Dataset Information

Effective Removal of Cr(VI) from Wastewater Using Biochar Derived from Walnut Shell.

ABSTRACT: Heavy metals are the major concern of the modern age. Among the heavy metals, chromium (Cr(VI)) is regarded as a highly toxic heavy metal released largely from leather tanning operations. To remove such high concentrations of Cr(VI), an advanced method is required urgently. Thus, biosorption using biochar, which is an organic material produced from various sources such as walnut shell, can be applied successfully for Cr(VI) abatement. The major objectives of this experiment were the remediation of the Cr(VI) heavy metal using walnut shell biochar and checking of the effect of pH, biochar dosage, Cr level, and shaking time. Remediation of Cr(VI) using walnut shell biochar was proved to be effective and removed the maximum concentration of Cr(VI) up to 93% at pH 5.5, 2 h agitation time, and the biochar amount of 1.1 g L^-1 from an aqueous solution. Equilibrium modeling demonstrated that the chemisorption process was involved in adsorption of Cr(VI). The surface of the biochar was porous and provided numerous sites for Cr(VI) attachment, which was also confirmed by the presence of Cr(VI) onto the biochar after adsorption. Hence, the use of walnut shell biochar was highly effective as a sorbent, which could conveniently be applied to small-scale as well as large-scale levels.

SUBMITTER: Kokab T

PROVIDER: S-EPMC8467037 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:Heavy metal ions in water refer to significant risks to the biological system due to their high toxicity. Therefore, the decontamination of water polluted by heavy metal ions attracts significant interest of researchers. Adsorption by nanomaterials has been a widely used technique for removing heavy metal ions from water. Chitosan was extracted from shrimp shellfish and mixed with laboratory-prepared AgNPs/GO in the ratio of 3 : 1. A series of tests evaluates the best condition of pH, amount of adsorbent, retention time, stirring speed, temp, and initial concentration. The research was conducted under various conditions. Langmuir, Freundlich, Tempkin, and Dubinin-Radushkevich isotherms were also tested. Also, the column adsorption experiment was carried out on industrial wastewater at different flow rates and column bed heights. The optimal values of the contact time, pH, and adsorbent dose of Cr(vi) were found to be 80 min, 4, and 0.1 g 100 mL-1, respectively, at room temperature (30 °C), agitation at 150 rpm, and initial concentration of 50 ppm. On the other hand, the optimal value of contact time, pH, and adsorbent dose of Fe(iii) were found to be 30 min, 6, and 0.02 g 100 mL-1, respectively, at room temp (30 °C) with a stirring speed of 250 rpm and an initial concentration of 40 ppm. For Cr(vi) and Fe(iii), equilibrium studies show that the data fit the Freundlich isotherm well (correlation coefficient, R 2 = 0.98) (III). A link between the pseudo-second order active model and data fitting the pseudo-first order active models were made. Within the intraparticle diffusion model, there are four stages that the mechanism must go through before it is at equilibrium. The adsorbent was tested in an industrial adsorbent column. This test proves that the nanocomposite's adsorption capacity can be restored by washing it with 0.1 M HCl, as shown by the periodicity test. After four cycles, the amount of Cr(vi) adsorbed on AgNPs/GO/chitosan was just 20%, which is insufficient for further adsorption experiments. Cr(vi) removal rates (%R) decreased slightly.

Dataset Information

Effective Removal of Cr(VI) from Wastewater Using Biochar Derived from Walnut Shell.

Similar Datasets

OmicsDI is part of the ELIXIR infrastructure

Tweets