Anisotropic Carbon Nanotube Structures with High Aspect Ratio Nanopores for Li-Ion Battery Anodes.
Ontology highlight
ABSTRACT:
SUBMITTER: Jessl S
PROVIDER: S-EPMC8240089 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Amorphous silicon nanoparticles were synthesized through pyrolysis of silane gas at temperatures ranging from 575 to 675 °C. According to the used temperature and silane concentration, two distinct types of particles can be obtained: at 625 °C, spherical particles with smooth surface and a low degree of aggregation, but at a higher temperature (650 °C) and lower silane concentration, particles with extremely rough surfaces and high degree of aggregation are found. This demonstrates the importance of the synthesis temperature on the morphology of silicon particles. The two types of silicon nanoparticles were subsequently used as active materials in a lithium half cell configuration, using LiPF6 in an alkylcarbonate-based electrolyte, in order to investigate the impact of the particles morphology on the cycling performances of silicon anode material. The difference in morphology of the particles resulted in different volume expansions, which impacts the solid electrolyte interface (SEI) formation and, as a consequence, the lifetime of the electrode. Half-cells fabricated from spherical particles demonstrated almost 70% capacity retention for over 300 cycles, while the cells made from the rough, aggregated particles showed a sharp decrease in capacity after the 20th cycle. The cycling results underline the importance of Si particle engineering and its influence on the lifetime of Si-based materials.
| S-EPMC9417716 | biostudies-literature
Project description:Phosphorus (P) possesses the highest theoretical specific capacity (865 mA h g-1) among all the elements for potassium-ion battery (PIB) anodes. Although Red P (RP) has intrinsic advantages over its allotropes, including low cost and nontoxicity, and simpler preparation, it is yet unknown to effectively activate it into a high-performance PIB anode. Here, high-performance RP PIB anodes are reported. Two important factors are found to facilitate RP react with K-ions reversibly: i) nanoscale RP particles are dispersed evenly in a conductive carbon matrix composed of multiwall carbon nanotubes and Ketjen black that provide an efficient electrical pathway and a tough scaffold. ii) The results of X-ray photoelectron spectroscopy spectrum and the electrochemical performance perhaps show that no P-C bond formation is beneficial to allow K-ions to react with RP effectively. As a result, the RP/C electrodes deliver a reversible specific capacity of ?750 mA h g-1 and exhibit a high-rate capability (?300 mA h g-1 at 1000 mA g-1). RP/C full cells using potassium manganese hexacyanoferrate as cathode show a long cycling life (680 cycles) at a current density of 1000 mA g-1, in addition, a pouch-type battery is built to demonstrate practical applications.
| S-EPMC6498114 | biostudies-literature
Project description:The recovery of useful materials from earth-abundant substances is of strategic importance for industrial processes. Despite the fact that Si is the second most abundant element in the Earth's crust, processes to form Si nanomaterials is usually complex, costly and energy-intensive. Here we show that pure Si nanoparticles (SiNPs) can be derived directly from rice husks (RHs), an abundant agricultural byproduct produced at a rate of 1.2 × 10(8) tons/year, with a conversion yield as high as 5% by mass. And owing to their small size (10-40 nm) and porous nature, these recovered SiNPs exhibits high performance as Li-ion battery anodes, with high reversible capacity (2,790 mA h g(-1), seven times greater than graphite anodes) and long cycle life (86% capacity retention over 300 cycles). Using RHs as the raw material source, overall energy-efficient, green, and large scale synthesis of low-cost and functional Si nanomaterials is possible.
