Dataset Information

Mitigation of Aerosols Generated During Exercise Testing With a Portable High-Efficiency Particulate Air Filter With Fume Hood.

ABSTRACT:

Background

The role of portable high-efficiency particulate air (HEPA) filters for supplemental aerosol mitigation during exercise testing is unknown and might be relevant during COVID-19 pandemic.

Research question

What is the effect of portable HEPA filtering on aerosol concentration during exercise testing and its efficiency in reducing room clearance time in a clinical exercise testing laboratory?

Study design and methods

Subjects were six healthy volunteers aged 20 to 56 years. In the first experiment, exercise was performed in a small tent with controlled airflow with the use of a stationary cycle, portable HEPA filter with fume hood, and particle counter to document aerosol concentration. Subjects performed a four-stage maximal exercise test that lasted 12 min plus 5 min of pretest quiet breathing and 3 min of active recovery. First, they exercised without mitigation then with portable HEPA filter running. In a separate experiment, room aerosol clearance time was measured in a clinical exercise testing laboratory by filling it with artificially generated aerosols and measuring time to 99.9% aerosol clearance with heating, ventilation, and air conditioning (HVAC) only or HVAC plus portable HEPA filter running.

Results

In the exercise experiment, particle concentrations reached 1,722 ± 1,484/L vs 96 ± 124/L (P < .04) for all particles (>0.3 μm), 1,339 ± 1,281/L vs 76 ± 104/L (P < .05) for smaller particles (0.3 to 1.0 μm), and 333 ± 209/L vs 17 ± 19/L (P < .01) for larger particles (1.0 to 5.0 μm) at the end of the protocol in a comparison of mitigation vs portable HEPA filter. Use of a portable HEPA filter in a clinical exercise laboratory clearance experiment reduced aerosol clearance time 47% vs HVAC alone.

Interpretation

The portable HEPA filter reduced the concentration of aerosols generated during exercise testing by 96% ± 2% for all particle sizes and reduced aerosol room clearance time in clinical exercise testing laboratories. Portable HEPA filters therefore might be useful in clinical exercise testing laboratories to reduce the risk of COVID-19 transmission.

SUBMITTER: Garzona-Navas A

PROVIDER: S-EPMC8463654 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:ObjectivesThe novel coronavirus disease 2019 (COVID-19) epidemic that emerged in December 2019 has rapidly evolved in recent months to become a worldwide and ongoing pandemic. Shortage of medical masks remains an unresolved problem. This study aims to investigate the filtration efficiency (FE) of home-made masks that could be used as alternatives for community mitigation of COVID-19.Study designExperimental observational analytic study.MethodsThe FE of home-made masks and medical masks (as the control) were tested under laminar flow within a scaled air duct system using nebulised NaCl aerosols sized 6-220 nm. The size-resolved NaCl aerosol count was measured using a scanning mobility particle-sizer spectrometer. Home-made masks with an external plastic face shield also underwent a splash test. In addition, the fibre structures of medical masks were studied under an electron microscope after treatment with either 75% alcohol or soap and water at 60 °C.ResultsThe FE of the home-made masks at 6-200 nm were non-inferior to that of medical masks (84.54% vs 86.94%, P = 0.102). Both types of masks achieved an FE of 90% at 6-89 nm. A significantly higher FE was achieved when one piece of tissue paper was added adjacent to the inner surface of the medical mask than medical mask alone (6-200 nm: 91.64% vs 86.94%, P < 0.0001; 6-89 nm: 94.27% vs 90.54%, P < 0.0001; 90-200 nm: 82.69% vs 73.81%, P < 0.0001). The plastic face shield prevented the home-made mask from fluid splash. The fibre structures of the external surface of medical masks were damaged after treatment with either 75% alcohol or soap and water at 60 °C.ConclusionsThe home-made masks in this study, which were made of one piece of tissue paper and two pieces of kitchen towels, layered from face to external, had an FE at 6-200 nm non-inferior to that of medical mask materials, which had a certified FE of ≥95% at 3 μm. In the current COVID-19 pandemic with the shortage of medical masks, these home-made masks combined with an external plastic shield could be used as an alternative to medical masks for community mitigation. In addition, one piece of tissue paper could be placed adjacent to the inner surface of a medical mask to prolong effective lifespan of the medical mask. These demand reduction strategies could be used to reserve medical masks for use in healthcare and certain high-risk community settings, such as symptomatic persons, caregivers and attendees to healthcare institutions.