Browse
Submit Data
Databases
API
Help

Dataset Information

9 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Hydroxymethylfurfural as an Intermediate of Cellulose Carbonization.

ABSTRACT: Hydrogen bond donor solvents such as aromatic solvents inhibit the secondary degradation of cellulose-derived primary pyrolysis products. In a previous study, we found that the formation of solid carbonized products was completely inhibited during cellulose pyrolysis in aromatic solvents, with 5-hydroxymethylfurfural (5-HMF) recovered in certain yields instead. This indicated that 5-HMF is an intermediate in cellulose carbonization. To confirm this hypothesis, the thermal reactivity of 5-HMF was investigated. At 280 °C, pure 5-HMF polymerized into a hard glassy substance through OH group elimination, but further conversion was slow. When pyrolyzed in the presence of glycerol, a model of coexisting primary pyrolysis products from cellulose, a coupling reaction proceeded. Reactions characteristic of cellulose carbonization then occurred, including the formation of acidic groups and benzene-type structures in the solid products. These results confirmed the above hypothesis. The molecular mechanism of cellulose carbonization is discussed, focusing on the crystalline nature.

SUBMITTER: Nomura T

PROVIDER: S-EPMC8173002 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Carbonization of cellulose cell wall evaluated with ultraviolet microscopy.

Project description:This is the first study of cellulose carbonization in the interior of cell walls. Cotton cellulose was pyrolyzed under nitrogen or in aromatic solvents (benzophenone, diphenyl sulfide, and 1,3-diphenoxybenzene) at 280 °C, and cross sections of the cell walls were examined using ultraviolet (UV) microscopy. After pyrolysis under nitrogen, UV absorption caused by carbonization appeared inside the cell walls. The absorptivity of the cell interiors was homogeneous and slightly lower than that of the cell surfaces. The UV spectra had maximal absorption at ca. 250 nm. The spectra of model compounds and Py-GC/MS analysis data suggested that furanic and polycyclic aromatic structures were present in the carbonized products. The use of aromatic solvents decreased the yields of solid carbonized products and the UV absorptivity, which remained homogeneous throughout the cross sections. The mechanism of cellulose carbonization in cell walls is discussed along with the influence of aromatic solvents.

| S-EPMC9049861 | biostudies-literature

Continuous Stabilization and Carbonization of a Lignin-Cellulose Precursor to Carbon Fiber.

Project description:The demand for carbon fibers (CFs) based on renewable raw materials as the reinforcing fiber in composites for lightweight applications is growing. Lignin-cellulose precursor fibers (PFs) are a promising alternative, but so far, there is limited knowledge of how to continuously convert these PFs under industrial-like conditions into CFs. Continuous conversion is vital for the industrial production of CFs. In this work, we have compared the continuous conversion of lignin-cellulose PFs (50 wt % softwood kraft lignin and 50 wt % dissolving-grade kraft pulp) with batchwise conversion. The PFs were successfully stabilized and carbonized continuously over a total time of 1.0-1.5 h, comparable to the industrial production of CFs from polyacrylonitrile. CFs derived continuously at 1000 °C with a relative stretch of -10% (fiber contraction) had a conversion yield of 29 wt %, a diameter of 12-15 μm, a Young's modulus of 46-51 GPa, and a tensile strength of 710-920 MPa. In comparison, CFs obtained at 1000 °C via batchwise conversion (12-15 μm diameter) with a relative stretch of 0% and a conversion time of 7 h (due to the low heating and cooling rates) had a higher conversion yield of 34 wt %, a higher Young's modulus (63-67 GPa) but a similar tensile strength (800-920 MPa). This suggests that the Young's modulus can be improved by the optimization of the fiber tension, residence time, and temperature profile during continuous conversion, while a higher tensile strength can be achieved by reducing the fiber diameter as it minimizes the risk of critical defects.

| S-EPMC9118265 | biostudies-literature

Structural Effects of Cellulose on Hydrolysis and Carbonization Behavior during Hydrothermal Treatment.

