Numerical Approach for the Assessment of Micro-Textured Walls Effects on Rubber Injection Moulding.
Ontology highlight
ABSTRACT:
SUBMITTER: Garcia-Camprubi M
PROVIDER: S-EPMC8198524 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Background: Micro-texturing is an increasingly used technique that aims at improving the functional behaviour of components during their useful life, and it is applied in different industrial manufacturing processes for different purposes, such as reducing friction on dynamic rubber seals for pneumatic equipment, among others. Micro-texturing is produced on polymer components by transfer from the mould and might critically increase the adhesion and friction between the moulded rubber part with the mould, provoking issues during demoulding, both on the mould itself and on the rubber part. The mould design, the coating release agent applied to the mould surface, and the operational parameters of the moulding/demoulding process, are fundamental aspects to avoid problems and guarantee a correct texture transfer during the demoulding process. Methods: In this work, the lack of knowledge about demoulding processes was addressed with an in-house test rig and a robust experimental procedure to measure demoulding forces (DFs) as well as the final quality of the moulded part, between thermoset polymers and moulds. After the characterization of several Sol-Gel coating formulations (inorganic; hybrid) the influence of several parameters was analysed experimentally, i.e.: Sol-Gel efficiency, texture effects, pattern geometry, roughness and material compound. Results: The results obtained from the experimental studies revealed that texture depth is the most critical geometrical parameter, showing high scatter among the selected compounds. Finally, the experimental results were used to compute a model through reduced order modelling (ROM) technique for the prediction of DFs. Conclusions: The characterization of DFs in a laboratory, with a specific device operated by a universal testing machine (UTM), provided valuable information that allows a fast and optimized introduction of texturing in rubber components. Selection of a novel Sol-Gel coating and the use of the ROM technique contributed to speed up implementation for mass production.
| S-EPMC10446097 | biostudies-literature
Project description:The high production rate of conventional plastics and their low degradability result in severe environmental problems, such as plastic accumulation and some other related consequences. One alternative to these materials is the production of oil-free bioplastics, based on wastes from the agro-food industry, which are biodegradable. Not only is rice bran an abundant and non-expensive waste, but it is also attractive due to its high protein and starch content, which can be used as macromolecules for bioplastic production. The objective of this work was to develop rice-bran-based bioplastics by injection moulding. For this purpose, this raw material was mixed with a plasticizer (glycerol), analysing the effect of three mould temperatures (100, 130 and 150 °C) on the mechanical and microstructural properties and water absorption capacity of the final matrices. The obtained results show that rice bran is a suitable raw material for the development of bioplastics whose properties are strongly influenced by the processing conditions. Thus, higher temperatures produce stiffer and more resistant materials (Young's modulus improves from 12 ± 7 MPa to 23 ± 6 and 33 ± 6 MPa when the temperature increases from 100 to 130 and 150 °C, respectively); however, these materials are highly compact and, consequently, their water absorption capacity diminishes. On the other hand, although lower mould temperatures lead to materials with lower mechanical properties, they exhibit a less compact structure, resulting in enhanced water absorption capacity.
| S-EPMC7866207 | biostudies-literature
Project description:Biocompatible titanium scaffolds with up to 40% interconnected porosity were manufactured through the metal injection moulding process and the space holder technique. The mechanical properties of the manufactured scaffold showed a high level of compatibility with those of the cortical human bone. Sintering at 1250 °C produced scaffolds with 36% porosity and more than 90% interconnected pores, a compressive yield stress of 220 MPa and a Young's modulus of 7.80 GPa, all suitable for bone tissue engineering. Increasing the sintering temperature to 1300 °C increased the Young's modulus to 22.0 GPa due to reduced porosity, while reducing the sintering temperature to 1150 °C lowered the yield stress to 120 MPa, indicative of insufficient sintering. Electrochemical studies revealed that samples sintered at 1150 °C have a higher corrosion rate compared with those at a sintering temperature of 1250 °C. Overall, it was concluded that sintering at 1250 °C yielded the most desirable results.
| S-EPMC6163891 | biostudies-other
Project description:It is well known that block copolymers with cylindrical morphology show alignment with shear, resulting in anisotropic mechanical properties. Here we show that well-ordered bi-directional orientation can be achieved in such materials by slow injection moulding. This results in a microstructure, and anisotropic mechanical properties, similar to many natural tissues, making this method attractive for engineering prosthetic fibrous tissues. An application of particular interest to us is prosthetic polymeric heart valve leaflets, mimicking the shape, microstructure and hence performance of the native valve. Anisotropic layers have been observed for cylinder-forming block copolymers centrally injected into thin circular discs. The skin layers exhibit orientation parallel to the flow direction, whilst the core layer shows perpendicularly oriented domains; the balance of skin to core layers can be controlled by processing parameters such as temperature and injection rate. Heart valve leaflets with a similar layered structure have been prepared by injection moulding. Numerical modelling demonstrates that such complex orientation can be explained and predicted by the balance of shear and extensional flow.
