Valorization and Mechanical Recycling of Heterogeneous Post-Consumer Polymer Waste through a Mechano-Chemical Process.
Ontology highlight
ABSTRACT:
SUBMITTER: Capuano R
PROVIDER: S-EPMC8399838 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:In this work, we explored a microwave-assisted glycolysis process to chemically recycle rigid polyurethane (PU) foam waste to obtain a single-phase product with suitable physio-chemical properties as a secondary raw material for the preparation of new rigid PU products. Such an approach was compared to a conventionally heated (ConvH) process, analyzing the performances of different catalysts. The use of microwaves allowed a 94% decrease in the reaction time scale of rigid PU depolymerization, with a concurrent 45% reduction in energy expense. By using a PU/diethylene glycol mass ratio of 1.5, best performances were obtained with a 30 mmol/100gPU potassium acetate concentration, both in terms of the product viscosity and aromatic amine byproduct content. The glycolysis products recovered were employed in substitution to virgin polyol for rigid PU foam preparation, showing improved compressive strength and comparable thermal insulation properties up to a 30% content with respect to the traditional non-recycled counterpart.
| S-EPMC9909786 | biostudies-literature
Project description:Inspirational concepts, and the transfer of analogs from natural biology to science and engineering, has produced many excellent technologies to date, spanning vaccines to modern architectural feats. This review highlights that answers to the pressing global petroleum-based plastic waste challenges, can be found within the mechanics and mechanisms natural ecosystems. Here, a suite of technological and engineering approaches, which can be implemented to operate in tandem with nature's prescription for regenerative material circularity, is presented as a route to plastics sustainability. A number of mechanical/green chemical (pre)treatment methodologies, which simulate natural weathering and arthropodal dismantling activities are reviewed, including: mechanical milling, reactive extrusion, ultrasonic-, UV- and degradation using supercritical CO2. Akin to natural mechanical degradation, the purpose of the pretreatments is to render the plastic materials more amenable to microbial and biocatalytic activities, to yield effective depolymerization and (re)valorization. While biotechnological based degradation and depolymerization of both recalcitrant and bioplastics are at a relatively early stage of development, the potential for acceleration and expedition of valuable output monomers and oligomers yields is considerable. To date a limited number of independent mechano-green chemical approaches and a considerable and growing number of standalone enzymatic and microbial degradation studies have been reported. A convergent strategy, one which forges mechano-green chemical treatments together with the enzymatic and microbial actions, is largely lacking at this time. An overview of the reported microbial and enzymatic degradations of petroleum-based synthetic polymer plastics, specifically: low-density polyethylene (LDPE), high-density polyethylene (HDPE), polystyrene (PS), polyethylene terephthalate (PET), polyurethanes (PU) and polycaprolactone (PCL) and selected prevalent bio-based or bio-polymers [polylactic acid (PLA), polyhydroxyalkanoates (PHAs) and polybutylene succinate (PBS)], is detailed. The harvesting of depolymerization products to produce new materials and higher-value products is also a key endeavor in effectively completing the circle for plastics. Our challenge is now to effectively combine and conjugate the requisite cross disciplinary approaches and progress the essential science and engineering technologies to categorically complete the life-cycle for plastics.
| S-EPMC8260098 | biostudies-literature
Project description:Increasing the stream of recycled plastic necessitates an approach beyond the traditional recycling via melting and re-extrusion. Various chemical recycling processes have great potential to enhance recycling rates. In this Review, a summary of the various chemical recycling routes and assessment via life-cycle analysis is complemented by an extensive list of processes developed by companies active in chemical recycling. We show that each of the currently available processes is applicable for specific plastic waste streams. Thus, only a combination of different technologies can address the plastic waste problem. Research should focus on more realistic, more contaminated and mixed waste streams, while collection and sorting infrastructure will need to be improved, that is, by stricter regulation. This Review aims to inspire both science and innovation for the production of higher value and quality products from plastic recycling suitable for reuse or valorization to create the necessary economic and environmental push for a circular economy.
