Browse
Submit Data
Databases
API
Help

Dataset Information

32 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Tantalum-Doped TiO₂ Prepared by Atomic Layer Deposition and Its Application in Perovskite Solar Cells.

ABSTRACT: Tantalum (Ta)-doped titanium oxide (TiO₂) thin films are grown by plasma enhanced atomic layer deposition (PEALD), and used as both an electron transport layer and hole blocking compact layer of perovskite solar cells. The metal precursors of tantalum ethoxide and titanium isopropoxide are simultaneously injected into the deposition chamber. The Ta content is controlled by the temperature of the metal precursors. The experimental results show that the Ta incorporation introduces oxygen vacancies defects, accompanied by the reduced crystallinity and optical band gap. The PEALD Ta-doped films show a resistivity three orders of magnitude lower than undoped TiO₂, even at a low Ta content (0.8-0.95 at.%). The ultraviolet photoelectron spectroscopy spectra reveal that Ta incorporation leads to a down shift of valance band and conduction positions, and this is helpful for the applications involving band alignment engineering. Finally, the perovskite solar cell with Ta-doped TiO₂ electron transport layer demonstrates significantly improved fill factor and conversion efficiency as compared to that with the undoped TiO₂ layer.

SUBMITTER: Hsu CH

PROVIDER: S-EPMC8226548 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Photocatalytic and Gas Sensitive Multiwalled Carbon Nanotube/TiO2-ZnO and ZnO-TiO2 Composites Prepared by Atomic Layer Deposition.

Project description:TiO2 and ZnO single and multilayers were deposited on hydroxyl functionalized multi-walled carbon nanotubes using atomic layer deposition. The bare carbon nanotubes and the resulting heterostructures were characterized by TG/DTA, Raman, XRD, SEM-EDX, XPS, TEM-EELS-SAED and low temperature nitrogen adsorption techniques, and their photocatalytic and gas sensing activities were also studied. The carbon nanotubes (CNTs) were uniformly covered with anatase TiO2 and wurtzite ZnO layers and with their combinations. In the photocatalytic degradation of methyl orange, the most beneficial structures are those where ZnO is the external layer, both in the case of single and double oxide layer covered CNTs (CNT-ZnO and CNT-TiO2-ZnO). The samples with multilayer oxides (CNT-ZnO-TiO2 and CNT-TiO2-ZnO) have lower catalytic activity due to their larger average densities, and consequently lower surface areas, compared to single oxide layer coated CNTs (CNT-ZnO and CNT-TiO2). In contrast, in gas sensing it is advantageous to have TiO2 as the outer layer. Since ZnO has higher conductivity, its gas sensing signals are lower when reacting with NH3 gas. The double oxide layer samples have higher resistivity, and hence a larger gas sensing response than their single oxide layer counterparts.

| S-EPMC7075193 | biostudies-literature

Direct deposition of Sn-doped CsPbBr<sub>3</sub> perovskite for efficient solar cell application.

Project description:All inorganic carbon-based planar perovskites, particularly CsPbBr3, have attracted considerable attention due to their excellent stability against oxygen, moisture, and heat for photovoltaic utilization. However, the power conversion efficiency of carbon-based planar CsPbBr3 perovskite solar cells is mostly low, primarily because of the inferior film quality with undesirable crystallization and narrow light absorbance ranges. Herein, we develop a novel direct deposition approach combined with Sn doping to achieve highly efficient and stable carbon-based Sn-doped CsPbBr3 perovskite solar cells. Mass-scale Sn ion-doped CsPbBr3 perovskite powder was effectively synthesized and characterized via a facile strategy by adding hydrohalic acid in the CsBr, PbBr2 and SnBr2 precursor in a dimethyl sulfoxide solution. Moreover, using the as-synthesized CsPbBr3 and Sn-doped CsPbBr3 perovskite powder, PSCs were obtained via effective direct thermal evaporation. A smooth, constant and pinhole-free perovskite film was achieved with a configuration of FTO/TiO2/Sn:CsPbBr3/carbon. PSCs based on Sn:CsPbBr3 as an absorber and carbon as the HTM achieved an impressive power conversion efficiency of 8.95% compared to 6.87% for undoped CsPbBr3; moreover, it displayed admirable stability in an open-air atmosphere for an operational period of about 720 h without a noticeable negative result. The introduction of the Sn ion may advance the interface extraction of charge between the electric transport layer to the absorber layer and absorber to the carbon electrode. Accordingly, the Sn ion doping on CsPbBr3 during the synthesis phase and the direct evaporation paves a novel approach for intended photovoltaic applications.

| S-EPMC8694008 | biostudies-literature

Single-administration, thermostable human papillomavirus vaccines prepared with atomic layer deposition technology.