Project description:This study aims to investigate how the morphology of cellulose influences the hydrolysis and carbonization during hydrothermal treatment at temperatures between 180 and 240 °C. The morphology of cellulose, especially different crystallinities and degrees of polymerization, is represented by microcrystalline cellulose and α-cellulose. Kinetic analysis is considered a tool to allow the determination of the mechanisms of the two types of cellulose during the hydrothermal process. A kinetic model, in which cellulose is assumed to be hydrolyzed to a limited extent, is proposed. Five scenarios are used as models for pyrolysis of nonhydrolyzed cellulose that forms primary char, along with reaction pathways of hydrolyzable cellulose and its derivatives that latterly form secondary char. The morphologies of solid products are in good agreement with the results of the proposed model.

| S-EPMC7271358 | biostudies-literature

Tuning the Properties of Iron-Doped Porous Graphitic Carbon Synthesized by Hydrothermal Carbonization of Cellulose and Subsequent Pyrolysis.

Project description:The applied pyrolysis temperature was found to strongly affect composition, structure, and oxidation behavior of pure and iron oxide nanoparticle (NP)-loaded carbon materials originating from hydrothermal carbonization (HTC) of cellulose. A strong loss of functional groups during pyrolysis at temperatures beyond 300 °C of the HTC-derived hydrochars was observed, resulting in an increase of the carbon content up to 95 wt% for the carbon materials pyrolyzed at 800 °C and an increase of the specific surface area with a maximum of 520 m2 g-1 at a pyrolysis temperature of 600 °C. Devolatilization mainly took place in the range from 300 to 500 °C, releasing light pyrolysis gases such as CO, CO2, H2O and larger oxygen-containing molecules up to C11. The presence of iron oxide NPs lowered the specific surface areas by about 200 m2 g-1 and resulted in the formation of mesopores. For the iron oxide-containing composites pyrolyzed up to 500 °C, the oxidation temperature was decreased by about 100 °C, indicating tight contact between the iron oxide NPs and the carbon matrix. For higher pyrolysis temperatures, this catalytic effect of iron oxide on carbon oxidation vanished due to carbothermal reduction to iron and iron carbide, which, however, catalyzed the graphitization of the carbon matrix. Thus, the well-controlled two-step synthesis based on a biomass-derived precursor yielded stably embedded iron NPs in a corrosion-resistant graphitic carbon matrix.

| S-EPMC6648909 | biostudies-literature

Anomalous tensile response of bacterial cellulose nanopaper at intermediate strain rates.

Project description:Nanocellulose network in the form of cellulose nanopaper is an important material structure and its time-dependent mechanical response is crucial in many of its potential applications. In this work, we report the influences of grammage and strain rate on the tensile response of bacterial cellulose (BC) nanopaper. BC nanopaper with grammages of 20, 40, 60 and 80 g m-2 were tested in tension at strain rates ranging from 0.1% s-1 to 50% s-1. At strain rates [Formula: see text] 2.5% s-1, both the tensile modulus and strength of the BC nanopapers stayed constant at ~ 14 GPa and ~ 120 MPa, respectively. At higher strain rates of 25% s-1 and 50% s-1 however, the tensile properties of the BC nanopapers decreased significantly. This observed anomalous tensile response of BC nanopaper is attributed to inertial effect, in which some of the curled BC nanofibres within the nanopaper structure do not have enough time to uncurl before failure at such high strain rates. Our measurements further showed that BC nanopaper showed little deformation under creep, with a secondary creep rate of only ~ 10-6 s-1. This stems from the highly crystalline nature of BC, as well as the large number of contact or physical crosslinking points between adjacent BC nanofibres, further reducing the mobility of the BC nanofibres in the nanopaper structure.

| S-EPMC7498453 | biostudies-literature

Affinity to cellulose is a shared property among coiled-coil domains of intermediate filaments and prokaryotic intermediate filament-like proteins.

Project description:Coiled-coil domains of intermediate filaments (IF) and prokaryotic IF-like proteins enable oligomerisation and filamentation, and no additional function is ascribed to these coiled-coil domains. However, an IF-like protein from Streptomyces reticuli was reported to display cellulose affinity. We demonstrate that cellulose affinity is an intrinsic property of the IF-like proteins FilP and Scy and the coiled-coil protein DivIVA from the genus Streptomyces. Furthermore, IF-like proteins and DivIVA from other prokaryotic species and metazoan IF display cellulose affinity despite having little sequence homology. Cellulose affinity-based purification is utilised to isolate native FilP protein from the whole cell lysate of S. coelicolor. Moreover, cellulose affinity allowed for the isolation of IF and IF-like protein from the whole cell lysate of C. crescentus and a mouse macrophage cell line. The binding to cellulose is mediated by certain combinations of coiled-coil domains, as demornstrated for FilP and lamin. Fusions of target proteins to cellulose-binding coiled-coil domains allowed for cellulose-based protein purification. The data presented show that cellulose affinity is a novel function of certain coiled-coil domains of IF and IF-like proteins from evolutionary diverse species.

| S-EPMC6224456 | biostudies-literature

Electroreductive 5-Hydroxymethylfurfural Dimerization on Carbon Electrodes.