| S-EPMC3665957 | biostudies-literature
Project description:Resistive interfaces within the electrodes limit the energy and power densities of a battery, for example, a Li-ion battery (LIB). Typically, active materials are mixed with conductive additives in organic solvents to form a slurry, which is then coated on current collectors (e.g., bare or carbon-coated Al foils) to reduce the inherent resistance of the active material. Although many approaches using nanomaterials to either replace Al foils or improve conductivity within the active materials have been previously demonstrated, the resistance at the current collector active material interface (CCAMI), a key factor for enhancing the energy and power densities, remains unaddressed. We show that carbon nanotubes (CNTs), either directly grown or spray-coated on Al foils, are highly effective in reducing the CCAMI resistance of traditional LIB cathode materials (LiFePO4 or LFP and LiNi0.33Co0.33Mn0.33O2 or NMC). Moreover, the CNT coatings displace the need for currently used toxic organic solvents (e.g., N-methyl-2-pyrrolidone) by providing capillary channels, which improve the wetting of aqueous dispersions containing active materials. The vertically aligned CNT-coated electrodes exhibited energy densities as high as (1) ∼500 W h kg-1 at ∼170 W kg-1 for LFP and (2) ∼760 W h kg-1 at ∼570 W kg-1 for NMC. The LIBs with CCAMI-engineered electrodes withstood discharge rates as high as 600 mA g-1 for 500 cycles in the case of LFP, where commercial electrodes failed. The CNT-based CCAMI engineering approach is versatile with wide applicability to improve the performance of even textured active materials for both cathodes and anodes.
| S-EPMC6641605 | biostudies-literature
Project description:To remit capacity fading of lithium ion battery (LIB) anodes, freestanding yucca fern shaped CuO nanowires (NWs) on Cu foams are fabricated as anodes by combining facile and scalable anodization of copper foams followed by calcination. The porous and radial configuration of the hierarchical CuO NWs on the Cu foam substrate guarantees the remarkably improved electrochemical performance with durable cycle stability and excellent rate capability compared with CuO NWs on Cu foils. The reversible capacity remains 461.5 mAh/g after 100 repeated cycles at a current density of 100 mA/g, and a capacity of 150.6 mAh/g even at a high rate of 1000 mA/g. By examining the surface morphology of the cycled samples, possible performance fading route is proposed. The 3D CuO NWs network with a porous architecture simutaneously reduces the ion diffusion distances, promotes the electrolyte permeation and electronic conductivity. This novel strategy might open a new window to develop durable CuO based composite anodes for LIBs.
| S-EPMC5916934 | biostudies-literature
Project description:There is an urgent need to improve the energy density of Li-ion batteries to enable mass-market penetration of electric vehicles, grid-scale energy storage, and next-generation consumer electronics. Silicon-graphite composites are currently the most plausible anode material to overcome the capacity limit of graphite or poor cycling performance of silicon. One serious and unrecognized limitation to the use of the composite as an anode is the incompatibility of hydrophobic (natural) graphite with the hydrophilic Si, which adversely affects battery performance. Herein, we report a novel, practical approach to modify the graphite resulting in the formation of a hard carbon coating and graphene sheets that give rise to higher compatibility with Si nanoparticles in the composite. Electrochemical and battery testing of the composite (10 wt % Si) anode shows higher reversible capacity (10% at C/12 and 20% at C/2) than the composite with unmodified graphite reaching ∼600 mAh/g with 95% retention after 100 cycles. The enhanced battery performance is explained by the uniform distribution of Si nanoparticles at the modified graphite surface due to the presence of graphene conductive networks and a thin, oxygen-rich, amorphous carbon layer on the surface of graphite particles, as evidenced by transmission electron microscopy (TEM) images and X-ray photoelectron spectra (XPS). This work provides a new approach to prepare graphite compatible materials that can work with hydrophilic components other than silicon for various applications other than batteries.
| S-EPMC7860062 | biostudies-literature
Project description:Porous structured silicon has been regarded as a promising candidate to overcome pulverization of silicon-based anodes. However, poor mechanical strength of these porous particles has limited their volumetric energy density towards practical applications. Here we design and synthesize hierarchical carbon-nanotube@silicon@carbon microspheres with both high porosity and extraordinary mechanical strength (>200 MPa) and a low apparent particle expansion of ~40% upon full lithiation. The composite electrodes of carbon-nanotube@silicon@carbon-graphite with a practical loading (3 mAh cm-2) deliver ~750 mAh g-1 specific capacity, <20% initial swelling at 100% state-of-charge, and ~92% capacity retention over 500 cycles. Calendered electrodes achieve ~980 mAh cm-3 volumetric capacity density and <50% end-of-life swell after 120 cycles. Full cells with LiNi1/3Mn1/3Co1/3O2 cathodes demonstrate >92% capacity retention over 500 cycles. This work is a leap in silicon anode development and provides insights into the design of electrode materials for other batteries.
