Multi-objective optimization of the cavitation generation unit structure of an advanced rotational hydrodynamic cavitation reactor
Ontology highlight
ABSTRACT:
SUBMITTER: Sun X
PROVIDER: S-EPMC8551246 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Hydrodynamic cavitation is a promising technique for water disinfection. In the present paper, the disinfection characteristics of an advanced hydrodynamic cavitation reactor (ARHCR) in pilot scale were studied. The effects of various flow rates (1.4-2.6 m3/h) and rotational speeds (2600-4200 rpm) on the removal of Escherichia coli (E. coli) were revealed and analyzed. The variation regularities of the log reduction and reaction rate constant at various cavitation numbers were established. A disinfection rate of 100% was achieved in only 4 min for 15 L of simulated effluent under 4200 rpm and 1.4 m3/h, with energy efficiency at 0.0499 kWh/L. A comprehensive comparison with previously introduced HCRs demonstrates the superior performance of the presented ARHCR system. The morphological changes in E. coli were studied by scanning electron microscopy. The results indicate that the ARHCR can lead to serious cleavage and surface damages to E. coli, which cannot be obtained by conventional HCRs. Finally, a possible damage mechanism of the ARHCR, including both the hydrodynamical and sonochemical effects, was proposed. The findings of the present study can provide strong support to the fundamental understanding and applications of ARHCRs for water disinfection.
| S-EPMC8059091 | biostudies-literature
Project description:Hydrodynamic cavitation (HC) has emerged as one of the most potential technologies for industrial-scale water treatment. The advanced rotational hydrodynamic cavitation reactors (ARHCRs) that appeared recently have shown their high effectiveness and economical efficiency compared with conventional devices. For the interaction-type ARHCRs where cavitation is generated from the interaction between the cavitation generation units (CGUs) located on the rotor and the stator, their flow field, cavitation generation mechanism, and interaction process are still not well defined. The present study experimentally and numerically investigated the cavitation flow characteristics in a representative interaction-type ARHCR which has been proposed in the past. The cavitation generation mechanism and development process, which was categorized into "coinciding", "leaving", and "approaching" stages, were analyzed explicitly with experimental flow visualization and computational fluid dynamics (CFD) simulations. The changes in the cavitation pattern, area ratio, and sheet cavitation length showed high periodicity with a period of 0.5 ms/cycle at a rotational speed of 3,600 rpm in the flow visualization. The experimental and CFD results indicated that sheet cavitation can be generated on the downstream sides of both the moving and the static CGUs. The sheet cavitation was induced and continuously enlarged in the "leaving" and "approaching" stages and was crushed after the moving CGUs coincided with the static CGUs. In addition, vortex cavitation was formed in the vortex center of each CGU due to high-speed rotating fluid motion. The shape and size of the vortex cavitation were determined by the compression effect produced by the interaction. The findings of this work are important for the fundamental understanding, design, and application of the ARHCRs in water treatment.
| S-EPMC7786598 | biostudies-literature
Project description:Hydrodynamic cavitation reactors are of great promise for the applications of chemical process intensification and water treatment. In this work, a novel cylindrical rotational hydrodynamic cavitation reactor (CRHCR) with rectangular grooves and oblique tooth protrusions on the rotor surface was studied. The three-dimensional characterization of cavitation within the CRHCR was observed from the front and left views by the high-speed camera experiments. Interestingly, a new phenomenon of simultaneous formation of the attached cavitation and shear cavitation was found in the CRHCR. The synergistic effect of attached cavitation and shear cavitation contributes to the enhancement of the cavitation performance of CRHCR. In addition, the evolution of attached cavitation is explored. It is found that attached cavitation forms a trapezoidal-shaped cavitation cloud in the groove, which undergoes three various stages: incipient, development, and collapse. Finally, the pulsation frequency and cavitation intensity of shear cavitation in the chamber were investigated. The results show that the cavitation pulsation frequency is the same at the same rotational speed in the chamber near diverse oblique teeth. As the rotational speed increases, the cavitation pulsation frequency increases linearly. These findings in this paper are of great benefit to understanding the mechanism of the cavitation effect of CRHCR.
