Browse
Submit Data
Databases
API
Help

Dataset Information

27 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Effect of Precursor Nature and Sol-Gel Synthesis Conditions on TiO₂ Aerogel's Structure.

ABSTRACT: The aim of this investigation was to synthesize high porosity TiO₂ aerogel by applying sol-gel and subcritical drying methods and to identify the influence of reagent's nature and synthesis conditions on their structural and optical properties. Methods of XRD, FT-IR, BET, STA, SEM, and UV-vis were applied to investigate and compare the properties of synthesized TiO₂ aerogels and to determine the most effective synthesis route. The structural parameters of the synthesized materials can be varied by changing the precursor type (titanium (IV), isopropoxide (TIP), or tetrabutylorthotitanate (TBOT)) and the nature of the solvent used for additional exchange (n-hexane (nH), cyclohexane (CH), or diethyl ether (DE)). All of the subcritical dried samples show the amorphous structure, which tends to crystallize into the anatase phase after calcination. The number of micro and mesopores and the specific surface area depends on the synthesis conditions. The pores with the highest diameter have been found for additionally nH exchanged and aged aerogel synthesized from precursor TIP. Despite the imperfections in the structure, the produced aerogels show structural and optical properties typical of the TiO₂ structures mentioned in the literature.

SUBMITTER: Doneliene J

PROVIDER: S-EPMC8401230 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Foldable and Cytocompatible Sol-gel TiO2 Photonics.

Project description:Integrated photonics provides a miniaturized and potentially implantable platform to manipulate and enhance the interactions between light and biological molecules or tissues in in-vitro and in-vivo settings, and is thus being increasingly adopted in a wide cross-section of biomedical applications ranging from disease diagnosis to optogenetic neuromodulation. However, the mechanical rigidity of substrates traditionally used for photonic integration is fundamentally incompatible with soft biological tissues. Cytotoxicity of materials and chemicals used in photonic device processing imposes another constraint towards these biophotonic applications. Here we present thin film TiO2 as a viable material for biocompatible and flexible integrated photonics. Amorphous TiO2 films were deposited using a low temperature (<250 °C) sol-gel process fully compatible with monolithic integration on plastic substrates. High-index-contrast flexible optical waveguides and resonators were fabricated using the sol-gel TiO2 material, and resonator quality factors up to 20,000 were measured. Following a multi-neutral-axis mechanical design, these devices exhibit remarkable mechanical flexibility, and can sustain repeated folding without compromising their optical performance. Finally, we validated the low cytotoxicity of the sol-gel TiO2 devices through in-vitro cell culture tests. These results demonstrate the potential of sol-gel TiO2 as a promising material platform for novel biophotonic devices.

| S-EPMC4561379 | biostudies-literature

Effect of reaction solvent on hydroxyapatite synthesis in sol-gel process.

Project description:Synthesis of hydroxyapatite (HA) through sol-gel process in different solvent systems is reported. Calcium nitrate tetrahydrate (CNTH) and diammonium hydrogen phosphate (DAHP) were used as calcium and phosphorus precursors, respectively. Three different synthesis reactions were carried out by changing the solvent media, while keeping all other process parameters constant. A measure of 0.5?M aqueous DAHP solution was used in all reactions while CNTH was dissolved in distilled water, tetrahydrofuran (THF) and N,N-dimethylformamide (DMF) at a concentration of 0.5?M. Ammonia solution (28-30%) was used to maintain the pH of the reaction mixtures in the 10-12 range. All reactions were carried out at 40?±?2°C for 4?h. Upon completion of the reactions, products were filtered, washed and calcined at 500°C for 2?h. It was clearly demonstrated through various techniques that the dielectric constant and polarity of the solvent mixture strongly influence the chemical structure and morphological properties of calcium phosphate synthesized. Water-based reaction medium, with highest dielectric constant, mainly produced ?-calcium pyrophosphate (?-CPF) with a minor amount of HA. DMF/water system yielded HA as the major phase with a very minor amount of ?-CPF. THF/water solvent system with the lowest dielectric constant resulted in the formation of pure HA.

| S-EPMC5750015 | biostudies-literature

Tailoring Mesoporous Titania Features by Ultrasound-Assisted Sol-Gel Technique: Effect of Surfactant/Titania Precursor Weight Ratio.

Project description:A mesoporous titania structure has been prepared using the ultrasound-assisted sol-gel technique in order to find out a way to tailor its structure. The TiO2 obtained was compared to the same version of titania but synthesized by a conventional sol-gel method with the objective of understanding the effect of ultrasound in the synthesis process. All synthesis experiments were focused on the preparation of a titania photocatalyst. Thus, the anatase photocatalytic active phase of titania was proven by X-ray diffraction. Additionally, the ultrasonation treatment proved to increase the crystallinity of titania samples, being one of the requirements to having good photocatalytic activity for titania. The influence of surfactant/titania precursor weight ratio on the structural (XRD), textural (N2-sorption measurements), morphological (TEM), surface chemistry (FTIR) and optical properties (UVDR) was investigated. It was observed that the crystallite size, specific surface area, band gap energy and even photocatalytic activity was affected by the synergism occurring between cavitation effect and the surfactant/titania precursor weight ratio. The study yielded interesting great results that could be considered for further application of ultrasound to tailor mesoporous titania features via sol-gel soft template synthesis, against conventional sol-gel process.

| S-EPMC8150942 | biostudies-literature

Sol-Gel-Synthesis of Nanoscopic Complex Metal Fluorides.