| S-EPMC7497176 | biostudies-literature
Project description:In the following work, the hydrothermal degradation of polypropylene waste (PP) using supercritical water (SCW) has been studied. The procedure was carried out in a high-pressure, high-temperature batch reactor at 425 °C and 450 °C from 15 to 240 min. The results show a high yield of the oil (up to 95%) and gas (up to 20%) phases. The gained oil phase was composed of alkanes, alkenes, cycloalkanes, aromatic hydrocarbons, and alcohols. Alkanes and alcohols predominated at 425 °C and shorter reaction times, while the content of aromatic hydrocarbons sharply increased at higher temperatures and times. The higher heating values (HHVs) of oil phases were in the range of liquid fuel (diesel, gasoline, crude and fuel oil), and they were between 48 and 42 MJ/kg. The gas phase contained light hydrocarbons (C1-C6), where propane was the most represented component. The results for PP degradation obtained in the present work were compared to the results of SCW degradation of colored PE waste, and the potential degradation mechanism of polyolefins waste in SCW is proposed. The results allowed to conclude that SCW processing technology represents a promising and eco-friendly tool for the liquefaction of polyolefin (PE and PP) waste into oil with a high conversion rate.
| S-EPMC9609547 | biostudies-literature
Project description:It becomes common to wear a disposable face mask to protect from coronavirus disease 19 (COVID-19) amid this pandemic. However, massive generations of contaminated face mask cause environmental concerns because current disposal processes (i.e., incineration and reclamation) for them release toxic chemicals. The disposable mask is made of different compounds, making it hard to be recycled. In this regard, this work suggests an environmentally benign disposal process, simultaneously achieving the production of valuable fuels from the face mask. To this end, CO2-assisted thermo-chemical process was conducted. The first part of this work determined the major chemical constituents of a disposable mask: polypropylene, polyethylene, nylon, and Fe. In the second part, pyrolysis study was employed to produce syngas and C1-2 hydrocarbons (HCs) from the disposable mask. To enhance syngas and C1-2 HCs formations, multi-stage pyrolysis was used for more C-C and C-H bonds scissions of the disposable mask. Catalytic pyrolysis over Ni/SiO2 further expedited H2 and CH4 formations due to its capability for dehydrogenation. In the presence of CO2, catalytic pyrolysis additionally produced CO, while pyrolysis in N2 did not produce it. Therefore, the thermo-chemical conversion of disposable face mask and CO2 could be an environmentally benign way to remove COVID-19 plastic waste, generating value-added products.
| S-EPMC7426216 | biostudies-literature
Project description:Solvent-based recycling is a promising approach for closed-loop recovery of plastic-containing waste. It avoids the energy cost to depolymerize the plastic but still allows to clean the polymer of contaminants and additives. However, viscosity plays an important role in handling the polymer solutions at high concentrations and in the cleaning steps. This Review addresses the viscosity behavior of polymer solutions, available data, and (mostly algebraic) models developed. The non-Newtonian viscosity models, such as the Carreau and Yasuda-Cohen-Armstrong models, pragmatically describe the viscosity of polymer solutions at different concentrations and shear rate ranges. This Review also describes how viscosity influences filtration and centrifugation processes, which are crucial steps in the cleaning of the polymer and includes a polystyrene/styrene case study.
| S-EPMC8519067 | biostudies-literature
Project description:ZnII -complexes bearing half-salan ligands were exploited in the mild and selective chemical upcycling of various commercial polyesters and polycarbonates. Remarkably, we report the first example of discrete metal-mediated poly(bisphenol A carbonate) (BPA-PC) methanolysis being appreciably active at room temperature. Indeed, Zn(2)2 and Zn(2)Et achieved complete BPA-PC consumption within 12-18 mins in 2-Me-THF, noting high bisphenol A (BPA) yields (SBPA =85-91 %) within 2-4 h. Further kinetic analysis found such catalysts to possess kapp values of 0.28±0.040 and 0.47±0.049 min-1 respectively at 4 wt%, the highest reported to date. A completely circular upcycling approach to plastic waste was demonstrated through the production of several renewable poly(ester-amide)s (PEAs), based on a terephthalamide monomer derived from bottle-grade poly(ethylene terephthalate) (PET), which exhibited excellent thermal properties.