Project description:Cold-chain requirements affect worldwide distribution of many vaccines. In addition, vaccines requiring multiple doses impose logistical and financial burdens, as well as patient compliance barriers. To address such limitations, we have developed new technologies to prepare thermostable, single-shot, prime-boost microparticle vaccines. Antigen/adjuvant formulations containing glass-forming polymers and trehalose first are spray-dried to form glassy microparticles that confer thermostability. Atomic layer deposition (ALD) reactions conducted in fluidized beds are then used to coat the microparticles with defined numbers of molecular layers of alumina that modulate the timed release of the internalized antigen and act as adjuvants. We have used a model HPV16 L1 capsomere antigen to evaluate the properties of these technologies. Thermostabilized powders containing HPV16 L1 capsomeres were prepared by spray-drying, coated by ALD with up to 500 molecular layers of alumina, and injected into mice. Antigen distribution was assessed by live-animal IR dye tracking of injected labeled antigen. Antibody responses were measured weekly by ELISA, and neutralizing antibodies were measured by pseudovirus neutralization assays at selected time points. Thermostability was evaluated by measuring antibody responses after incubating ALD-coated antigen powders for one month at 50 °C. Single doses of the ALD-coated vaccine formulations elicited a prime-boost immune response, and produced neutralizing responses and antibody titers that were equivalent or superior to conventional prime-boost doses of liquid formulations. Antibody titers were unaffected by month-long incubation of the formulations at 50 °C. Single-dose, thermostable antigen preparations may overcome current limitations in HPV vaccine delivery as well as being widely applicable to other antigens.

| S-EPMC7265342 | biostudies-literature

Growth Temperature Influence on Atomic-Layer-Deposited In2O3 Thin Films and Their Application in Inorganic Perovskite Solar Cells.

Project description:Recently, indium oxide (In2O3) thin films have emerged as a promising electron transport layer (ETL) for perovskite solar cells; however, solution-processed In2O3 ETL suffered from poor morphology, pinholes, and required annealing at high temperatures. This research aims to carry out and prepare pinhole-free, transparent, and highly conductive In2O3 thin films via atomic layer deposition (ALD) seizing efficiently as an ETL. In order to explore the growth-temperature-dependent properties of In2O3 thin film, it was fabricated by ALD using the triethyl indium (Et3In) precursor. The detail of the ALD process at 115-250 °C was studied through the film growth rate, crystal structure, morphology, composition, and optical and electrical properties. The film growth rate increased from 0.009 nm/cycle to 0.088 nm/cycle as the growth temperature rose from 115 °C to 250 °C. The film thickness was highly uniform, and the surface roughness was below 1.6 nm. Our results confirmed that film's structural, optical and electrical properties directly depend on film growth temperature. Film grown at ≥200 °C exhibited a polycrystalline cubic structure with almost negligible carbon impurities. Finally, the device ALD-In2O3 film deposited at 250 °C exhibited a power conversion efficiency of 10.97% superior to other conditions and general SnO2 ETL.

| S-EPMC8399107 | biostudies-literature

Improved Reproducibility of PbS Colloidal Quantum Dots Solar Cells Using Atomic Layer-Deposited TiO2.

Project description:Thanks to their broadly tunable bandgap and strong absorption, colloidal lead chalcogenide quantum dots (QDs) are highly appealing as solution-processable active layers for third-generation solar cells. However, the modest reproducibility of this kind of solar cell is a pertinent issue, which inhibits the exploitation of this material class in optoelectronics. This issue is not necessarily imputable to the active layer but may originate from different constituents of the device structure. Herein, the deposition of TiO2 electron transport layer is focused on. Atomic layer deposition (ALD) greatly improves the reproducibility of PbS QD solar cells compared with the previously optimized sol-gel (SG) approach. Power conversion efficiency (PCE) of the solar cells using atomic layer-deposited TiO2 lies in the range between 5.5% and 7.2%, whereas solar cells with SG TiO2 have PCE ranging from 0.5% to 6.9% with a large portion of short-circuited devices. Investigations of TiO2 layers by atomic force microscopy and scanning electron microscopy reveal that these films have very different surface morphologies. Whereas the TiO2 films prepared by SG synthesis and deposited by spin coating are very smooth, TiO2 films made by ALD repeat the surface texture of the fluorine-doped tin oxide (FTO) substrate underneath.

| S-EPMC7006825 | biostudies-literature

High-Performance Core/Shell of ZnO/TiO2 Nanowire with AgCl-Doped CdSe Quantum Dots Arrays as Electron Transport Layer for Perovskite Solar Cells.