Project description:The electrochemical conversion of biomass-based compounds to fuels and fuel precursors can aid the defossilization of the transportation sector. Herein, the electrohydrodimerization of 5-hydroxymethylfurfural (HMF) to the fuel precursor 5,5'-bis(hydroxymethyl)hydrofuroin (BHH) was investigated on different carbon electrodes. Compared to boron-doped diamond (BDD) electrodes, on glassy carbon (GC) electrodes a less negative HMF reduction onset potential and a switch in product selectivity from BHH to the electrocatalytic hydrogenation product 2,5-di(hydroxymethyl)furan (DHMF) with increasing overpotential was found. On BDD, the electrohydrodimerization was the dominant process independent of the applied potential. An increase in the initial HMF concentration led to suppression of the competing hydrogen evolution reaction and DHMF formation, resulting in higher BHH faradaic efficiencies. In contrast, BHH selectivity decreased with higher initial HMF concentration, which was attributed to increased electrochemically induced HMF degradation. Finally, it was demonstrated that even a simple graphite foil can function as an active HMF electroreduction catalyst.

| S-EPMC9298403 | biostudies-literature

Carbonization of single polyacrylonitrile chains in coordination nanospaces.

Project description:It has been over half a century since polyacrylonitrile (PAN)-based carbon fibers were first developed. However, the mechanism of the carbonization reaction remains largely unknown. Structural evolution of PAN during the preoxidation reaction, a stabilization reaction, is one of the most complicated stages because many chemical reactions, including cyclization, dehydration, and cross-linking reactions, simultaneously take place. Here, we report the stabilization reaction of single PAN chains within the one-dimensional nanochannels of metal-organic frameworks (MOFs) to study an effect of interchain interactions on the stabilization process as well as the structure of the resulting ladder polymer (LP). The stabilization reaction of PAN within the MOFs could suppress the rapid generation of heat that initiates the self-catalyzed reaction and inevitably provokes many side-reactions and scission of PAN chains in the bulk state. Consequently, LP prepared within the MOFs had a more extended conjugated backbone than the bulk condition.

| S-EPMC8162375 | biostudies-literature

Cellulose synthase mutants

Project description:We compared the transcriptome of homozygous mutants for AtCesA4 and AtCesA6 (cellulose synthase genes) to their heterozygous counterparts that have a wild type phenotype. All plants were 4-weeks-old and grown under short day conditions.

2010-04-19 | GSE20221 | GEO

Green conversion of 5-hydroxymethylfurfural to furan-2,5-dicarboxylic acid by heterogeneous expression of 5-hydroxymethylfurfural oxidase in Pseudomonas putida S12.

Project description:Transforming petrochemical processes into bioprocesses has become an important goal of sustainable development. The chemical synthesis of 2,5-furandicarboxylic acid (FDCA) from 5-hydroxymethylfurfural (HMF) is expensive and environmentally unfavourable. The study aims to investigate a whole-cell biocatalyst for efficient biotransformation of HMF to FDCA. For the first time, a genetically engineered Pseudomonas putida S12 strain expressing 5-hydroxymethylfurfural oxidase (HMFO) was developed for the biocatalytic conversion of HMF to FDCA. This whole-cell biocatalyst produced 35.7 mM FDCA from 50 mM HMF in 24 h without notable inhibition. However, when the initial HMF concentration was elevated to 100 mM, remarkable inhibition on FDCA production was observed, resulting in a reduction of FDCA yield to 42%. We solve this substrate inhibition difficulty by increasing the inoculum density. Subsequently, we used a fed-batch strategy by maintaining low HMF concentration in the culture to maximize the final FDCA titre. Using this approach, 545 mM of FDCA was accumulatively produced after 72 hs, which is the highest production rate per unit mass of cells to the best of our knowledge.

| S-EPMC7264871 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data