High-Strength GO/PA66 Nanocomposite Fibers via In Situ Precipitation and Polymerization.
Ontology highlight
ABSTRACT:
SUBMITTER: Gu A
PROVIDER: S-EPMC8196895 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Simultaneous enhancement of conductivity and mechanical properties for polyaniline/polymer nanocomposite still remains a big challenge. Here, a reverse approach via in situ polymerization (RIP) of vinyl monomers in waterborne polyaniline dispersion was raised to prepare conductive polyaniline (GPANI)/polyacrylate (PMB) interpenetrating polymer (GPANI-PMB) nanocomposite. GPANI/PMB physical blend was simultaneously prepared as reference. The conductive GPANI-PMB nanocomposite film with compact pomegranate-shape morphology is homogeneous, ultraflexible and mechanically strong. With incorporating a considerable amount of PMB into GPANI via the RIP method, only a slight decrease from 3.21 to 2.80 S/cm was detected for the conductivity of GPANI-PMB, while the tensile strength significantly increased from 25 to 43.5 MPa, and the elongation at break increased from 40% to 234%. The water absorption of GPANI-PMB3 after 72 h immersion decreased from 24.68% to 10.35% in comparison with GPANI, which is also higher than that of GPANI/PMB. The conductivity and tensile strength of GPANI-PMB were also much higher than that of GPANI/PMB (0.006 S/cm vs. 5.59 MPa). Moreover, the conductivity of GPANI-PMB remained almost invariable after folding 200 times, while that of GPANI/PMB decreased by almost half. This RIP approach should be applicable for preparing conventional conductive polymer nanocomposite with high conductivity, high strength and high flexibility.
| S-EPMC8271515 | biostudies-literature
Project description:Electrospinning (e-spinning) is an emerging technique to prepare ultrafine fibers. Polyphenylene sulfide (PPS) is a high-performance resin which does not dissolve in any solvent at room temperature. Commercial PPS fibers are produced mainly by meltblown or spunbonded process to give fibers ~20 μm in diameter. In this research, an in-house designed melt electrospinning device was used to fabricate ultrafine PPS fibers, and the e-spinning operation conducted under inert gas to keep PPS fibers from oxidizing. Under the optimum e-spinning conditions (3 mm of nozzle diameter, 30 kV of electrostatic voltage, and 9.5 cm of tip-to-collector distance), the as-spun fibers were less than 8.0 μm in diameter. After characterization, the resultant PPS fibers showed uniform diameter and structural stability. Compared with commercial PPS staple fibers, the obtained fibers had a cold crystallization peak and 10 times higher storage modulus, thereby offering better tensile tenacity and more than 400% elongation at break.
| S-EPMC6473442 | biostudies-literature
Project description:Bio-renewable carbon fibers are fabricated and employed as high-strength composite materials in many fields. In this work, a facile and low energy consumption method was developed to fabricate high-strength lignin-based carbon fibers. Using iodine treatment, the thermodynamic stability of the lignin-based precursor fibers increased significantly, and thus energy consumption during the preparation of the carbon fibers was reduced. The influence of the iodine treatment on fibers was analyzed by differential scanning calorimetry (DSC), scanning electron microscopy (SEM), Raman spectroscopy, tension testing, etc. The resulting iodine lignin-based carbon fibers had better tensile strength (89 MPa) than that of PAN carbon fibers produced by electrospinning technology.
| S-EPMC9076998 | biostudies-literature
Project description:The production of liquid crystalline (LC) polymer particles with a narrow size distribution on a large scale remains a challenge. Here, we report the preparation of monodisperse, cross-linked liquid crystalline particles via precipitation polymerization. This versatile and scalable method yields polymer particles with a smectic liquid crystal order. Although the LC monomers are randomly dissolved in solution, the oligomers self-align and LC order is induced. For the polymerization, a smectic LC monomer mixture consisting of cross-linkers and benzoic acid hydrogen-bonded dimers is used. The average diameter of the particles increases at higher polymerization temperatures and in better solvents, whereas the monomer and initiator concentration have only minor impact on the particle size. After deprotonating of the benzoic acid groups, the particles show rapid absorption of a common cationic dye, methylene blue. The methylene blue in the particles can be subsequently released with the addition of Ca2+, while monovalent ions fail to trigger the release. These results reveal that precipitation polymerization is an attractive method to prepare functional LC polymer particles of a narrow size distribution and on a large scale.
