Browse
Submit Data
Databases
API
Help

Dataset Information

55 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

High-throughput design of high-performance lightweight high-entropy alloys.

ABSTRACT: Developing affordable and light high-temperature materials alternative to Ni-base superalloys has significantly increased the efforts in designing advanced ferritic superalloys. However, currently developed ferritic superalloys still exhibit low high-temperature strengths, which limits their usage. Here we use a CALPHAD-based high-throughput computational method to design light, strong, and low-cost high-entropy alloys for elevated-temperature applications. Through the high-throughput screening, precipitation-strengthened lightweight high-entropy alloys are discovered from thousands of initial compositions, which exhibit enhanced strengths compared to other counterparts at room and elevated temperatures. The experimental and theoretical understanding of both successful and failed cases in their strengthening mechanisms and order-disorder transitions further improves the accuracy of the thermodynamic database of the discovered alloy system. This study shows that integrating high-throughput screening, multiscale modeling, and experimental validation proves to be efficient and useful in accelerating the discovery of advanced precipitation-strengthened structural materials tuned by the high-entropy alloy concept.

SUBMITTER: Feng R

PROVIDER: S-EPMC8282813 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

First principles-based design of lightweight high entropy alloys.

Project description:Recently, the design of lightweight high entropy alloys (HEAs) with a mass density lower than 5 g/cm3 has attracted much research interest in structural materials. We applied a first principles-based high-throughput method to design lightweight HEAs in single solid-solution phase. Three lightweight quinary HEA families were studied: AlBeMgTiLi, AlBeMgTiSi and AlBeMgTiCu. By comprehensively exploring their entire compositional spaces, we identified the most promising compositions according to the following design criteria: the highest stability, lowest mass density, largest elastic modulus and specific stiffness, along with highest Pugh's ratio. We found that HEAs with the topmost compositions exhibit a negative formation energy, a low density and high specific Young's modulus, but a low Pugh's ratio. Importantly, we show that the most stable composition, Al0.31Be0.15Mg0.14Ti0.05Si0.35 is energetically more stable than its metallic compounds and it significantly outperforms the current lightweight engineering alloys such as the 7075 Al alloy. These results suggest that the designed lightweight HEAs can be energetically more stable, lighter, and stiffer but slightly less ductile compared to existing Al alloys. Similar conclusions can be also drawn for the AlBeMgTiLi and AlBeMgTiCu. Our design methodology and findings serve as a valuable tool and guidance for the experimental development of lightweight HEAs.

| S-EPMC10728166 | biostudies-literature

Al-Ti-Containing Lightweight High-Entropy Alloys for Intermediate Temperature Applications.

Project description:In this study, new high-entropy alloys (HEAs), which contain lightweight elements, namely Al and Ti, have been designed for intermediate temperature applications. Cr, Mo, and V were selected as the elements for the Al-Ti-containing HEAs by elemental screening using their binary phase diagrams. AlCrMoTi and AlCrMoTiV HEAs are confirmed as solid solutions with minor ordered B2 phases and have superb specific hardness when compared to that of commercial alloys. The present work demonstrates the desirable possibility for substitution of traditional materials that are applied at intermediate temperature to Al-Ti-containing lightweight HEAs.

| S-EPMC7512874 | biostudies-literature

A first-principles-based high fidelity, high throughput approach for the design of high entropy alloys.

Project description:Here, we present a preselected small set of ordered structures (PSSOS) method, a first principles-based high fidelity (HF), high throughput (HT) approach, for fast screening of the large composition space of high entropy alloys (HEAs) to select the most energetically stable, single-phase HEAs. Taking quinary AlCoCrFeNi HEA as an example system, we performed PSSOS calculations on the formation energies and mass densities of 8801 compositions in both FCC and BCC lattices and selected five most stable FCC and BCC HEAs for detailed analysis. The calculation results from the PSSOS approach were compared with existing experimental and first-principles data, and the good agreement was achieved. We also compared the PSSOS with the special quasi-random structures (SQS) method, and found that with a comparable accuracy, the PSSOS significantly outperforms the SQS in efficiency, making it ideal for HF, HT calculations of HEAs.

| S-EPMC9279411 | biostudies-literature

Design of high bulk moduli high entropy alloys using machine learning.