| S-EPMC7081208 | biostudies-literature
Project description:Lithium (Li) metal is a promising anode material for lithium-ion batteries (LIBs) because of its high theoretical specific capacity of 3860 mAh g-1 and the low potential of -3.04 V versus the standard hydrogen electrode (SHE). However, these anodes rely on repeated plating and stripping of Li, which leads to consumption of Li inventory and the growth of dendrites that can lead to self-discharge and safety issues. To address these issues, as well as problems related to the volume change of these anodes, a number of different porous conductive scaffolds have been reported to create high surface area electrode on which Li can be plated reliably. While impressive results have been reported in literature, current processes typically rely on either expensive or poorly scalable techniques. Herein, we report a scalable fabrication method to create robust 3D Cu anodes using a one-step electrodeposition process. The areal loading, pore structure, and electrode thickness can be tuned by changing the electrodeposition parameters, and we show how standard mechanical calendering provides a way to further optimize electrode volume, capacity, and cycling stability. Optimized electrodes achieve high Coulombic efficiencies (CEs) of 99% during 800 cycles in half cells at a current density of 0.5 mA cm-2 with a total capacity of 0.5 mAh cm-2. To the best of our knowledge, this is the highest value ever reported for a host for Li-metal anodes using lithium bis(trifluoromethanesulfonyl)imide LITFSI based electrolyte.
| S-EPMC10416568 | biostudies-literature
Project description:We describe the fabrication of filamentous hydrogel nanoparticles using a unique soft lithography based particle molding process referred to as PRINT (particle replication in nonwetting templates). The nanoparticles possess a constant width of 80 nm, and we varied their lengths ranging from 180 to 5000 nm. In addition to varying the aspect ratio of the particles, the deformability of the particles was tuned by varying the cross-link density within the particle matrix. Size characteristics such as hydrodynamic diameter and persistence length of the particles were analyzed using dynamic light scattering and electron microscopy techniques, respectively, while particle deformability was assessed by atomic force microscopy. Additionally, the ability of the particles to pass through membranes containing 0.2 ?m pores was assessed by means of a simple filtration technique, and particle recovery was determined using fluorescence spectroscopy. The results show that particle recovery is mostly independent of aspect ratio at all cross-linker concentrations utilized, with the exception of 96 wt % PEG diacrylate 80 × 5000 nm particles, which showed the lowest percent recovery.
| S-EPMC3374061 | biostudies-literature
Project description:Si is considered as the promising anode materials for lithium-ion batteries (LIBs) owing to their high capacities of 4200 mAh g-1 and natural abundancy. However, severe electrode pulverization and poor electronic and Li-ionic conductivities hinder their practical applications. To resolve the afore-mentioned problems, we first demonstrate a cation-mixed disordered lattice and unique Li storage mechanism of single-phase ternary GaSiP2 compound, where the liquid metallic Ga and highly reactive P are incorporated into Si through a ball milling method. As confirmed by experimental and theoretical analyses, the introduced Ga and P enables to achieve the stronger resistance against volume variation and metallic conductivity, respectively, while the cation-mixed lattice provides the faster Li-ionic diffusion capability than those of the parent GaP and Si phases. The resulting GaSiP2 electrodes delivered the high specific capacity of 1615 mAh g-1 and high initial Coulombic efficiency of 91%, while the graphite-modified GaSiP2 (GaSiP2@C) achieved 83% of capacity retention after 900 cycles and high-rate capacity of 800 at 10,000 mA g-1. Furthermore, the LiNi0.8Co0.1Mn0.1O2//GaSiP2@C full cells achieved the high specific capacity of 1049 mAh g-1 after 100 cycles, paving a way for the rational design of high-performance LIB anode materials.
| S-EPMC10006393 | biostudies-literature