Browse
Submit Data
Databases
API
Help

Dataset Information

8 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Superior Gas Barrier Properties of Biodegradable PBST vs. PBAT Copolyesters: A Comparative Study.

ABSTRACT: As a bio-based counterpart of poly(butylene adipate-co-terephthalate) (PBAT), the well-known commercially available biodegradable aliphatic-aromatic copolyester, poly(butylene succinate-co-terephthalate) (PBST) has comparable physical and mechanical properties, but its gas barrier properties, which are very important for packaging material and mulch film applications, have not yet been reported in literature. In this paper, the O₂, CO₂ and water vapor barrier properties of PBST vs. PBAT were comparatively studied and reported for the first time. Theoretical calculation of O₂ and CO₂ permeation coefficients via group contribution method was also conducted. The barrier properties of PBST show clear copolymer composition dependence due to different contribution of BS and BT repeat units and composition-dependent crystallinity. Comparing with PBAT, PBST with close copolymer and three-phase (crystalline, amorphous, rigid amorphous) compositions shows 3.5 times O₂ and CO₂ and 1.5 times water vapor barrier properties. The slower segment movement and less free volume of PBST, and therefore slower gas diffusion in PBST, accounts for its superior O₂ and CO₂ barrier, while the better hydrophilicity of PBST counteracts partial contribution of slower segment movement so that the improvement in water vapor barrier is not as high as in O₂ and CO₂ barrier.

SUBMITTER: Qin P

PROVIDER: S-EPMC8512549 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

In Situ Formation of Microfibrillar PBAT in PGA Films: An Effective Way to Robust Barrier and Mechanical Properties for Fully Biodegradable Packaging Films

Project description:Poly(glycolic acid)

| S-EPMC9348010 | biostudies-literature

Properties of Biodegradable Films Based on Poly(butylene Succinate) (PBS) and Poly(butylene Adipate-co-Terephthalate) (PBAT) Blends †,‡.

Project description:Compression molded biodegradable films based on poly(butylene succinate) (PBS) and poly(butylene adipate-co-terephthalate) (PBAT) at varying weights were prepared, and their relevant properties for packaging applications are here reported. The melt rheology of the blends was first studied, and the binary PBS/PBAT blends exhibited marked shear thinning and complex thermoreological behavior, due to the formation of a co-continuous morphology in the 50 wt% blend. The films were characterized by infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), mechanical tensile tests, scanning electron microscopy (SEM), and oxygen and water vapor permeability. PBS crystallization was inhibited in the blends with higher contents of PBAT, and FTIR and SEM analysis suggested that limited interactions occur between the two polymer phases. The films showed increasing stiffness as the PBS percentage increased; further, a sharp decrease in elongation at break was noticed for the films containing percentages of PBS greater than 25 wt%. Gas permeability decreased with increasing PBS content, indicating that the barrier properties of PBS can be tuned by blending with PBAT. The results obtained point out that the blend containing 25 wt% PBS is a good compromise between elastic modulus (135 MPa) and deformation at break (390%) values. Overall, PBS/PBAT blends represent an alternative for packaging films, as they combine biodegradability, good barrier properties and reasonable mechanical behavior.

| S-EPMC7600530 | biostudies-literature

Layering?Triggered Delayering with Exfoliated High?Aspect Ratio Layered Silicate for Enhanced Gas Barrier, Mechanical Properties, and Degradability of Biodegradable Polymers

Project description:Abstract Research on biodegradable polymers with the intention of fast, complete degradation in industrial compost (i?compost) for organic recyclability is paramount to identifying solutions to the problem of excessive plastic waste originating specifically from packaging. Conventional biodegradable polymers, such as polylactide (PLA), are far from optimum for this application due to the poor gas barrier properties and slow degradation. In the paper, a new concept (triggered degradation by delayering) is shown in which exfoliated, self?assembled sodium?hectorite (Hec) arranged in a layer?by?layer manner alternating with electrospun hot?pressed PLA provides strong gas barrier properties at high humidity and simultaneously accelerates the degradation of PLA, as tested in an enzymatic solution and i?compost. A thin composite film (thickness 56 µm) shows a tensile strength and modulus 58 and 2000 MPa, respectively, whereas oxygen permeability is as low as 0.0064 cm3 cm m?2 day?1 bar?1. Furthermore, the delayering of the composite film by swelling of Hec layer led to accelerated degradation of PLA, as shown in detail by enzymatic and compost degradation. Since such concepts for enhanced degradability are urgently needed for sustainable utilization of biodegradable polymers in plastic waste management, the present work is an important step ahead. Enhanced degradability, modulus, and decreased oxygen permeability required for packaging is achieved in polylactide (PLA) by making its composites with exfoliated sodium hectorite (Hec) in a layer?by?layer structure. The layered structure enables improved mechanical and gas permeation properties, while the delayering of composite films due to the swelling of Hec provide accelerates degradation.

| S-EPMC7507042 | biostudies-literature

Morphological and Rheological Properties of PLA, PBAT, and PLA/PBAT Blend Nanocomposites Containing CNCs.