| S-EPMC6854653 | biostudies-literature
Project description:Composite hydrogels have gained great attention as three-dimensional (3D) printing biomaterials because of their enhanced intrinsic mechanical strength and bioactivity compared to pure hydrogels. In most conventional printing methods for composite hydrogels, particles are preloaded in ink before printing, which often reduces the printability of composite ink with little mechanical improvement due to poor particle-hydrogel interaction of physical mixing. In contrast, the in situ incorporation of nanoparticles into a hydrogel during 3D printing achieves uniform distribution of particles with remarkable mechanical reinforcement, while precursors dissolved in inks do not influence the printing process. Herein, we introduced a "printing in liquid" technique coupled with a hybridization process, which allows 3D freeform printing of nanoparticle-reinforced composite hydrogels. A viscoplastic matrix for this printing system provides not only support for printed hydrogel filaments but also chemical reactants to induce various reactions in printed objects for in situ modification. Nanocomposite hydrogel scaffolds were successfully fabricated through this 3D freeform printing of hyaluronic acid (HAc)-alginate (Alg) hydrogel inks through a two-step crosslinking strategy. The first ionic crosslinking of Alg provided structural stability during printing, while the secondary crosslinking of photo-curable HAc improved the mechanical and physiological stability of the nanocomposite hydrogels. For in situ precipitation during 3D printing, phosphate ions were dissolved in the hydrogel ink and calcium ions were added to the viscoplastic matrix. The composite hydrogels demonstrated a significant improvement in mechanical strength, biostability, as well as biological performance compared to pure HAc. Moreover, the multi-material printing of composites with different calcium phosphate contents was achieved by adjusting the ionic concentration of inks. Our method greatly accelerates the 3D printing of various functional or hybridized materials with complex geometries through the design and modification of printing materials coupled with in situ post-printing functionalization and hybridization in reactive viscoplastic matrices.
| S-EPMC7415863 | biostudies-literature
Project description:Ultrafine fibers are widely employed because of their lightness, softness, and warmth retention. Although silkworm silk is one of the most applied natural silks, it is coarse and difficult to transform into ultrafine fibers. Thus, to obtain ultrafine high-performance silk fibers, we employed anti-juvenile hormones in this study to induce bimolter silkworms. We found that the bimolter cocoons were composed of densely packed thin fibers and small apertures, wherein the silk diameter was 54.9% less than that of trimolter silk. Further analysis revealed that the bimolter silk was cleaner and lighter than the control silk. In addition, it was stronger (739 MPa versus 497 MPa) and more stiffness (i.e., a higher Young's modulus) than the trimolter silk. FTIR and X-ray diffraction results revealed that the excellent mechanical properties of bimolter silk can be attributed to the higher β-sheet content and crystallinity. Chitin staining of the anterior silk gland suggested that the lumen is narrower in bimolters, which may lead to the formation of greater numbers of β-sheet structures in the silk. Therefore, this study reveals the relationship between the structures and mechanical properties of bimolter silk and provides a valuable reference for producing high-strength and ultrafine silk fibers.
| S-EPMC7693878 | biostudies-literature
Project description:The nanofiller reinforcing effect in nanocomposites is often far below the theoretically predicted values, largely because of the poor interfacial interaction between the nanofillers and matrix. Here, we report that graphene-wrapped B4C nanowires (B4C-NWs@graphene) empowered exceptional dispersion of nanowires in matrix and superlative nanowire-matrix bonding. The 0.2 volume % B4C-NWs@graphene reinforced epoxy composite exhibited simultaneous enhancements in strength (144.2 MPa), elastic modulus (3.5 GPa), and ductility (15%). Tailoring the composite interfaces with graphene enabled effective utilization of the nanofillers, resulting in two times increase in load transfer efficiency. Molecular dynamics simulations unlocked the shear mixing graphene/nanowire self-assembly mechanism. This low-cost yet effective technique presents unprecedented opportunities for improving nanocomposite interfaces, enabling high load transfer efficiency, and opens up a new path for developing strong and tough nanocomposites.
