Browse
Submit Data
Databases
API
Help

Dataset Information

23 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Tunning of Templated CuWO₄ Nanorods Arrays Thickness to Improve Photoanode Water Splitting.

ABSTRACT: The fabrication of the photoanode of the n-type CuWO₄ nanorod arrays was successfully carried out through electrochemical deposition using anodic aluminum oxide (AAO) control templates and for the first time produced distinct gaps between the nanorod arrays. The effectiveness and efficiency of the resulting deposition was shown by the performance of the photoelectrochemical (PEC) procedure with a current density of 1.02 mA cm^-2 with irradiation using standard AM 1.5G solar simulator and electron changed radiation of 0.72% with a bias potential of 0.71 V (vs. Ag/AgCl). The gap between each nanorod indicated an optimization of the electrolyte penetration on the interface, which resulted in the expansion of the current density as much as 0.5 × 10²⁴ cm^-3 with a flat band potential of 0.14 V vs. Ag/AgCl and also a peak quantum efficiency of wavelength 410 nm. Thus, also indicating the gaps between the nanorod arrays is a promising structure to optimize the performance of the PEC water splitting procedure as a sustainable energy source.

SUBMITTER: Nasori N

PROVIDER: S-EPMC8153333 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Highly active deficient ternary sulfide photoanode for photoelectrochemical water splitting.

Project description:The exploration of photoanode materials with high efficiency and stability is the eternal pursuit for the realization of practically solar-driven photoelectrochemical (PEC) water splitting. Here we develop a deficient ternary metal sulfide (CdIn2S4) photoanode, and its PEC performance is significantly enhanced by introducing surface sulfur vacancies, achieving a photocurrent density of 5.73 mA cm-2 at 1.23 V vs. RHE and 1 Sun with an applied bias photon-to-current efficiency of 2.49% at 0.477 V vs. RHE. The experimental characterizations and theoretical calculations highlight the enhanced effect of surface sulfur vacancies on the interfacial charge separation and transfer kinetics, which also demonstrate the restrained surface states distribution and the transformation of active sites after introducing surface sulfur vacancies. This work may inspire more excellent work on developing sulfide-based photoanodes.

| S-EPMC7299993 | biostudies-literature

Hierarchical Co-Pi Clusters/Fe2O3 Nanorods/FTO Micropillars 3D Branched Photoanode for High-Performance Photoelectrochemical Water Splitting.

Project description:In this study, an efficient hierarchical Co-Pi cluster/Fe2O3 nanorod/fluorine-doped tin oxide (FTO) micropillar three-dimensional (3D) branched photoanode was designed for enhanced photoelectrochemical performance. A periodic array of FTO micropillars, which acts as a highly conductive "host" framework for uniform light scattering and provides an extremely enlarged active area, was fabricated by direct printing and mist-chemical vapor deposition (CVD). Fe2O3 nanorods that act as light absorber "guest" materials and Co-Pi clusters that give rise to random light scattering were synthesized via a hydrothermal reaction and photoassisted electrodeposition, respectively. The hierarchical 3D branched photoanode exhibited enhanced light absorption efficiency because of multiple light scattering, which was a combination of uniform light scattering from the periodic FTO micropillars and random light scattering from the Fe2O3 nanorods. Additionally, the large surface area of the 3D FTO micropillar, together with the surface area provided by the one-dimensional Fe2O3 nanorods, contributed to a remarkable increase in the specific area of the photoanode. Because of these enhancements and further improvements facilitated by decoration with a Co-Pi catalyst that enhanced water oxidation, the 3D branched Fe2O3 photoanode achieved a photocurrent density of 1.51 mA cm-2 at 1.23 VRHE, which was 5.2 times higher than that generated by the non-decorated flat Fe2O3 photoanode.

| S-EPMC9611282 | biostudies-literature

Atomically dispersed iridium catalysts on silicon photoanode for efficient photoelectrochemical water splitting.

