Robust Output Feedback Control of Single-Link Flexible-Joint Robot Manipulator with Matched Disturbances Using High Gain Observer.
Ontology highlight
ABSTRACT:
SUBMITTER: Ullah H
PROVIDER: S-EPMC8125959 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:PurposeDraf drainage is the standard treatment procedure for frontal sinus diseases. In this procedure, rigid angled endoscopes and rigid curved instruments are used. However, laterally located pathologies in the frontal sinus cannot be reached with rigid instrumentation. In order to assist surgeons with such complicated cases, we propose a novel handheld flexible manipulator system.MethodsA cross section of 3 mm × 4.6 mm enables transnasal guiding of a flexible endoscope with 1.4 mm diameter and a standard flexible surgical instrument with up to 1.8 mm diameter into the frontal sinus with increased reachability. The developed system consists of an electrical discharge-machined flexure hinge-based nitinol manipulator arm and a purely mechanical handheld control unit. The corresponding control unit enables upward and left-right bending of the manipulator arm, translation, rolling, actuation and also quick exchange of the surgical instrument. In order to verify the fulfillment of performance requirements, tests regarding reachability and payload capacity were conducted.ResultsReachability tests showed that the manipulator arm can be inserted into the frontal sinus and reach its lateral regions following a Draf IIa procedure. The system can exert forces of at least 2 N in the vertical direction and 1 N in the lateral direction which is sufficient for manipulation of frontal sinus pathologies.ConclusionConsidering the fact that the anatomical requirements of the frontal sinus are not addressed satisfactorily in the development of prospective flexible instruments, the proposed system shows great potential in terms of therapeutic use owing to its small cross section and dexterity.
| S-EPMC7419368 | biostudies-literature
Project description:This article presents a methodology to recycle and upgrade a 4-DOF educational robot manipulator with a gripper. The robot is upgraded by providing it an artificial vision that allows obtaining the position and shape of objects collected by it. A low-cost and open-source hardware solution is also proposed to achieve motion control of the robot through a decentralized control scheme. The robot joints are actuated through five direct current motors coupled to optical encoders. Each encoder signal is fed to a proportional integral derivative controller with anti-windup that employs the motor velocity provided by a state observer. The motion controller works with only two open-architecture Arduino Mega boards, which carry out data acquisition of the optical encoder signals. MATLAB-Simulink is used to implement the controller as well as a friendly graphical interface, which allows the user to interact with the manipulator. The communication between the Arduino boards and MATLAB-Simulink is performed in real-time utilizing the Arduino IO Toolbox. Through the proposed controller, the robot follows a trajectory to collect a desired object, avoiding its collision with other objects. This fact is verified through a set of experiments presented in the paper.
| S-EPMC7146749 | biostudies-literature
Project description:Effective feedback control requires all state variable information of the system. However, in the translational flexible-link manipulator (TFM) system, it is unrealistic to measure the vibration signals and their time derivative of any points of the TFM by infinite sensors. With the rigid-flexible coupling between the global motion of the rigid base and the elastic vibration of the flexible-link manipulator considered, a two-time scale virtual sensor, which includes the speed observer and the vibration observer, is designed to achieve the estimation for the vibration signals and their time derivative of the TFM, as well as the speed observer and the vibration observer are separately designed for the slow and fast subsystems, which are decomposed from the dynamic model of the TFM by the singular perturbation. Additionally, based on the linear-quadratic differential games, the observer gains of the two-time scale virtual sensor are optimized, which aims to minimize the estimation error while keeping the observer stable. Finally, the numerical calculation and experiment verify the efficiency of the designed two-time scale virtual sensor.
| S-EPMC5134463 | biostudies-literature
Project description:With the increasing demand for robotic manipulators to operate in complex environments, it is important to develop designs that work in obstacle-rich environments and can navigate around obstacles. This paper aims to demonstrate the capabilities of a bio-inspired, underactuated multilink manipulator in environments with fixed and/or movable obstacles. To simplify the system design, a single rotational actuator is used at the base of the manipulator. We present a modeling method for flexible, multilink underactuated manipulators, including their interaction with obstacles. We also demonstrate how to plan a trajectory for the manipulator in environments with fixed obstacles. The robustness of the manipulator is examined by analyzing the effects of uncertainty in its initial state and the position of obstacles. Next, we demonstrate the performance of the manipulator in environments with movable obstacles and show the advantages of controlling the obstacles' radii and positions. Lastly, we showcase the process of picking up an object in workspaces with obstacles. All the findings are supported by simulations as well as hardware experiments.
| S-EPMC10886640 | biostudies-literature
Project description:For industrial manufacturing, industrial robots are required to work together with human counterparts on certain special occasions, where human workers share their skills with robots. Intuitive human?robot interaction brings increasing safety challenges, which can be properly addressed by using sensor-based active control technology. In this article, we designed and fabricated a three-dimensional flexible robot skin made by the piezoresistive nanocomposite based on the need for enhancement of the security performance of the collaborative robot. The robot skin endowed the YuMi robot with a tactile perception like human skin. The developed sensing unit in the robot skin showed the one-to-one correspondence between force input and resistance output (percentage change in impedance) in the range of 0?6.5 N. Furthermore, the calibration result indicated that the developed sensing unit is capable of offering a maximum force sensitivity (percentage change in impedance per Newton force) of 18.83% N-1 when loaded with an external force of 6.5 N. The fabricated sensing unit showed good reproducibility after loading with cyclic force (0?5.5 N) under a frequency of 0.65 Hz for 3500 cycles. In addition, to suppress the bypass crosstalk in robot skin, we designed a readout circuit for sampling tactile data. Moreover, experiments were conducted to estimate the contact/collision force between the object and the robot in a real-time manner. The experiment results showed that the implemented robot skin can provide an efficient approach for natural and secure human?robot interaction.