| S-EPMC7556841 | biostudies-literature
Project description:Poly(N-isopropylacrylamide) microgels have found various uses in fundamental polymer and colloid science as well as in different applications. They are conveniently prepared by precipitation polymerization. In this reaction, radical polymerization and colloidal stabilization interact with each other to produce well-defined thermosensitive particles of narrow size distribution. However, the underlying mechanism of precipitation polymerization has not been fully understood. In particular, the crucial early stages of microgel formation have been poorly investigated so far. In this contribution, we have used small-angle neutron scattering in conjunction with a stopped-flow device to monitor the particle growth during precipitation polymerization in situ. The average particle volume growth is found to follow pseudo-first order kinetics, indicating that the polymerization rate is determined by the availability of the unreacted monomer, as the initiator concentration does not change considerably during the reaction. This is confirmed by calorimetric investigation of the polymerization process. Peroxide initiator-induced self-crosslinking of N-isopropylacrylamide and the use of the bifunctional crosslinker N,N'-methylenebisacrylamide are shown to decrease the particle number density in the batch. The results of the in situ small-angle neutron scattering measurements indicate that the particles form at an early stage in the reaction and their number density remains approximately the same thereafter. The overall reaction rate is found to be sensitive to monomer and initiator concentration in accordance with a radical solution polymerization mechanism, supporting the results from our earlier studies.
| S-EPMC6648459 | biostudies-literature
Project description:An efficient strategy for growing thermo-sensitive polymers from the surface of exfoliated graphene oxide (GO) is reported in this article. GO sheets with hydroxyls and epoxy groups on the surface were first prepared by modified Hummer's method. Epoxy groups on GO sheets can be easily modified through ring-opening reactions, involving nucleophilic attack by tris(hydroxymethyl) aminomethane (TRIS). The resulting GO-TRIS sheets became a more versatile precursor for next ring opening polymerization (ROP) of ethyl ethylene phosphate (EEP), leading to GO-TRIS/poly(ethyl ethylene phosphate) (GO-TRIS-PEEP) nanocomposite. The nanocomposite was characterized by ¹H NMR, Fourier transform infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS), thermogravimetric analysis (TGA), differential thermal gravity (DTG), transmission electron microscopy (TEM) and atomic force microscopy (AFM). Since hydrophilic PEEP chains make the composite separate into single layers through hydrogen bonding interaction, the dispersity of the functionalized GO sheets in water is significantly improved. Meanwhile, the aqueous dispersion of GO-TRIS-PEEP nanocomposite shows reversible temperature switching self-assembly and disassembly behavior. Such a smart graphene oxide-based hybrid material is promising for applications in the biomedical field.
| S-EPMC6409759 | biostudies-literature
Project description:Because of their attractive mechanical properties, conducting polymers are widely perceived as materials of choice for wearable electronics and electronic textiles. However, most state-of-the-art conducting polymers contain harmful dopants and are only processable from solution but not in bulk, restricting the design possibilities for applications that require conducting micro-to-millimeter scale structures, such as textile fibers or thermoelectric modules. In this work, we present a strategy based on melt processing that enables the fabrication of nonhazardous, all-polymer conducting bulk structures composed of poly(3,4-ethylenedioxythiophene) (PEDOT) polymerized within a Nafion template. Importantly, we employ classical polymer processing techniques including melt extrusion followed by fiber spinning or fused filament 3D printing, which cannot be implemented with the majority of doped polymers. To demonstrate the versatility of our approach, we fabricated melt-spun PEDOT:Nafion fibers, which are highly flexible, retain their conductivity of about 3 S cm-1 upon stretching to 100% elongation, and can be used to construct organic electrochemical transistors (OECTs). Furthermore, we demonstrate the precise 3D printing of complex conducting structures from OECTs to centimeter-sized PEDOT:Nafion figurines and millimeter-thick 100-leg thermoelectric modules on textile substrates. Thus, our strategy opens up new possibilities for the design of conducting, all-polymer bulk structures and the development of wearable electronics and electronic textiles.
| S-EPMC7033659 | biostudies-literature