Project description:Stabilizing atomically dispersed single atoms (SAs) on silicon photoanodes for photoelectrochemical-oxygen evolution reaction is still challenging due to the scarcity of anchoring sites. Here, we elaborately demonstrate the decoration of iridium SAs on silicon photoanodes and assess the role of SAs on the separation and transfer of photogenerated charge carriers. NiO/Ni thin film, an active and highly stable catalyst, is capable of embedding the iridium SAs in its lattices by locally modifying the electronic structure. The isolated iridium SAs enable the effective photogenerated charge transport by suppressing the charge recombination and lower the thermodynamic energy barrier in the potential-determining step. The Ir SAs/NiO/Ni/ZrO2/n-Si photoanode exhibits a benchmarking photoelectrochemical performance with a high photocurrent density of 27.7 mA cm-2 at 1.23 V vs. reversible hydrogen electrode and 130 h stability. This study proposes the rational design of SAs on silicon photoelectrodes and reveals the potential of the iridium SAs to boost photogenerated charge carrier kinetics.

| S-EPMC9899270 | biostudies-literature

Amorphization activated ruthenium-tellurium nanorods for efficient water splitting.

Project description:Pursuing active and durable water splitting electrocatalysts is of vital significance for solving the sluggish kinetics of the oxygen evolution reaction (OER) process in energy supply. Herein, theoretical calculations identify that the local distortion-strain effect in amorphous RuTe2 system abnormally sensitizes the Te-pπ coupling capability and enhances the electron-transfer of Ru-sites, in which the excellent inter-orbital p-d transfers determine strong electronic activities for boosting OER performance. Thus, a robust electrocatalyst based on amorphous RuTe2 porous nanorods (PNRs) is successfully fabricated. In the acidic water splitting, a-RuTe2 PNRs exhibit a superior performance, which only require a cell voltage of 1.52 V to reach a current density of 10 mA cm-2. Detailed investigations show that the high density of defects combine with oxygen atoms to form RuOxHy species, which are conducive to the OER. This work offers valuable insights for constructing robust electrocatalysts based on theoretical calculations guided by rational design and amorphous materials.

| S-EPMC6908605 | biostudies-literature

Controlled fabrication of Sn/TiO2 nanorods for photoelectrochemical water splitting.

Project description:In this work, we investigate the controlled fabrication of Sn-doped TiO2 nanorods (Sn/TiO2 NRs) for photoelectrochemical water splitting. Sn is incorporated into the rutile TiO2 nanorods with Sn/Ti molar ratios ranging from 0% to 3% by a simple solvothermal synthesis method. The obtained Sn/TiO2 NRs are single crystalline with a rutile structure. The concentration of Sn in the final nanorods can be well controlled by adjusting the molar ratio of the precursors. Photoelectrochemical experiments are conducted to explore the photocatalytic activity of Sn/TiO2 NRs with different doping levels. Under the illumination of solar simulator with the light intensity of 100 mW/cm2, our measurements reveal that the photocurrent increases with increasing doping level and reaches the maximum value of 1.01 mA/cm2 at -0.4 V versus Ag/AgCl, which corresponds to up to about 50% enhancement compared with the pristine TiO2 NRs. The Mott-Schottky plots indicate that incorporation of Sn into TiO2 nanorod can significantly increase the charge carrier density, leading to enhanced conductivity of the nanorod. Furthermore, we demonstrate that Sn/TiO2 NRs can be a promising candidate for photoanode in photoelectrochemical water splitting because of their excellent chemical stability.

| S-EPMC4228341 | biostudies-literature

High-performance and stable photoelectrochemical water splitting cell with organic-photoactive-layer-based photoanode.

Project description:Considering their superior charge-transfer characteristics, easy tenability of energy levels, and low production cost, organic semiconductors are ideal for photoelectrochemical (PEC) hydrogen production. However, organic-semiconductor-based photoelectrodes have not been extensively explored for PEC water-splitting because of their low stability in water. Herein, we report high-performance and stable organic-semiconductors photoanodes consisting of p-type polymers and n-type non-fullerene materials, which is passivated using nickel foils, GaIn eutectic, and layered double hydroxides as model materials. We achieve a photocurrent density of 15.1 mA cm-2 at 1.23 V vs. reversible hydrogen electrode (RHE) with an onset potential of 0.55 V vs. RHE and a record high half-cell solar-to-hydrogen conversion efficiency of 4.33% under AM 1.5 G solar simulated light. After conducting the stability test at 1.3 V vs. RHE for 10 h, 90% of the initial photocurrent density are retained, whereas the photoactive layer without passivation lost its activity within a few minutes.

| S-EPMC7606446 | biostudies-literature

Coordination Chemistry Engineered Polymeric Carbon Nitride Photoanode with Ultralow Onset Potential for Water Splitting.