Project description:In this work, the authors have demonstrated the use of machine learning (ML) models in the prediction of bulk modulus for High Entropy Alloys (HEA). For the first time, ML has been used for optimizing the composition of HEA to achieve enhanced bulk modulus values. A total of 12 ML algorithms were trained to classify the elemental composition as HEA or non-HEA. Among these models, Gradient Boosting Classifier (GBC) was found to be the most accurate, with a test accuracy of 78%. Further, six regression models were trained to predict the bulk modulus of HEAs, and the best results were obtained by LASSO Regression model with an R-square value of 0.98 and an adjusted R-Square value of 0.97 for the test data set. This work effectively bridges the gap in the discovery and property analysis of HEAs. By accelerating material discovery via providing alternate means for designing virtual alloy compositions having favourable bulk modulus for respective applications, this work opens new avenues of applications of HEAs.

| S-EPMC10665368 | biostudies-literature

Design metastability in high-entropy alloys by tailoring unstable fault energies.

Project description:Metastable alloys with transformation-/twinning-induced plasticity (TRIP/TWIP) can overcome the strength-ductility trade-off in structural materials. Originated from the development of traditional alloys, the intrinsic stacking fault energy (ISFE) has been applied to tailor TRIP/TWIP in high-entropy alloys (HEAs) but with limited quantitative success. Here, we demonstrate a strategy for designing metastable HEAs and validate its effectiveness by discovering seven alloys with experimentally observed metastability for TRIP/TWIP. We propose unstable fault energies as the more effective design metric and attribute the deformation mechanism of metastable face-centered cubic alloys to unstable martensite fault energy (UMFE)/unstable twin fault energy (UTFE) rather than ISFE. Among the studied HEAs and steels, the traditional ISFE criterion fails in more than half of the cases, while the UMFE/UTFE criterion accurately predicts the deformation mechanisms in all cases. The UMFE/UTFE criterion provides an effective paradigm for developing metastable alloys with TRIP/TWIP for an enhanced strength-ductility synergy.

| S-EPMC9462695 | biostudies-literature

Snoek-type damping performance in strong and ductile high-entropy alloys.

Project description:Noise and mechanical vibrations not only cause damage to devices, but also present major public health hazards. High-damping alloys that eliminate noise and mechanical vibrations are therefore required. Yet, low operating temperatures and insufficient strength/ductility ratios in currently available high-damping alloys limit their applicability. Using the concept of high-entropy alloy (HEA), we present a class of high-damping materials. The design is based on refractory HEAs, solid-solutions doped with either 2.0 atomic % oxygen or nitrogen, (Ta0.5Nb0.5HfZrTi)98O2 and (Ta0.5Nb0.5HfZrTi)98N2. Via Snoek relaxation and ordered interstitial complexes mediated strain hardening, the damping capacity of these HEAs is as high as 0.030, and the damping peak reaches up to 800 K. The model HEAs also exhibit a high tensile yield strength of ~1400 MPa combined with a large ductility of ~20%. The high-temperature damping properties, together with superb mechanical properties make these HEAs attractive for applications where noise and vibrations must be reduced.

| S-EPMC7299626 | biostudies-literature

Ab initio-predicted micro-mechanical performance of refractory high-entropy alloys.