| S-EPMC11295464 | biostudies-literature
Project description:Hydrodynamic cavitation (HC) has been extensively investigated for effluent treatment applications. Performance of HC devices or processes is often reported in terms of degradation of organic pollutants rather than quantification of hydroxyl (OH) radicals. In this study, generation of OH radicals in vortex based cavitation device using coumarin dosimetry was quantified. Coumarin was used as the chemical probe with an initial concentration of 100 µM (15 ppm). Generation of OH radicals was quantified by analysing generated single hydroxylated products. The influence of operating parameters such as pH and type of acid used to adjust pH, dissolved oxygen, and inlet and outlet pressures was investigated. Acidic pH was found to be more conducive for generating OH radicals and therefore subsequent experiments were performed at pH of 3. Sulphuric acid was found to be more than three times effective than hydrochloric acid in generating OH radicals. Effect of initial levels of dissolved oxygen was found to influence OH radical generation. Performance of vortex based cavitation device was then compared with other commonly used cavitation devices based on orifice and venturi. The vortex based cavitation device was found to outperform the orifice and venturi based devices in terms of initial per-pass factor. Influence of device scale (nominal flow rate through the device) on performance was then evaluated. The results presented for these devices unambiguously quantifies their cavitational performance. The presented results will be useful for evaluating computational models and stimulate further development of predictive computational models in this challenging area.
| S-EPMC9641053 | biostudies-literature
Project description:A new software tool making use of a genetic algorithm for multi-objective experimental optimization (GAME.opt) was developed based on a strength Pareto evolutionary algorithm. The software deals with high dimensional variable spaces and unknown interactions of design variables. This approach was evaluated by means of multi-objective test problems replacing the experimental results. A default parameter setting is proposed enabling users without expert knowledge to minimize the experimental effort (small population sizes and few generations).
| S-EPMC1705497 | biostudies-other
Project description:BackgroundRenewable liquid biofuel production will reduce crude oil import of India. To displace the huge quantity of fossil fuels used for energy production, this research was focused on utilization of unexploited low-cost agricultural residues for biofuel production. Corncobs are a byproduct of corn processing industry, and till now it is not utilized for biofuel production, eventhough it has high lignocellulosic concent. In this study, combined hydrodynamic cavitation and enzymatic (HCE) method was evaluated as a pretreatment method of corncob for biofuel production. The most significant process parameters namely (i) enzyme loading (3-10 U g-1), (ii) biomass loading (2.5-5.0%), and (iii) duration (5-60 min) were optimized and their effects on combined HCE pretreatment of corncob was studied through response surface methodology for lignin reduction, hemicellulose reduction and cellulose increase.ResultsThe highest lignin reduction (47.4%) was obtained in orifice plate 1 (OP1) under the optimized conditions namely biomass loading at 5%, enzyme loading at 6.5 U g-1 of biomass, and reaction duration of 60 min. The above tested independent variables had a significant effect on lignin reduction. The cavitational yield and energy consumption under the above-mentioned optimized conditions for OP1 was 3.56 × 10-5 g J-1 and 1.35 MJ kg-1, respectively.ConclusionsIt is evident from the study that HCE is an effective technology and requires less energy (1.35 MJ kg-1) than other biomass pretreatment methods.
| S-EPMC6057035 | biostudies-literature
Project description:Many real-world engineering problems need to balance different objectives and can be formatted as multi-objective optimization problem. An effective multi-objective algorithm can achieve a set of optimal solutions that can make a tradeoff between different objectives, which is valuable to further explore and design. In this paper, an improved multi-objective differential evolution algorithm (MOEA/D/DEM) based on a decomposition strategy is proposed to improve the performance of differential evolution algorithm for practical multi-objective nutrition decision problems. Firstly, considering the neighborhood characteristic, a neighbor intimacy factor is designed in the search process for enhancing the diversity of the population, then a new Gaussian mutation strategy with variable step size is proposed to reduce the probability of escaping local optimum area and improve the local search ability. Finally, the proposed algorithm is tested by classic test problems (DTLZ1-7 and WFG1-9) and applied to the multi-objective nutrition decision problems, compared to the other reported multi-objective algorithms, the proposed algorithm has a better search capability and obtained competitive results.
