Dataset Information

Biomechanical Determinants of Performance and Injury Risk During Cutting: A Performance-Injury Conflict?

ABSTRACT:

Background

Most cutting biomechanical studies investigate performance and knee joint load determinants independently. This is surprising because cutting is an important action linked to performance and non-contact anterior cruciate ligament (ACL) injuries. The aim of this study was to investigate the relationship between cutting biomechanics and cutting performance (completion time, ground contact time [GCT], exit velocity) and surrogates of non-contact ACL injury risk (knee abduction [KAM] and internal rotation [KIRM] moments) during 90° cutting.

Design

Mixed, cross-sectional study following an associative design. 61 males from multidirectional sports performed six 90° pre-planned cutting trials, whereby lower-limb and trunk kinetics and kinematics were evaluated using three-dimensional (3D) motion and ground reaction force analysis over the penultimate (PFC) and final foot contact (FFC). Pearson's and Spearman's correlations were used to explore the relationships between biomechanical variables and cutting performance and injury risk variables. Stepwise regression analysis was also performed.

Results

Faster cutting performance was associated (p ≤ 0.05) with greater centre of mass (COM) velocities at key instances of the cut (r or ρ = 0.533-0.752), greater peak and mean propulsive forces (r or ρ = 0.449-0.651), shorter FFC GCTs (r or ρ = 0.569-0.581), greater FFC and PFC braking forces (r = 0.430-0.551), smaller hip and knee flexion range of motion (r or ρ = 0.406-0.670), greater knee flexion moments (KFMs) (r = 0.482), and greater internal foot progression angles (r = - 0.411). Stepwise multiple regression analysis revealed that exit velocity, peak resultant propulsive force, PFC mean horizontal braking force, and initial foot progression angle together could explain 64% (r = 0.801, adjusted 61.6%, p = 0.048) of the variation in completion time. Greater peak KAMs were associated with greater COM velocities at key instances of the cut (r or ρ = - 0.491 to - 0.551), greater peak knee abduction angles (KAA) (r = - 0.468), and greater FFC braking forces (r = 0.434-0.497). Incidentally, faster completion times were associated with greater peak KAMs (r = - 0.412) and KIRMs (r = 0.539). Stepwise multiple regression analysis revealed that FFC mean vertical braking force and peak KAA together could explain 43% (r = 0.652, adjusted 40.6%, p < 0.001) of the variation peak KAM.

Conclusion

Techniques and mechanics associated with faster cutting (i.e. faster COM velocities, greater FFC braking forces in short GCTs, greater KFMs, smaller hip and knee flexion, and greater internal foot progression angles) are in direct conflict with safer cutting mechanics (i.e. reduced knee joint loading, thus ACL injury risk), and support the "performance-injury conflict" concept during cutting. Practitioners should be conscious of this conflict when instructing cutting techniques to optimise performance while minimising knee joint loading, and should, therefore, ensure that their athletes have the physical capacity (i.e. neuromuscular control, co-contraction, and rapid force production) to tolerate and support the knee joint loading during cutting.

SUBMITTER: Dos'Santos T

PROVIDER: S-EPMC8363537 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:Directional changes in cutting maneuvers are critical in sports, where shoe torsional stiffness (STS) is an important factor. Shoes are designed based on different constructions and movement patterns. Hence, it is unclear how adjustable spacers into the sole constructions of air pressure chambers (APC) affect the STS in side-step cutting. Therefore, this study investigated the effects of altered STS through adjustable sole spacers on ground reaction force (GRF) and ankle and knee joint moments in side-step cutting. Seventeen healthy recreational athletes performed side-step cutting with experimental conditions including (i) barefoot (BF), (ii) unaltered shoes (UAS): soles consisting of APC, and (iii) altered shoes (AS): modified UAS by inserting elastomeric spacers into cavities formed by APC. Mechanical and biomechanical variables were measured. Significant differences were revealed across shoe conditions for impact peak (p = 0.009) and impulse (p = 0.018) in vertical GRF, time to achieve peak braking (p = 0.004), and peak propulsion (p = 0.025) for anterior-posterior GRF in ANOVA test. No significant differences were observed in GRF peaks and impulses between UAS and AS except for a trend of differences in impact peak (p = 0.087) for vertical GRF. At the ankle and knee joint, peak ankle power absorption (p = 0.019), peak knee internal rotation moment (p = 0.042), peak knee extension moment (p = 0.001), peak knee flexion moment (0.000), peak knee power absorption (p = 0.047) showed significant difference across three shoe conditions. However, no significant differences between the UAS and AS were noticed for peak joint moments and power. Altered shoe torsional stiffness did not significantly affect the peak forces and peak ankle and knee joint moments or powers; hence sole adjustment did not influence the cutting performance. This study might be insightful in sports footwear design, and adjusting shoe torsional stiffness by sole modification might be advantageous for athletes playing sports with cutting maneuvers to reduce the risk of injuries by controlling the twisting force at the ankle that frequently happens during cutting maneuvers.