Project description:The fluorolytic sol-gel synthesis for binary metal fluorides (AlF?, CaF?, MgF?) has been extended to ternary and quaternary alkaline earth metal fluorides (CaAlF?, Ca?AlF?, LiMgAlF?). The formation and crystallization of nanoscopic ternary CaAlF? and Ca?AlF? sols in ethanol were studied by 19F liquid and solid state NMR (nuclear magnetic resonance) spectroscopy, as well as transmission electron microscopy (TEM). The crystalline phases of the annealed CaAlF?, Ca?AlF?, and LiMgAlF? xerogels between 500 and 700 °C could be determined by X-ray powder diffraction (XRD) and 19F solid state NMR spectroscopy. The thermal behavior of un-annealed nanoscopic ternary and quaternary metal fluoride xerogels was ascertained by thermal analysis (TG/DTA). The obtained crystalline phases of CaAlF? and Ca?AlF? derived from non-aqueous sol-gel process were compared to crystalline phases from the literature. The corresponding nanoscopic complex metal fluoride could provide a new approach in ceramic and luminescence applications.

| S-EPMC5707579 | biostudies-literature

Sol-Gel Processed TiO2 Nanotube Photoelectrodes for Dye-Sensitized Solar Cells with Enhanced Photovoltaic Performance.

Project description:The performance of dye-sensitized solar cells (DSCs) critically depends on the efficiency of electron transport within the TiO2-dye-electrolyte interface. To improve the efficiency of the electron transfer the conventional structure of the working electrode (WE) based on TiO2 nanoparticles (NPs) was replaced with TiO2 nanotubes (NTs). Sol-gel method was used to prepare undoped and Nb-doped TiO2 NPs and TiO2 NTs. The crystallinity and morphology of the WEs were characterized using XRD, SEM and TEM techniques. XPS and PL measurements revealed a higher concentration of oxygen-related defects at the surface of NPs-based electrodes compared to that based on NTs. Replacement of the conventional NPs-based TiO2 WE with alternative led to a 15% increase in power conversion efficiency (PCE) of the DSCs. The effect is attributed to the more efficient transfer of charge carriers in the NTs-based electrodes due to lower defect concentration. The suggestion was confirmed experimentally by electrical impedance spectroscopy measurements when we observed the higher recombination resistance at the TiO2 NTs-electrolyte interface compared to that at the TiO2 NPs-electrolyte interface. Moreover, Nb-doping of the TiO2 structures yields an additional 14% PCE increase. The application of Nb-doped TiO2 NTs as photo-electrode enables the fabrication of a DSC with an efficiency of 8.1%, which is 35% higher than that of a cell using a TiO2 NPs. Finally, NTs-based DSCs have demonstrated a 65% increase in the PCE value, when light intensity was decreased from 1000 to 10 W/m2 making such kind device be promising alternative indoor PV applications when the intensity of incident light is low.

| S-EPMC7075133 | biostudies-literature

Sol-gel Autocombustion Synthesis of Nanocrystalline High-entropy Alloys.

Project description:A reduction in the particle size is expected to improve the properties and increase the application potential of high-entropy alloys. Therefore, in this study, a novel sol-gel autocombustion technique was first used to synthesize high-entropy alloys. The average grain size of the prepared nanocrystalline CoCrCuNiAl high-entropy alloys showed was 14 nm with an excellent and uniform dispersion, exhibiting a distinct magnetic behavior similar to the superparamagnetic behavior. We show that the metal nitrates first form (Co,Cu,Mg,Ni,Zn)O high-entropy oxides, and then in situ reduce to CoCrCuNiAl high-entropy alloys by the reducing gases, and the chelation between citric acid and the metal ions and the in situ chemical reactions are the dominant reaction mechanisms. We demonstrate that the sol-gel autocombustion process is an efficient way to synthesize solid solution alloys eluding the restriction of a high mixing entropy.

| S-EPMC5469749 | biostudies-literature

Influence of the Nature of Aminoalcohol on ZnO Films Formed by Sol-Gel Methods.