Project description:Construction of an intimate film/substrate interface is of great importance for a photoelectrode to achieve efficient photoelectrochemical performance. Inspired by coordination chemistry, a polymeric carbon nitride (PCN) film is intimately grown on a Ti-coated substrate by an in situ thermal condensation process. The as-prepared PCN photoanode exhibits a record low onset potential (Eonset ) of -0.38 V versus the reversible hydrogen electrode (RHE) and a decent photocurrent density of 242 μA cm-2 at 1.23 VRHE for water splitting. Detailed characterization confirms that the origin of the ultralow onset potential is mainly attributed to the substantially reduced interfacial resistance between the Ti-coated substrate and the PCN film benefitting from the constructed interfacial sp2 N→Ti coordination bonds. For the first time, the ultralow onset potential enables the PCN photoanode to drive water splitting without external bias with a stable photocurrent density of ≈9 μA cm-2 up to 1 hour.

| S-EPMC9401030 | biostudies-literature

Au@CdS Core-Shell Nanoparticles-Modified ZnO Nanowires Photoanode for Efficient Photoelectrochemical Water Splitting.

Project description:Hydrogen production from water splitting using solar energy based on photoelectrochemical (PEC) cells has attracted increasing attention because it leaves less of a carbon footprint and has economic superiority of solar and hydrogen energy. Oxide semiconductors such as ZnO possessing high stability against photocorrosion in hole scavenger systems have been widely used to build photoanodes of PEC cells but under visible light their conversion efficiencies with respect to incident-photon-to-current conversion efficiency (IPCE) measured without external bias are still not satisfied. An innovative way is presented here to significantly improve the conversion efficiency of PEC cells by constructing a core-shell structure-based photoanode comprising Au@CdS core-shell nanoparticles on ZnO nanowires (Au@CdS-ZnO). The Au core offers strong electronic interactions with both CdS and ZnO resulting in a unique nanojunction to facilitate charge transfer. The Au@CdS-ZnO PEC cell under 400 nm light irradiation without any applied bias provides an IPCE of 14.8%. Under AM1.5 light illumination with a bias of 0.4 V, the Au@CdS-ZnO PEC cell produces H2 at a constant rate of 11.5 μmol h-1 as long as 10 h. This work provides a fundamental insight to improve the conversion efficiency for visible light in water splitting.

| S-EPMC5115296 | biostudies-literature

Crystallinity Engineering of Hematite Nanorods for High-Efficiency Photoelectrochemical Water Splitting.

Project description:An effective strategy to overcome the morphology evolution of hematite nanorods under high-temperature activation is presented, via tuning the crystallinity and sintering temperature by substrate modification. It is demonstrated that the as-prepared doping-free hematite nanorods with fine nanostructures obtain a significantly higher photocurrent density of 2.12 mA cm-2 at 1.23 V versus RHE, due to effective charge separation and transfer.

| S-EPMC5016786 | biostudies-literature

Embedding laser generated nanocrystals in BiVO4 photoanode for efficient photoelectrochemical water splitting.

Project description:Addressing the intrinsic charge transport limitation of metal oxides has been of significance for pursuing viable PEC water splitting photoelectrodes. Growing a photoelectrode with conductive nanoobjects embedded in the matrix is promising for enhanced charge transport but remains a challenge technically. We herein show a strategy of embedding laser generated nanocrystals in BiVO4 photoanode matrix, which achieves photocurrent densities of up to 5.15 mA cm-2 at 1.23 VRHE (from original 4.01 mA cm-2) for a single photoanode configuration, and 6.22 mA cm-2 at 1.23 VRHE for a dual configuration. The enhanced performance by such embedding is found universal owing to the typical features of laser synthesis and processing of colloids (LSPC) for producing ligand free nanocrystals in desired solvents. This study provides an alternative to address the slow bulk charge transport that bothers most metal oxides, and thus is significant for boosting their PEC water splitting performance.

| S-EPMC6565742 | biostudies-literature