| S-EPMC6266199 | biostudies-literature
Project description:This study investigates the dynamics and trajectory tracking of quadcopters by utilizing the Disturbance Observer-based Control (DOBC) algorithm. The quadcopter's dynamic model, which consists of six degrees of freedom, includes both disturbances and uncertainties in the model. The DOBC approach incorporates the disturbance model into the system by introducing it at the input variables. It then compensates for disturbances to achieve accurate tracking of different reference trajectories. The simulated trajectories span a range of motion, varying from simple straight paths to complex spiral paths. In order to verify and evaluate the efficacy of the suggested control technique, simulations are performed using MATLAB. The simulations conclusively show that the disturbance observer-based method effectively achieves the tracking of specified reference trajectories in three-dimensional space. The study highlights the effectiveness of the DOBC algorithm in reducing the effects of disturbances and uncertainties, thereby improving the quadcopter's capacity to accurately track various trajectories.
| S-EPMC10909193 | biostudies-literature
Project description:There are high risks of infection for surgeons during the face-to-face COVID-19 swab sampling due to the novel coronavirus's infectivity. To address this issue, we propose a flexible transoral robot with a teleoperated configuration for swab sampling. The robot comprises a flexible manipulator, an endoscope with a monitor, and a master device. A 3-prismatic-universal (3-PU) flexible parallel mechanism with 3 degrees of freedom (DOF) is used to realize the manipulator's movements. The flexibility of the manipulator improves the safety of testees. Besides, the master device is similar to the manipulator in structure. It is easy to use for operators. Under the guidance of the vision from the endoscope, the surgeon can operate the master device to control the swab's motion attached to the manipulator for sampling. In this paper, the robotic system, the workspace, and the operation procedure are described in detail. The tongue depressor, which is used to prevent the tongue's interference during the sampling, is also tested. The accuracy of the manipulator under visual guidance is validated intuitively. Finally, the experiment on a human phantom is conducted to demonstrate the feasibility of the robot preliminarily.
| S-EPMC8072391 | biostudies-literature
Project description:The olfactory bulb receives rich glutamatergic projections from the piriform cortex. However, the dynamics and importance of these feedback signals remain unknown. Here, we use multiphoton calcium imaging to monitor cortical feedback in the olfactory bulb of awake mice and further probe its impact on the bulb output. Responses of feedback boutons were sparse, odor specific, and often outlasted stimuli by several seconds. Odor presentation either enhanced or suppressed the activity of boutons. However, any given bouton responded with stereotypic polarity across multiple odors, preferring either enhancement or suppression. Feedback representations were locally diverse and differed in dynamics across bulb layers. Inactivation of piriform cortex increased odor responsiveness and pairwise similarity of mitral cells but had little impact on tufted cells. We propose that cortical feedback differentially impacts these two output channels of the bulb by specifically decorrelating mitral cell responses to enable odor separation.
| S-EPMC7448302 | biostudies-literature
Project description:Multisensory integration is a prerequisite for effective locomotor control in most animals. Especially, the impressive aerial performance of insects relies on rapid and precise integration of multiple sensory modalities that provide feedback on different time scales. In flies, continuous visual signalling from the compound eyes is fused with phasic proprioceptive feedback to ensure precise neural activation of wing steering muscles (WSM) within narrow temporal phase bands of the stroke cycle. This phase-locked activation relies on mechanoreceptors distributed over wings and gyroscopic halteres. Here we investigate visual steering performance of tethered flying fruit flies with reduced haltere and wing feedback signalling. Using a flight simulator, we evaluated visual object fixation behaviour, optomotor altitude control and saccadic escape reflexes. The behavioural assays show an antagonistic effect of wing and haltere signalling on visuomotor gain during flight. Compared with controls, suppression of haltere feedback attenuates while suppression of wing feedback enhances the animal's wing steering range. Our results suggest that the generation of motor commands owing to visual perception is dynamically controlled by proprioception. We outline a potential physiological mechanism based on the biomechanical properties of WSM and sensory integration processes at the level of motoneurons. Collectively, the findings contribute to our general understanding how moving animals integrate sensory information with dynamically changing temporal structure.
| S-EPMC4736939 | biostudies-literature
Project description:The nonlinear dynamics of a bird-like flapping wing robot under randomly uncertain disturbances was studied in this study. The bird-like flapping wing robot was first simplified into a two-rod model with a spring connection. Then, the dynamic model of the robot under randomly uncertain disturbances was established according to the principle of moment equilibrium, and the disturbances were modeled in the form of bounded noise. Next, the energy model of the robot was established. Finally, numerical simulations and experiments were carried out based on the above models. The results show that the robot is more likely to deviate from its normal trajectory when the randomly uncertain disturbances are applied in a chaotic state than in a periodic state. With the increase of the spring stiffness under the randomly uncertain disturbances, the robot has a stronger ability to reject the disturbances. The mass center of the robot is vital to realize stable flights. The greater the amplitude of randomly uncertain disturbances, the more likely it is for the robot to be in a divergent state.
| S-EPMC7200001 | biostudies-literature