Browse
Submit Data
Databases
API
Help

Dataset Information

16 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Large-Scale Synthesis of Semiconducting Cu(In,Ga)Se₂ Nanoparticles for Screen Printing Application.

ABSTRACT: During the last few decades, the interest over chalcopyrite and related photovoltaics has been growing due the outstanding structural and electrical properties of the thin-film Cu(In,Ga)Se₂ photoabsorber. More recently, thin film deposition through solution processing has gained increasing attention from the industry, due to the potential low-cost and high-throughput production. To this end, the elimination of the selenization procedure in the synthesis of Cu(In,Ga)Se₂ nanoparticles with following dispersion into ink formulations for printing/coating deposition processes are of high relevance. However, most of the reported syntheses procedures give access to tetragonal chalcopyrite Cu(In,Ga)Se₂ nanoparticles, whereas methods to obtain other structures are scarce. Herein, we report a large-scale synthesis of high-quality Cu(In,Ga)Se₂ nanoparticles with wurtzite hexagonal structure, with sizes of 10-70 nm, wide absorption in visible to near-infrared regions, and [Cu]/[In + Ga] ≈ 0.8 and [Ga]/[Ga + In] ≈ 0.3 metal ratios. The inclusion of the synthesized NPs into a water-based ink formulation for screen printing deposition results in thin films with homogenous thickness of ≈4.5 µm, paving the way towards environmentally friendly roll-to-roll production of photovoltaic systems.

SUBMITTER: Goncalves BF

PROVIDER: S-EPMC8147049 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Electron-Selective TiO2 Contact for Cu(In,Ga)Se2 Solar Cells.

Project description:The non-toxic and wide bandgap material TiO2 is explored as an n-type buffer layer on p-type Cu(In,Ga)Se2 (CIGS) absorber layer for thin film solar cells. The amorphous TiO2 thin film deposited by atomic layer deposition process at low temperatures shows conformal coverage on the CIGS absorber layer. Solar cells from non-vacuum deposited CIGS absorbers with TiO2 buffer layer result in a high short-circuit current density of 38.9?mA/cm(2) as compared to 36.9?mA/cm(2) measured in the reference cell with CdS buffer layer, without compromising open-circuit voltage. The significant photocurrent gain, mainly in the UV part of the spectrum, can be attributed to the low parasitic absorption loss in the ultrathin TiO2 layer (~10?nm) with a larger bandgap of 3.4?eV compared to 2.4?eV of the traditionally used CdS. Overall the solar cell conversion efficiency was improved from 9.5% to 9.9% by substituting the CdS by TiO2 on an active cell area of 10.5?mm(2). Optimized TiO2/CIGS solar cells show excellent long-term stability. The results imply that TiO2 is a promising buffer layer material for CIGS solar cells, avoiding the toxic CdS buffer layer with added performance advantage.

| S-EPMC4630620 | biostudies-literature

ALD-Zn xTi yO as Window Layer in Cu(In,Ga)Se2 Solar Cells.

Project description:We report on the application of Zn xTi yO deposited by atomic layer deposition (ALD) as buffer layer in thin film Cu(In,Ga)Se2 (CIGS) solar cells to improve the photovoltaic device performance. State-of-the-art CIGS devices employ a CdS/ZnO layer stack sandwiched between the absorber layer and the front contact. Replacing the sputter deposited ZnO with ALD-Zn xTi yO allowed a reduction of the CdS layer thickness without adversely affecting open-circuit voltage ( VOC). This leads to an increased photocurrent density with a device efficiency of up to 20.8% by minimizing the parasitic absorption losses commonly observed for CdS. ALD was chosen as method to deposit homogeneous layers of Zn xTi yO with varying Ti content with a [Ti]/([Ti] + [Zn]) atomic fraction up to ?0.35 at a relatively low temperature of 373 K. The Ti content influenced the absorption behavior of the Zn xTi yO layer by increasing the optical bandgap >3.5 eV in the investigated range. Temperature-dependent current-voltage ( I- V) measurements of solar cells were performed to investigate the photocurrent blocking behavior observed for high Ti content. Possible conduction band discontinuities introduced by Zn xTi yO are discussed based on X-ray photoelectron spectroscopy (XPS) measurements.

| S-EPMC6302902 | biostudies-literature

Four-Fold Multi-Modal X-ray Microscopy Measurements of a Cu(In,Ga)Se2 Solar Cell.