| S-EPMC9729643 | biostudies-literature
Project description:Cavitation, the nucleation of vapour in liquids, is ubiquitous in fluid dynamics, and is often implicated in a myriad of industrial and biomedical applications. Although extensively studied in isotropic liquids, corresponding investigations in anisotropic liquids are largely lacking. Here, by combining liquid crystal microfluidic experiments, nonequilibrium molecular dynamics simulations and theoretical arguments, we report flow-induced cavitation in an anisotropic fluid. The cavitation domain nucleates due to sudden pressure drop upon flow past a cylindrical obstacle within a microchannel. For an anisotropic fluid, the inception and growth of the cavitation domain ensued in the Stokes regime, while no cavitation was observed in isotropic liquids flowing under similar hydrodynamic parameters. Using simulations we identify a critical value of the Reynolds number for cavitation inception that scales inversely with the order parameter of the fluid. Strikingly, the critical Reynolds number for anisotropic fluids can be 50% lower than that of isotropic fluids.
| S-EPMC5459993 | biostudies-literature
Project description:In scientific disciplines, benchmarks play a vital role in driving progress forward. For a benchmark to be effective, it must closely resemble real-world tasks. If the level of difficulty or relevance is inadequate, it can impede progress in the field. Moreover, benchmarks should have low computational overhead to ensure accessibility and repeatability. The objective is to achieve a kind of ``Turing test'' by creating a surrogate model that is practically indistinguishable from the ground truth observation, at least within the dataset's explored boundaries. This objective necessitates a large quantity of data. This data encompasses numerous features that are characteristic of chemistry and materials science optimization tasks that are relevant to industry. These features include high levels of noise, multiple fidelities, multiple objectives, linear constraints, non-linear correlations, and failure regions. We performed 494498 random hard-sphere packing simulations representing 206 CPU days' worth of computational overhead. Simulations required nine input parameters with linear constraints and two discrete fidelities each with continuous fidelity parameters. The data was logged in a free-tier shared MongoDB Atlas database, producing two core tabular datasets: a failure probability dataset and a regression dataset. The failure probability dataset maps unique input parameter sets to the estimated probabilities that the simulation will fail. The regression dataset maps input parameter sets (including repeats) to particle packing fractions and computational runtimes for each of the two steps. These two datasets were used to create a surrogate model as close as possible to running the actual simulations by incorporating simulation failure and heteroskedastic noise. In the regression dataset, percentile ranks were calculated for each group of identical parameter sets to account for heteroskedastic noise, thereby ensuring reliable and accurate data. This differs from the conventional approach that imposes a-priori assumptions, such as Gaussian noise, by specifying mean and standard deviation. This technique can be extended to other benchmark datasets to bridge the gap between optimization benchmarks with low computational overhead and the complex optimization scenarios encountered in the real world.
| S-EPMC10465850 | biostudies-literature
Project description:Guiding experiments to find materials with targeted properties is a crucial aspect of materials discovery and design, and typically multiple properties, which often compete, are involved. In the case of two properties, new compounds are sought that will provide improvement to existing data points lying on the Pareto front (PF) in as few experiments or calculations as possible. Here we address this problem by using the concept and methods of optimal learning to determine their suitability and performance on three materials data sets; an experimental data set of over 100 shape memory alloys, a data set of 223 M2AX phases obtained from density functional theory calculations, and a computational data set of 704 piezoelectric compounds. We show that the Maximin and Centroid design strategies, based on value of information criteria, are more efficient in determining points on the PF from the data than random selection, pure exploitation of the surrogate model prediction or pure exploration by maximum uncertainty from the learning model. Although the datasets varied in size and source, the Maximin algorithm showed superior performance across all the data sets, particularly when the accuracy of the machine learning model fits were not high, emphasizing that the design appears to be quite forgiving of relatively poor surrogate models.
| S-EPMC5829239 | biostudies-literature