Dataset Information

Facial Tightening Effects, Following Focused and Radial Acoustic Wave Therapy Assessment, Using a Three-Dimensional Digital Imaging.

ABSTRACT:

Background and objectives

Acoustic wave therapy is a novel facial tightening technique that involves nonthermal penetration of the skin and subcutaneous tissue, affecting cells and their metabolism, and resulting in an increased release of unwanted fat and activation of blood and lymphatic flow in tissues. The objective of this study was to investigate the effectiveness of acoustic wave therapy.

Study design/materials and methods

A total of 333 patients underwent multiple facial tightening treatment sessions using focused and radial acoustic waves. Each patient received 2,000-3,000 pulses of focused acoustic waves at a power of 0.45-0.88 mJ/mm² with a pulse frequency of 3-5 Hz and 4,000 pulses of radial acoustic waves at 4-bar power at a frequency of 21 Hz. These sessions were performed more than three times, and treatments were repeated at 1-month intervals. Digital photographs superimposed three-dimensional volumetric assessments, and three-dimensional skin surface displacement calculations using vectors were used to evaluate the results 12 months after the last treatment. Patients also evaluated the results using a 5-point Likert scale.

Results

Improvements in skin texture, clarity, and laxity were observed in digital photographs. Superimposed three-dimensional color images showed marked volumetric reduction and/or formative modification for even contour toward the lower mid-face. Most vectors showed three-dimensional skin surface displacement at the lateral sides of the temples, cheeks, and chin, in an upward direction. These results were obtained and sustained for up to 12 months without edematous reactions. Almost all patients reported improvement, with 79% reporting "good" or "excellent" improvement. Complications were minor and transitory. Persistent side effects were not observed.

Conclusion

Acoustic wave therapy could be used as a standard facial tightening treatment, with skin rejuvenation effects shown on digital photographs and three-dimensional quantification assessments. This noninvasive acoustic wave approach was found to be a safe, long-lasting, and effective method for facial tightening. Lasers Surg. Med. 00:00-00, 2020. © 2020 Wiley Periodicals LLC.

SUBMITTER: Kimura K

PROVIDER: S-EPMC8246538 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:BackgroundPeripheral pulmonary lesion (PPL) incidence is rising because of increased chest imaging sensitivity and frequency. For PPLs suspicious for lung cancer, current clinical guidelines recommend tissue diagnosis. Radial endobronchial ultrasound (R-EBUS) is a bronchoscopic technique used for this purpose. It has been observed that diagnostic yield is impacted by the ability to accurately manipulate the radial probe. However, such skills can be acquired, in part, from simulation training. Three-dimensional (3D) printing has been used to produce training simulators for standard bronchoscopy but has not been specifically used to develop similar tools for R-EBUS.ObjectiveWe report the development of a novel ultrasound-compatible, anatomically accurate 3D-printed R-EBUS simulator and evaluation of its utility as a training tool.MethodsComputed tomography images were used to develop 3D-printed airway models with ultrasound-compatible PPLs of "low" and "high" technical difficulty. Twenty-one participants were allocated to two groups matched for prior R-EBUS experience. The intervention group received 15 minutes to pretrain R-EBUS using a 3D-printed model, whereas the nonintervention group did not. Both groups then performed R-EBUS on 3D-printed models and were evaluated using a specifically developed assessment tool.ResultsFor the "low-difficulty" model, the intervention group achieved a higher score (21.5 ± 2.02) than the nonintervention group (17.1 ± 5.7), reflecting 26% improvement in performance (P = 0.03). For the "high-difficulty" model, the intervention group scored 20.2 ± 4.21 versus 13.3 ± 7.36, corresponding to 52% improvement in performance (P = 0.02). Participants derived benefit from pretraining with the 3D-printed model, regardless of prior experience level.Conclusion3D-printing can be used to develop simulators for R-EBUS education. Training using these models significantly improves procedural performance and is effective in both novice and experienced trainees.