| S-EPMC4439735 | biostudies-literature
Project description:The in-plane seismic behavior of unreinforced masonry (URM) structures is closely related to the aspect ratio of the wall and vertical load. The purpose of this study was to investigate the difference between the failure mode of the model and the horizontal load using the finite element model (FEM) under the action of aspect ratio (0.50 to 2.00) and vertical load (0.2 MPa to 0.70 MPa). The overall macro model was established using the Abaqus software, and the corresponding simulation was performed. The simulation results indicate that: i) the shear failure and flexural failure were the main failure modes of masonry walls; ii) shear failure could be viewed as the main failure mode of the model when the aspect ratio was less than 1.00; however, the flexural failure was considered to be the main failure mode of the model once the aspect ratio was greater than 1.00; iii) when a vertical load of 0.20 MPa was applied to the model, only flexural failure was observed, regardless of whether the aspect ratio of the model increased or decreased; the flexural shear mixed failure was captured within the range of 0.30 MPa- 0.50 MPa; the shear failure was the main failure mode within the range of 0.60 MPa- 0.70 MPa; and iv) the wall with an aspect ratio less than 1.00 could bear a higher horizontal load, and the increase in vertical load can significantly improve the horizontal load of the wall. In contrast, once the aspect ratio of the wall reaches or exceeds 1.00, the increase in the vertical load has little effect on the increase in the horizontal load of the wall.
| S-EPMC9980798 | biostudies-literature
Project description:This paper presents a pioneering effort to ascertain the suitability of hyperelastic modelling in simulating the stress-strain response of oil palm shell reinforced rubber (ROPS) composites. ROPS composites with different oil palm shell contents (0%, 5%, 10% and 20% by volume) were cast in the laboratory for the experimental investigation. ROPS specimens with circular, square, hexagon, and octagon shapes (loading surface) were considered to evaluate the accuracy of finite element simulation considering the shape effect of composites. Strain-controlled (compressive) tests with ? ? 50% at 0.8 Hz frequency were conducted in the laboratory and the test data obtained was used as input to simulate material coefficients corresponding to the strain energy functions chosen. Five different strain energy functions were selected and utilized for the hyperelastic modelling in this study using finite element approach. The shape effect was then used to ascertain any variation in the simulation outcomes and to discuss the effect of shape on the behaviour of ROPS composites in comparison to existing literature. The numerical predictions using the Yeoh model (error ? 2.7% for circular shaped ROPS) were found to perform best in comparison with the experimental results, thus a more stable and suitable hyperelastic model to this end. The Marlow (error ? 4.6% for circular shaped ROPS) and Arruda Boyce (error ? 4.7% for circular shaped ROPS) models were amongst the next alternatives to perform better. Even with the other shapes considered in this study, Yeoh, followed by the Marlow function, were more appropriate models. The shape effect was then studied with particular emphasis on comparing and assessing them with that observed in the literature. To this end, adopting the Yeoh function in the finite element model is the ideal approach to estimate the stress-strain response of ROPS composites.
| S-EPMC7077467 | biostudies-literature
Project description:Nano- and microstructured titanium surfaces have recently attracted attention in the field of regenerative medicine because of the influence which surface characteristics such as roughness and wettability can have on cellular processes. This study focuses on the correlation of surface properties (wettability and nano/micro texture) of laser-structured Ti6Al4V samples with pronounced cell adhesion. Samples were structured with multiple laser parameters in order to create a range of surface properties. Surface characterization was performed by contact angle measurements 1 and 7 days after laser processing. The arithmetic mean roughness of the material surface in an area (Sa) was determined by means of confocal laser scanning microscopy (CLSM). Immediately after wettability tests of the laser-structured surfaces, in vitro experiments with human MG-63 osteoblasts were carried out. For this purpose, the cell morphology and actin cytoskeleton organization were analyzed using CLSM and scanning electron microscopy. On rough microstructures with deep cavities, the cell growth and spreading were inhibited. An improved cellular adhesion and growth on nanostructured and sinusoidal microstructured surfaces could be demonstrated, regardless of hydrophilicity of the surfaces.
| S-EPMC6650973 | biostudies-literature
Project description:A river water quality spatial profile has a diverse pattern of variation over different climatic regions. To comprehend this phenomenon, our study evaluated the spatial scale variation of the Water Quality Index (WQI). The study was carried out over four main climatic classes in Asia based on the Koppen-Geiger climate classification system: tropical, temperate, cold, and arid. The one-dimensional surface water quality model, QUAL2Kw was selected and compared for water quality simulations. Calibration and validation were separately performed for the model predictions over different climate classes. The accuracy of the water quality model was assessed using different statistical analyses. The spatial profile of WQI was calculated using model predictions based on dissolved oxygen (DO), biological oxygen demand (BOD), nitrate (NO3), and pH. The results showed that there is a smaller longitudinal variation of WQI in the cold climatic regions than other regions, which does not change the status of WQI. Streams from arid, temperate, and tropical climatic regions show a decreasing trend of DO with respect to the longitudinal profiles of main river flows. Since this study found that each climate zone has the different impact on DO dynamics such as reaeration rate, reoxygenation, and oxygen solubility. The outcomes obtained in this study are expected to provide the impetus for developing a strategy for the viable improvement of the water environment.
| S-EPMC6209875 | biostudies-other
Project description:Flexible polymers such as poly dimethyl siloxane (PDMS) can be patterned at the micro- and nanoscale by casting, for a variety of applications. This replication-based fabrication process is relatively cheap and fast, yet injection molding offers an even faster and cheaper alternative to PDMS casting, provided thermoplastic polymers with similar mechanical properties can be used. In this paper, a thermoplastic polyurethane is evaluated for its patterning ability with an aim to forming the type of flexible structures used to measure and modulate the contractile forces of cells in tissue engineering experiments. The successful replication of grating structures is demonstrated with feature sizes as low as 100 nm and an analysis of certain processing conditions that facilitate and enhance the accuracy of this replication is presented. The results are benchmarked against an optical storage media grade polycarbonate.
| S-EPMC6563430 | biostudies-literature