Project description:Here we present comparative studies of: (i) the formation of ZnO thin films via the sol-gel method using zinc acetate dihydrate (ZAD), 2-methoxyethanol (ME) as solvent, and the aminoalcohols (AA): ethanolamine, (S)-(+)-2-amino-1-propanol, (S)-(+)-2-amino-3-methyl-1-butanol, 2-aminophenol, and aminobenzyl alcohol, and (ii) elemental analyses, infrared spectroscopy, X-ray diffraction, scanning electron microscopy, absorption and emission spectra of films obtained after deposition by drop coating on glass surface, and thermal treatments at 300, 400, 500 and 600 °C. The results obtained provide conclusive evidences of the influence of the AA used (aliphatic vs. aromatic) on the ink stability (prior to deposition), and on the composition, structures, morphologies, and properties of films after calcination, in particular, those due to the different substituents, H, Me, or iPr, and to the presence or the absence of a -CH2 unit. Aliphatic films, more stable and purer than aromatic ones, contained the ZnO wurtzite form for all annealing temperatures, while the cubic sphalerite (zinc-blende) form was also detected after using aromatic AAs. Films having frayed fibers or quartered layers or uniform yarns evolved to "neuron-like" patterns. UV and photoluminescence studies revealed that these AAs also affect the optical band gap, the structural defects, and photo-optical properties of the films.

| S-EPMC10052816 | biostudies-literature

Evolution of the Local Structure in the Sol-Gel Synthesis of Fe<sub>3</sub>C Nanostructures.

Project description:The sol-gel synthesis of iron carbide (Fe3C) nanoparticles proceeds through multiple intermediate crystalline phases, including iron oxide (FeOx) and iron nitride (Fe3N). The control of particle size is challenging, and most methods produce polydisperse Fe3C nanoparticles of 20-100 nm in diameter. Given the wide range of applications of Fe3C nanoparticles, it is essential that we understand the evolution of the system during the synthesis. Here, we report an in situ synchrotron total scattering study of the formation of Fe3C from gelatin and iron nitrate sol-gel precursors. A pair distribution function analysis reveals a dramatic increase in local ordering between 300 and 350 °C, indicating rapid nucleation and growth of iron oxide nanoparticles. The oxide intermediate remains stable until the emergence of Fe3N at 600 °C. Structural refinement of the high-temperature data revealed local distortion of the NFe6 octahedra, resulting in a change in the twist angle suggestive of a carbonitride intermediate. This work demonstrates the importance of intermediate phases in controlling the particle size of a sol-gel product. It is also, to the best of our knowledge, the first example of in situ total scattering analysis of a sol-gel system.

| S-EPMC8277138 | biostudies-literature

Floating photocatalyst of B-N-TiO2/expanded perlite: a sol-gel synthesis with optimized mesoporous and high photocatalytic activity.

Project description:Optimized mesoporous photocatalyst endowed with high specific surface area and large pore size was synthesized by sol-gel method. These large pore mesoporous materials (33.39?nm) were conducive to the movement of larger molecules or groups in pore path and for effective use of active sites. The high specific surface area (SBET, 99.23?m(2)?g(-1)) was beneficial to catalytic oxidation on the surface. Moreover, B and N co-doped anatase TiO2 in the presence of Ti-O-B-N and O-Ti-B-N contributed to the pore structure optimization and enhanced photoresponse capacity with a narrow band gap and red shift of absorption. The obtained materials with floating characteristics based on expanded perlite (EP) showed favorable features for photocatalytic activity. The best RhB photodegration rate of B-N-TiO2/EP (6?mg/g, 24?wt% TiO2) reached 99.1% after 5?h in the visible region and 99.8% after 1?h in the UV region. The findings can provide insights to obtain floatable photocatalysts with simple preparation method, optimized mesoporous, co-doping agents, as well as good photocatalytic performance, coverable and reusability. B-N-TiO2/EP has potential applications for practical environmental purification.

| S-EPMC4949471 | biostudies-other

Irradiation-catalysed degradation of methyl orange using BaF2-TiO2 nanocomposite catalysts prepared by a sol-gel method.

Project description:BaF2-TiO2 nanocomposite material (hereinafter called the composite) was prepared by a sol-gel method. The composite surface area, morphology and structure were characterized by Brunauer-Emmett-Teller method, X-ray diffraction analysis and a scanning electron microscopy. The results showed that BaF2 and TiO2 form a PN-like structure on the surface of the composite. Composites were used to catalyse the degradation of methyl orange by irradiation with ultraviolet light, γ-rays and an electron beam (EB). It was demonstrated that the composite is found to be more efficient than the prepared TiO2 and commercial P25 in the degradation of methyl orange under γ-irradiation. Increasing the composite catalyst concentration within a certain range can effectively improve the decolorization rate of the methyl orange solution. However, when the composite material is used to catalyse the degradation of organic matter in the presence of ultraviolet light or 10 MeV EB irradiation, the catalytic effect is poor or substantially ineffective. In addition, a hybrid mechanism is proposed; BaF2 absorbs γ-rays to generate radioluminescence and further excites TiO2 to generate photo-charges. Due to the heterojunction effect, the resulting photo-charge will produce more active particles. This seems to be a possible mechanism to explain γ-irradiation's catalytic behaviour.

| S-EPMC6837232 | biostudies-literature