Project description:Morphological and rheological properties of poly(lactic acid), PLA (semicrystalline and amorphous), and poly(butylene adipate-co-terephthalate), PBAT, and their blends (75 wt%/25 wt%; PLA/PBAT) were investigated in the presence of cellulose nanocrystals (CNCs) prepared from solution casting followed by melt mixing. For the solution casting step, the CNCs were either incorporated into the matrix, the dispersed phase, or both. The dispersion and distribution of the CNCs in the neat polymers and localization in their blends were analyzed via scanning electron microscopy (SEM) and atomic force microscopy (AFM). The highly dispersed CNCs in the solution cast nanocomposites were agglomerated after melt mixing. In the blends with 1 wt% CNCs, the nanoparticles were mostly localized on the surface of the PBAT droplets irrespective of their initial localization. The rheological behavior of the single polymer matrix nanocomposites and their blends was determined in dynamic and transient shear flow in the molten state. Upon melt mixing the complex viscosity and storage modulus of the solution cast nanocomposites decreased markedly due to re-agglomeration of the CNCs. Under shearing at 0.1 s-1, a significant droplet coalescence was observed in the neat blends, but was prevented by the presence of the CNCs at the interface in the blend nanocomposites.

| S-EPMC8065413 | biostudies-literature

High-Barrier Polyimide Containing Carbazole Moiety: Synthesis, Gas Barrier Properties, and Molecular Simulations.

Project description:A high-barrier polyimide (2,7-CPI) was synthesized through the polymerization of pyromellitic dianhydride (PMDA) and a novel diamine (2,7-CDA) containing carbazole moiety. The synthesized diamine and polyimide were fully characterized by elemental analyses, FTIR and NMR. The 2,7-CPI displays very attractive barrier performances, with oxygen transmission rate (OTR) and water vapor transmission rate (WVTR) low to 0.14 cm3·m-2·day-1 and 0.05 g·m-2·day-1, respectively. Meanwhile, 2,7-CPI also exhibits exceptional thermal stability with a glass transition temperature (Tg) of 467 °C, 5% weight-loss temperature (Td5%) of 550 °C under N2 and coefficient of thermal expansion (CTE) of 3.4 ppm/K. The barrier performances of 2,7-CPI are compared with those of a structural analogue (2,7-CPPI) and a typical polyimide (Kapton). Their barrier performances with respect to microstructure were investigated by molecular simulations, wide angle X-ray diffraction (WAXD), and positron annihilation lifetime spectroscopy (PALS). The results show that 2,7-CPI possesses better coplanar structure and more number of intermolecular hydrogen bonds among the three PIs, which result in tight chain packing and thereby high crystallinity, low free volume, and decreased chains mobility. That is, the high crystallinity and low free volume of 2,7-CPI reduce the diffusion and solubility of gases. Meanwhile, the poor chains mobility further decreases the gases diffusion. The reduced diffusion and solubility of gases consequently promote the improvement of barrier properties for 2,7-CPI. The polyimide has a wide application prospect in the field of flexible electronic packaging industries.

| S-EPMC7565694 | biostudies-literature

Uncompatibilized PBAT/PLA Blends: Manufacturability, Miscibility and Properties.

Project description:Polymer blends of poly(butylene adipate-co-terephthalate) (PBAT) and polylactide (PLA) have been drawn attention due to the application potential as packaging or agricultural films. This study aims to determine the manufacturability, miscibility and mechanical properties of uncompatibilized PBAT/PLA blends prepared using different techniques. First, PBAT and PLA are melt-blended in a wide range of ratios from 90/10 to 10/90. The compounds are then processed into pressed panels, flat films and blown films. Finally, the thermal, morphological, rheological and mechanical properties of these blends are investigated. PBAT/PLA blends have a small difference of solubility parameters, predicting theoretically good miscibility. However, they show two almost unchanged glass transition temperatures in the DSC, phase separation in SEM and two relaxation mechanisms in the Cole-Cole plot. The phase morphology varies depending on both the blend ratios and the preparation techniques. Tensile tests indicate that with increasing PLA content the elongation at break decreases. A good correlation between the elongation at break and the tear propagation resistance is found. Furthermore, the trouser tear method is proven to be more applicable to differentiate highly extensible blown films compared with the Elmendorf tear method.

| S-EPMC7662590 | biostudies-literature

Methylation of guar gum for improving mechanical and barrier properties of biodegradable packaging films.