| S-EPMC9306953 | biostudies-literature
Project description:Increasing plastic waste recycling is a milestone of European environmental policy to reduce environmental impacts and dependency on foreign resources. This is particularly challenging for plastic packaging waste, consisting of very heterogeneous fractions and typically rather contaminated. In this study, we collected primary data from plants sorting and recycling plastic packaging waste to illustrate process efficiencies, material flows, and barriers. We observed that significant losses of target materials occurred both at sorting and recycling stages. These were higher for polymers such as films, polypropylene and polystyrene, and lower for polyethylene terephthalate and high-density polyethylene. Applying material flow analysis, we estimated an overall end-of-life recycling rate for post-consumer plastic packaging waste in EU27 in 2017 of 14% (not considering waste exported as recycled; 25% otherwise). An improved scenario for 2030 showed that achieving an overall end-of-life recycling rate of about 49% was possible when best available practices and technologies were implemented. To fulfil the ambitious recycling targets set at EU27 level (55% overall recycling rate), substantial improvements are necessary at the plants, product design, collection system, and market level. Our findings further indicate that films and other problematic contaminants in the input-waste considerably hamper the recovery rates, thus the improvement of the efficiency of the collection systems is imperative. In parallel, the development of markets for lower value fractions, e.g. polypropylene, could be a way forward to increase recycling, while improvements in the product design will considerably reduce the presence of impurities and contaminants in the input-waste.
| S-EPMC8162419 | biostudies-literature
Project description:This study aimed to establish a new methodology for upgrading biomass quality using low-temperature (below 100 °C) oxidation to achieve simultaneous drying and decomposition. Sterilized manure (63% wet basis) was heated at 90 °C for 49 days under an oxidative environment. The obtained solid and moisture reduction curves indicated that drying and decomposition proceeded simultaneously. The biomass was decomposed by oxidation with the release of water, carbon dioxide, and volatile fatty acids such as acetic acid. The oxidation process stopped when the biomass was dehydrated, indicating that the water originally present in the biomass governed the process. Elemental and calorific analyses revealed no remarkable increase in carbon content or increased heating value, and a slight decrease in oxygen content. Although the severity of the process was insufficient to produce an optimum solid fuel due to the low temperature used, the process would enable the stabilization of waste biomass with low energy consumption such as using waste heat.
| S-EPMC5912774 | biostudies-literature
Project description:Phytophthora infestans, causal agent of late blight in potato and tomato, remains challenging to control. Unravelling its biomechanics of host invasion, and its response to mechanical and chemical stress, could provide new handles to combat this devastating pathogen. Here we introduce two fluorescent molecular sensors, CWP-BDP and NR12S, that reveal the micromechanical response of the cell wall-plasma membrane continuum in P. infestans during invasive growth and upon chemical treatment. When visualized by live-cell imaging, CWP-BDP reports changes in cell wall (CW) porosity while NR12S reports variations in chemical polarity and lipid order in the plasma membrane (PM). During invasive growth, mechanical interactions between the pathogen and a surface reveal clear and localized changes in the structure of the CW. Moreover, the molecular sensors can reveal the effect of chemical treatment to CW and/or PM, thereby revealing the site-of-action of crop protection agents. This mechano-chemical imaging strategy resolves, non-invasively and with high spatio-temporal resolution, how the CW-PM continuum adapts and responds to abiotic stress, and provides information on the dynamics and location of cellular stress responses for which, to date, no other methods are available.
| S-EPMC8760408 | biostudies-literature