Project description:Inhomogeneities and defects often limit the overall performance of thin-film solar cells. Therefore, sophisticated microscopy approaches are sought to characterize performance and defects at the nanoscale. Here, we demonstrate, for the first time, the simultaneous assessment of composition, structure, and performance in four-fold multi-modality. Using scanning X-ray microscopy of a Cu(In,Ga)Se2 (CIGS) solar cell, we measured the elemental distribution of the key absorber elements, the electrical and optical response, and the phase shift of the coherent X-rays with nanoscale resolution. We found structural features in the absorber layer-interpreted as voids-that correlate with poor electrical performance and point towards defects that limit the overall solar cell efficiency.

| S-EPMC7796438 | biostudies-literature

Damp Heat Treatment of Cu(In,Ga)Se2 Solar Cells with Different Sodium Content.

Project description:Long term stability is crucial to maturing any photovoltaic technology. We have studied the influence of sodium, which plays a key role in optimizing the performance of Cu(In,Ga)Se2 (CIGSe) solar cells, on the long-term stability of flexible CIGSe solar cells on polyimide foil. The standardized procedure of damp heat exposure (85% relative humidity at 85 °C) was used to simulate aging of the unencapsulated cells in multiple time steps while they were characterized by current-voltage analysis, capacitance-voltage profiling, as well as electroluminescence imaging. By comparing the aging process to cells that were exposed to heat only, it could be confirmed that moisture plays the key role in the degradation process. We found that cells with higher sodium content suffer from a more pronounced degradation. Furthermore, the experimental results indicate the superposition of an enhancing and a deteriorating mechanism during the aging process. We propose an explanation based on the corrosion of the planar contacts of the solar cell.

| S-EPMC5452750 | biostudies-other

Characterization of efficiency-limiting resistance losses in monolithically integrated Cu(In,Ga)Se2 solar modules.

Project description:The cell-to-module efficiency gap in Cu(In,Ga)Se2 (CIGS) monolithically integrated solar modules is enhanced by contact resistance between the Al-doped ZnO (AZO) and Mo back contact layers, the P2 contact, which connects adjacent cells. The present work evaluated the P2 contact resistance, in addition to the TCO resistance, using an embedded transmission line structure in a commercial-grade module without using special sample fabrication methods. The AZO layers between cells were not scribed; instead, the CIGS/CdS/i-ZnO/AZO device was patterned in a long stripe to permit measurement of the Mo electrode pair resistance over current paths through two P2 contacts (Mo/AZO) and along the AZO layer. The intercept and slope of the resistance as a function of the electrode interval yielded the P2 contact resistance and the TCO resistance, respectively. Calibration of the parasitic resistances is discussed as a method of improving the measurement accuracy. The contribution of the P2 contact resistance to the series resistance was comparable to that of the TCO resistance, and its origin was attributed to remnant MoSe2 phases in the P2 region, as verified by transmission electron microscopy.

| S-EPMC4287749 | biostudies-other

Data on lateral photocurrent along a Cu(In,Ga)Se2 thin film as a function of air exposure time.

Project description:Wavelength-dependent (i.e. penetration-depth-dependent) lateral photocurrent (i LP ) measurement has been used to extract depth-resolved L c profiles, where L c is the minority carrier collection length by diffusion. The extracted L c depth-profiles can be used to determine the minority carrier diffusion length and back-surface recombination velocity in Cu(In,Ga)Se2 (CIGS) thin film solar cells (Chung, 2019). During the measurement of i LP , the CIGS thin film is generally exposed to air. The CIGS thin films can be degraded by air exposure (Metzger et al., 2009). Therefore, it will be helpful to know the effect of air exposure time of CIGS thin films on the i LP values to properly estimate the electrical quality of CIGS thin films.

| S-EPMC6831709 | biostudies-literature

Large-Scale Production of Large-Size Atomically Thin Semiconducting Molybdenum Dichalcogenide Sheets in Water and Its Application for Supercapacitor.

Project description:To progress from laboratory research to commercial applications, it is necessary to develop an effective method to prepare large quantities and high-quality of the large-size atomically thin molybdenum dichalcogenides (MoS2). Aqueous-phase processes provide a viable method for producing thin MoS2 sheets using organolithium-assisted exfoliation; unfortunately, this method is hindered by changing pristine semiconducting 2H phase to distorted metallic 1T phase. Recovery of the intrinsic 2H phase typically involves heating of the 1T MoS2 sheets on solid substrates at high temperature. This has restricted and hindered the utilization of 2H phase MoS2 sheets suspensions. Here, we demonstrate that the synergistic effect of the rigid planar structure and charged nature of organic salt such as imidazole (ImH) can be successfully used to produce atomically thin 2H-MoS2 sheets suspension in water. Moreover, lateral size and area of the exfoliated sheet can be up to 50??m and 1000??m(2), respectively. According to the XPS measurements, nearly 100% of the 2H-MoS2 sheets was successfully prepared. A composite paper supercapacitor using the exfoliated 2H-MoS2 and carbon nanotubes delivered a superior volumetric capacitance of ~410?F/cm(3). Therefore, the organic salts-assisted liquid-phase exfoliation has great potential for large-scale production of 2H-MoS2 suspensions for supercapacitor application.

| S-EPMC4881041 | biostudies-literature

3D Screen Printing Offers Unprecedented Anticounterfeiting Strategies for Oral Solid Dosage Forms Feasible for Large Scale Production.