Project description:Improving functional properties of biopolymers for use as environment friendly packaging is an area of current interest. Biodegradable films with improved barrier and mechanical properties were prepared from methylated guar gum. Methylation resulted in structural modification of guar gum (GG) promoting greater crystallization thereby enhancing thermal stability towards decomposition. Reduction in radius of gyration (Rg), weight average molecular weight (Mw), and an increase in polydispersity index (PDI) were also observed due to methylation. Methylated guar gum (MGG) films exhibited 40% lower water vapor transmission rate (WVTR) as compared to control purified guar gum (PGG) films. Films prepared by partial replacement of PGG with MGG (10, 25, 50, 75 and 100% w/w) showed gradual improvement in percent elongation. The study gives an insight on the role of methylation in enhancing barrier and mechanical properties of GG based biodegradable films for possible application in food packaging.

| S-EPMC6787019 | biostudies-literature

Interactions, Structure and Properties of PLA/lignin/PBAT Hybrid Blends.

Project description:Poly(butylene adipate-co-terephthalate) (PBAT) was added to poly(lactic acid) (PLA)/lignin blends to decrease the considerable stiffness and brittleness of the blends. Two- and three-component blends were prepared in a wide composition range through homogenization in an internal mixer followed by compression molding. Interactions among the components were estimated by comparing the solubility parameters of the materials used and through thermal analysis. Mechanical properties were characterized by tensile testing. The structure of the blends was studied using scanning electron (SEM) and digital optical (DOM) microscopy. The results showed that the interactions between PBAT and lignin are somewhat stronger than those between PLA and the other two components. The maleic anhydride grafted PLA added as a coupling agent proved completely ineffective; it does not modify the interactions. The structural analysis confirmed the immiscibility of the components; the structure of the blends was heterogeneous at each composition. A dispersed structure formed when the concentration of one of the components was small, while, depending on lignin content, an interpenetrating network-like structure developed and phase inversion took place in the range of 30-60 vol% PBAT content. Lignin was located mainly in the PBAT phase. Properties were determined by the relative amount of PBAT and PLA; the addition of lignin deteriorated properties, mainly the deformability of the blends. Other means, such as reactive processing, must be used to improve compatibility and blend properties. The results contribute considerably to a better understanding of structure-property correlations in lignin-based hybrid blends.

| S-EPMC10422597 | biostudies-literature

Comparative physiology of the pulmonary blood-gas barrier: the unique avian solution.

Project description:Two opposing selective pressures have shaped the evolution of the structure of the blood-gas barrier in air breathing vertebrates. The first pressure, which has been recognized for 100 years, is to facilitate diffusive gas exchange. This requires the barrier to be extremely thin and have a large area. The second pressure, which has only recently been appreciated, is to maintain the mechanical integrity of the barrier in the face of its extreme thinness. The most important tensile stress comes from the pressure within the pulmonary capillaries, which results in a hoop stress. The strength of the barrier can be attributed to the type IV collagen in the extracellular matrix. In addition, the stress is minimized in mammals and birds by complete separation of the pulmonary and systemic circulations. Remarkably, the avian barrier is about 2.5 times thinner than that in mammals and also is much more uniform in thickness. These advantages for gas exchange come about because the avian pulmonary capillaries are unique among air breathers in being mechanically supported externally in addition to the strength that comes from the structure of their walls. This external support comes from epithelial plates that are part of the air capillaries, and the support is available because the terminal air spaces in the avian lung are extremely small due to the flow-through nature of ventilation in contrast to the reciprocating pattern in mammals.

| S-EPMC2803621 | biostudies-literature

Improvement of Barrier Properties of Biodegradable Polybutylene Succinate/Graphene Nanoplatelets Nanocomposites Prepared by Melt Process.

Project description:Polybutylene Succinate (PBS)/Graphene nanoplatelets (GnP) nanocomposites over a range of GnP from 0 to 1.35 wt.%. were prepared by a melt process. A mixture of individual graphene nanosheets and aggregates was obtained by the addition of GnP in the PBS matrix. The presence of these fillers did not significantly modify the morphology, crystalline microstructure of the matrix or its thermal stability. However, a slight reinforcement effect of PBS was reported in the presence of GnP. The water sorption isotherm modelling with Guggenheim, Andersen and De Boer (GAB) equation and Zimm-Lundberg theory allowed a phenomenological analysis at the molecular scale. The presence of GnP did not modify the water sorption capacity of the PBS matrix. From a kinetic point of view, a decrease of the diffusion coefficient with the increasing GnP content was obtained and was attributed to a tortuosity effect. The influence of water activity was discussed over a range of 0.5 to 1 and 0 to 0.9 for water and dioxygen permeability. Improvement of the barrier properties by 38% and 35% for water and dioxygen permeability respectively were obtained.

| S-EPMC7926900 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data