Project description:Most previous studies of perovskite core/shell structures have been based on ZnO/TiO2 nanowires (NWs), which are not suitable for high photoelectric conversion efficiency. Here, core/shell ZnO/TiO2 NWs with AgCl-doped CdSe quantum dots were fabricated as an electron transport layer (ETL) for perovskite solar cells, based on ZnO/TiO2 arrays. We designed CdSe with AgCl dopants that were synthesized by a colloidal process. An improvement of the recombination barrier (Rct1), due to shell supplementation with AgCl-doped CdSe quantum dots, improved the open circuit voltage, the fill factor, and the adsorption capacity of CH3NH3PbI3 perovskite with NWs. The enhanced cell steady state was attributable to TiO2 with AgCl-doped CdSe QD supplementation. A maximum power conversion efficiency of 15.12% was attained in an atmospheric environment. The mechanism of the recombination and electron transport in the perovskite solar cells becoming the basis of ZnO/TiO2 core/shell arrays was investigated to represent the merit of ZnO/TiO2 core/shell arrays as an electron transport layer in effective devices. These results showed an uncomplicated approach for restraining non-radiative recombination loss in hetero-structure core/shell arrays to significantly improve perovskite solar cell performance and increase the effectiveness of photovoltaics.

| S-EPMC7504724 | biostudies-literature

Radio Frequency Magnetron Sputtering Deposition of TiO2 Thin Films and Their Perovskite Solar Cell Applications.

Project description:In this work, we report a physical deposition based, compact (cp) layer synthesis for planar heterojunction perovskite solar cells. Typical solution-based synthesis of cp layer for perovskite solar cells involves low-quality of thin films, high-temperature annealing, non-flexible devices, limitation of large-scale production and that the effects of the cp layer on carrier transport have not been fully understood. In this research, using radio frequency magnetron sputtering (RFMS), TiO2 cp layers were fabricated and the thickness could be controlled by deposition time; CH3NH3PbI3 films were prepared by evaporation &immersion (E &I) method, in which PbI2 films made by thermal evaporation technique were immersed in CH3NH3I solution. The devices exhibit power conversion efficiency (PCE) of 12.1% and the photovoltaic performance can maintain 77% of its initial PCE after 1440 h. The method developed in this study has the capability of fabricating large active area devices (40 × 40 mm(2)) showing a promising PCE of 4.8%. Low temperature and flexible devices were realized and a PCE of 8.9% was obtained on the PET/ITO substrates. These approaches could be used in thin film based solar cells which require high-quality films leading to reduced fabrication cost and improved device performance.

| S-EPMC4668551 | biostudies-literature

Photocatalytic hollow TiO<sub>2</sub> and ZnO nanospheres prepared by atomic layer deposition.

Project description:Carbon nanospheres (CNSs) were prepared by hydrothermal synthesis, and coated with TiO2 and ZnO nanofilms by atomic layer deposition. Subsequently, through burning out the carbon core templates hollow metal oxide nanospheres were obtained. The substrates, the carbon-metal oxide composites and the hollow nanospheres were characterized with TG/DTA-MS, FTIR, Raman, XRD, SEM-EDX, TEM-SAED and their photocatalytic activity was also investigated. The results indicate that CNSs are not beneficial for photocatalysis, but the crystalline hollow metal oxide nanospheres have considerable photocatalytic activity.

| S-EPMC5489517 | biostudies-literature

Particle atomic layer deposition.

Project description:The functionalization of fine primary particles by atomic layer deposition (particle ALD) provides for nearly perfect nanothick films to be deposited conformally on both external and internal particle surfaces, including nanoparticle surfaces. Film thickness is easily controlled from several angstroms to nanometers by the number of self-limiting surface reactions that are carried out sequentially. Films can be continuous or semi-continuous. This review starts with a short early history of particle ALD. The discussion includes agitated reactor processing, both atomic and molecular layer deposition (MLD), coating of both inorganic and polymer particles, nanoparticles, and nanotubes. A number of applications are presented, and a path forward, including likely near-term commercial products, is given.

| S-EPMC6320374 | biostudies-literature

An efficient, flexible perovskite solar module exceeding 8% prepared with an ultrafast PbI2 deposition rate.

Project description:Large-area, pinhole-free CH3NH3PbI3 perovskite thin films were successfully fabricated on 5?cm?×?5?cm flexible indium tin oxide coated polyethylene naphthalate (ITO-PEN) substrates through a sequential evaporation/spin-coating deposition method in this research. The influence of the rate-controlled evaporation of PbI2 films on the quality of the perovskite layer and the final performance of the planar-structured perovskite solar cells were investigated. An ultrafast evaporation rate of 20?Å?s-1 was found to be most beneficial for the conversion of PbI2 to CH3NH3PbI3 perovskite. Based on this high-quality CH3NH3PbI3 film, a resultant flexible perovskite solar sub-module (active area of 16?cm2) with a power conversion efficiency of more than 8% and a 1.2?cm2 flexible perovskite solar cell with a power conversion efficiency of 12.7% were obtained.

| S-EPMC5765045 | biostudies-literature