Project description:A threat to human health in developed and, in particular, in developing countries, counterfeit medicines represent the largest identified fraud market worldwide. 3D screen printing (3DSP), an additive manufacturing technology that enables large-scale production, offers unique opportunities to combat counterfeit drugs. One such possibility is the generation of oral dosage forms with a distinct colored inner structure that becomes visible upon breakage and cannot be copied with conventional manufacturing methods. To illustrate this, we designed tablets containing a blue cross. Owing to paste properties and the limited dimensions of the cross, the production process was chosen to be continuous, involving two screen and paste changes. The two pastes (tablet body, cross) were identical except for the blue color of the latter. This ensured the build-up and mechanical stability of the resulting tablets in a mass production environment. The ensuing tablets were found to be uniform in weight and size and to comply with regulatory requirements for hardness, friability, and disintegration time (immediate release). Moreover, all tablets exhibited the covert anticounterfeit feature. The study delivers a proof-of-concept for incorporating complex structures into tablets using 3DSP and showcases the power of the technology offering new avenues for combating counterfeit drugs.

| S-EPMC10974705 | biostudies-literature

Preparation and layer-by-layer solution deposition of Cu(In,Ga)O2 nanoparticles with conversion to Cu(In,Ga)S2 films.

Project description:We present a method of Cu(In,Ga)S2 (CIGS) thin film formation via conversion of layer-by-layer (LbL) assembled Cu-In-Ga oxide (CIGO) nanoparticles and polyelectrolytes. CIGO nanoparticles were created via a novel flame-spray pyrolysis method using metal nitrate precursors, subsequently coated with polyallylamine (PAH), and dispersed in aqueous solution. Multilayer films were assembled by alternately dipping quartz, Si, and/or Mo substrates into a solution of either polydopamine (PDA) or polystyrenesulfonate (PSS) and then in the CIGO-PAH dispersion to fabricate films as thick as 1-2 microns. PSS/CIGO-PAH films were found to be inadequate due to weak adhesion to the Si and Mo substrates, excessive particle diffusion during sulfurization, and mechanical softness ill-suited to further processing. PDA/CIGO-PAH films, in contrast, were more mechanically robust and more tolerant of high temperature processing. After LbL deposition, films were oxidized to remove polymer and sulfurized at high temperature under flowing hydrogen sulfide to convert CIGO to CIGS. Complete film conversion from the oxide to the sulfide is confirmed by X-ray diffraction characterization.

| S-EPMC4062496 | biostudies-literature

In-Situ Probing Plasmonic Energy Transfer in Cu(In, Ga)Se2 Solar Cells by Ultrabroadband Femtosecond Pump-Probe Spectroscopy.

Project description:In this work, we demonstrated a viable experimental scheme for in-situ probing the effects of Au nanoparticles (NPs) incorporation on plasmonic energy transfer in Cu(In, Ga)Se2 (CIGS) solar cells by elaborately analyzing the lifetimes and zero moment for hot carrier relaxation with ultrabroadband femtosecond pump-probe spectroscopy. The signals of enhanced photobleach (PB) and waned photoinduced absorption (PIA) attributable to surface plasmon resonance (SPR) of Au NPs were in-situ probed in transient differential absorption spectra. The results suggested that substantial carriers can be excited from ground state to lower excitation energy levels, which can reach thermalization much faster with the existence of SPR. Thus, direct electron transfer (DET) could be implemented to enhance the photocurrent of CIGS solar cells. Furthermore, based on the extracted hot carrier lifetimes, it was confirmed that the improved electrical transport might have been resulted primarily from the reduction in the surface recombination of photoinduced carriers through enhanced local electromagnetic field (LEMF). Finally, theoretical calculation for resonant energy transfer (RET)-induced enhancement in the probability of exciting electron-hole pairs was conducted and the results agreed well with the enhanced PB peak of transient differential absorption in plasmonic CIGS film. These results indicate that plasmonic energy transfer is a viable approach to boost high-efficiency CIGS solar cells.

| S-EPMC4683378 | biostudies-other