen was randomly allocated to three surgical repair groups including intramedullary fixation using the Echidna pin and Herbert Cannulated Bone Screw System, as well as plate fixation using bi-cortical locking screws. Using a biomechanical testing apparatus, construct bending and torsional stiffness were measured, as well as ultimate bending strength.There was no significant difference in torsional stiffness and ultimate bending moment between the Echidna pin and Herbert screw repair constructs (p > 0.05); however, the Echidna pin construct demonstrated a significantly greater bending stiffness compared to that of the Herbert screw construct (mean difference 0.55 Nm/deg., p = 0.001). The plate construct demonstrated significantly greater torsional stiffness, bending stiffness and ultimate bending moment compared to those of the Herbert screw and Echidna pin (p < 0.05).An intramedullary Echidna pin device was designed to stabilize comminuted fractures of the clavicle, maintain fracture compression and provide ease of removal post-operatively. Since the results suggest equivalent or superior torsional and bending stability in the Echidna pin compared to that of the Herbert screw, the Echidna pin concept may represent an alternative fixation device to conventional intramedullary screws, nails and pins; however, superior plating using bi-cortical locking screws provides substantially higher construct structural rigidity than intramedullary devices, and may therefore be useful in cases of osteoporotic bone, or where high fracture stability is required.

Project description:PurposeThe treatment of distal femur fractures with extensive metaphyseal comminution is frequently complicated by high rates of nonunion and varus collapse. Dual plating with lateral and medial locking plates for these types of fractures has shown promising results in the recent literature. We hypothesize that dual plating of comminuted distal femur fractures leads to higher union rates and lower revision rates compared to an isolated lateral locking plate.MethodsA retrospective medical chart review between January 2015 and December 2017 was conducted. Inclusion criteria included patients 18 years of age and older who sustained a complex distal femur fracture (AO/OTA 33-C2/33-C3 or periprosthetic fracture with significant metaphyseal comminution) and at least 6 months of follow up. Patients with simple fracture patterns, alternative fixation methods, and inadequate follow up were excluded. All patients in the single plating group were treated with a lateral distal femoral locking plate using a lateral approach. In the patients treated with dual plating, an extensile parapatellar approach was utilized for fracture reduction and placement of an adjunctive medial plate. Demographic information, fracture types, injury severity score (ISS), medical comorbidities, type of surgical fixation, union rates, complications, knee range of motion, time to follow up, and need for revision surgery were extrapolated from the medical charts for analysis.ResultsTwenty-one patients were included in the study. Thirteen patients underwent single plate fixation and 8 underwent dual plate fixation. There were no significant differences in demographics, number of co-morbidities, fracture classification, or ISS between single and dual plate groups (p > 0.05 for all). There was a statistically significant difference in union rates between the single plate group (6 nonunions, 4 unions, and 3 delayed unions) and the dual plate group, with no nonunions or delayed unions (p = 0.0049). Although not statistically significant, 4 patients treated with single plating underwent revision ORIF, compared to none in the dual plating group (p = 0.13). There were no significant differences in time to follow up, time to full weight bearing, or infection rates (p > 0.1 for all).ConclusionBased on these results, the medial and lateral locked plating technique demonstrates a higher union rate, with possible lower rates of revision surgery, compared to a single lateral plate in highly comminuted distal femur fractures.Level of evidenceLevel 3. Retrospective Cohort Study.