Project description:Recently developed high-entropy alloys (HEAs) consisting of multiple principal elements represent a new field of metallurgy and have demonstrated appealing properties for a wide range of applications. Using ab initio alloy theory, we reveal the alloying effect on the elastic properties and the ideal tensile strength (ITS) in the [001] direction of four body-centered cubic (bcc) refractory HEAs based on Zr, V, Ti, Nb, and Hf. We find that these HEAs show high elastic anisotropy and large positive Cauchy pressure, suggesting good extrinsic ductility. Starting from ZrNbHf, it is found that the ITS decreases with equimolar Ti addition. On the other hand, if both Ti and V are added to ZrNbHf, the ITS is enhanced by about 42%. An even more captivating effect is the ITS increase by about 170%, if Ti and V are substituted for Hf. The alloying effect on the ITS is explained by the d-band filling. An intrinsic brittle-to-ductile transition is found in terms of the failure mode under uniaxial tension. These investigations suggest that intrinsically ductile HEAs with high ideal strength can be achieved by controlling the proportion of group four elements to group five elements.

| S-EPMC4510575 | biostudies-other

Fatigue dataset of high-entropy alloys.

Project description:Fatigue failure of metallic structures is of great concern to industrial applications. A material will not be practically useful if it is prone to fatigue failures. To take the advantage of lately emerged high-entropy alloys (HEAs) for designing novel fatigue-resistant alloys, we compiled a fatigue database of HEAs from the literature reported until the beginning of 2022. The database is subdivided into three categories, i.e., low-cycle fatigue (LCF), high-cycle fatigue (HCF), and fatigue crack growth rate (FCGR), which contain 15, 23, and 28 distinct data records, respectively. Each data record in any of three categories is characteristic of a summary, which is comprised of alloy compositions, key fatigue properties, and additional information influential to, or interrelated with, fatigue (e.g., material processing history, phase constitution, grain size, uniaxial tensile properties, and fatigue testing conditions), and an individual dataset, which makes up the original fatigue testing curve. Some representative individual datasets in each category are graphically visualized. The dataset is hosted in an open data repository, Materials Cloud.

| S-EPMC9259632 | biostudies-literature

Twinning in metastable high-entropy alloys.

Project description:Twinning is a fundamental mechanism behind the simultaneous increase of strength and ductility in medium- and high-entropy alloys, but its operation is not yet well understood, which limits their exploitation. Since many high-entropy alloys showing outstanding mechanical properties are actually thermodynamically unstable at ambient and cryogenic conditions, the observed twinning challenges the existing phenomenological and theoretical plasticity models. Here, we adopt a transparent approach based on effective energy barriers in combination with first-principle calculations to shed light on the origin of twinning in high-entropy alloys. We demonstrate that twinning can be the primary deformation mode in metastable face-centered cubic alloys with a fraction that surpasses the previously established upper limit. The present advance in plasticity of metals opens opportunities for tailoring the mechanical response in engineering materials by optimizing metastable twinning in high-entropy alloys.

| S-EPMC6006257 | biostudies-literature

Bulk-independent surface oxide composition controls the electrochemical performance of high-entropy alloys.

Project description:Multi-element alloys and high-entropy alloys show promising electrocatalytic behavior for water splitting and other catalytic reactions, due to their highly tunable composition. While preparation and synthesis of these materials are thoroughly investigated, the true reactive surface composition is still not well understood, as it may significantly differ from the bulk composition. Precise knowledge and understanding of resulting surface composition is crucial for effective control of the electrocatalytic performance. In this work, low energy ion scattering spectroscopy was applied to determine the surface oxide composition of a series of Ni-based multi-metallic alloys with Mn, Fe, Co, and Cr under alkaline, neutral and acidic conditions. The composition of the surface oxide was investigated with sub-nanometer depth resolution. In electrochemical tests, good catalytic activity was found for the oxygen evolution reaction, although a strong dependence on the selected reaction conditions was observed. The surface composition under OER conditions deviates significantly from the bulk composition. No significant benefit of high entropy alloying compared with binary or ternary alloys concerning catalytic OER performance was found.

| S-EPMC11348829 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data