Spectroscopy and Theoretical Modeling of Phonon Vibration Modes and Band Gap Energy of Cu2ZnSn(SxSe1–x)4 Bulk Crystals and Thin Films
Ontology highlight
ABSTRACT:
SUBMITTER: Babichuk I
PROVIDER: S-EPMC8567408 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Cu2ZnSn(S, Se)4-based solar cells with total area (0.5 cm2) power conversion efficiency of 6.4% are demonstrated from thin film absorbers processed by inkjet printing technology of Cu-Zn-Sn-S precursor ink followed by selenization. The device performance is limited by the low fill factor, which is due to the high series resistance.
| S-EPMC5115396 | biostudies-literature
Project description:We present studies focused on the evolution of the electronic band structure of the Mo1-x W x Se2 alloy with the tungsten content, which was conducted by combining experimental and theoretical methods. Employed spectroscopic techniques, namely, photoreflectance, photoacoustic spectroscopy, and photoluminescence, allowed observing indirect and direct transitions at high and beyond high-symmetry points of the Brillouin zone (BZ). Two excitons (A and B) associated with the K point of the BZ were observed together with other optical transitions (C and D) related to band nesting. Moreover, we have also identified the indirect transition for the studied crystals. Obtained energies for all transitions were tracked with a tungsten content and compared with results of calculations performed within density functional theory. Furthermore, based on the mentioned comparison, optical transitions were assigned to specific regions of the BZ. Finally, we have obtained bowing parameters for experimentally observed features, for, i.e., thin-film samples: b(A) = 0.13 ± 0.03 eV, b(B) = 0.14 ± 0.03 eV, b(C) = 0.044 ± 0.008 eV, and b(D) = 0.010 ± 0.003 eV.
| S-EPMC8340422 | biostudies-literature
Project description:Despite the improved conversion efficiency of Cu2(ZnSn)Se4 (CZTSe) solar cells, their roll-to-roll fabrication nonetheless leads to low performance. The selenization time and temperature are typically considered major parameters for a powder-based CZTSe film; meanwhile, the importance of the densification during the roll-to-roll process is often overlooked. The densification process is related to the porosity of the light-absorbing layer, where high porosity lowers cell performance. In this study, we fabricated a dense CZTSe absorber layer as a method of controlling the compression of a powder precursor (Cu1.7(Zn1.2Sn1.0)S4.0 (CZTS)) during the roll-press process. The increased particle packing density of the CZTS layer was crucial in sintering the powder layer into a dense film and preventing severe selenization of the Mo back electrode. The pressed absorber layer of the CZTSe solar cell exhibited a more uniform chemical composition determined using dynamic secondary ion mass spectrometry (SIMS). Under the AM 1.5G illumination condition, the power conversion efficiency of the pressed solar cell was 6.82%, while the unpressed one was 4.90%.
| S-EPMC9921508 | biostudies-literature
Project description:In this work, the Raman spectroscopy mapping technique is used for the analysis of mechanical strain in Bi2Se3 thin films of various (3-400 nm) thicknesses synthesized by physical vapour deposition on amorphous quartz and single-layer graphene substrates. The evaluation of strain effects is based on the correlation analysis of in-plane (E2 g) and out-of-plane (A2 1g) Raman mode positions. For Bi2Se3 films deposited on quartz, experimental datapoints are scattered along the line with a slope of ∼0.85, related to the distribution of hydrostatic strain. In contrast to quartz/Bi2Se3 samples, for graphene/Bi2Se3 heterostructures with the same thicknesses, an additional negative slope of ∼-0.85, which can be associated with the distribution of the in-plane (a-b) biaxial tensile strain due to the film-substrate lattice mismatch, is observed. The algorithm of phonon deformation potential (PDP) calculation based on the proposed strain analysis for the 3 nm thick Bi2Se3 film deposited on the graphene substrate, where the strain is considered to be coherent across the thickness, is demonstrated. The PDPs for biaxial in-plane strain of the Bi2Se3 3 nm film in in-plane and out-of-plane modes are equal to -7.64 cm-1/% and -6.97 cm-1/%, respectively.
| S-EPMC9419075 | biostudies-literature
Project description:We studied the modal contributions to heat conduction at crystalline Si and crystalline Ge interfaces and found that more than 15% of the interface conductance arises from less than 0.1% of the modes in the structure. Using the recently developed interface conductance modal analysis (ICMA) method along with a new complimentary methodology, we mapped the correlations between modes, which revealed that a small group of interfacial modes, which exist between 12-13 THz, exhibit extremely strong correlation with other modes in the system. It is found that these interfacial modes (e.g., modes with large eigen vectors for interfacial atoms) are enabled by the degree of anharmonicity near the interface, which is higher than in the bulk, and therefore allows this small group of modes to couple to all others. The analysis sheds light on the nature of localized vibrations at interfaces and can be enlightening for other investigations of localization.
| S-EPMC4793224 | biostudies-literature
Project description:Monolayer MX2 (M = Mo, W; X = S, Se) has recently been drawn much attention due to their application possibility as well as the novel valley physics. On the other hand, it is also important to understand the electronic structures of bulk MX2 for material applications since it is very challenging to grow large size uniform and sustainable monolayer MX2. We performed angle-resolved photoemission spectroscopy and tight binding calculations to investigate the electronic structures of bulk 2H-MX2. We could extract all the important electronic band parameters for bulk 2H-MX2, including the band gap, direct band gap size at K (-K) point and spin splitting size. Upon comparing the parameters for bulk 2H-MX2 (our work) with mono- and multi-layer MX2 (published), we found that stacked layers, substrates for thin films, and carrier concentration significantly affect the parameters, especially the band gap size. The origin of such effect is discussed in terms of the screening effect.
| S-EPMC5090988 | biostudies-literature
Project description:The performance of Cu2ZnSn(S,Se)4 thin-film solar cells, commonly referred to as kesterite or CZTSSe, is limited by open-circuit voltage (VOC) values less than 60% of the maximum theoretical limit. In the present study, we employ energy-filtered photoemission microscopy to visualize nanoscale shunting paths in solution-processed CZTSSe films, which limit the VOC of cells to approximately 400 mV. These studies unveil areas of local effective work function (LEWF) narrowly distributed around 4.9 eV, whereas other portions show hotspots with LEWF as low as 4.2 eV. Localized valence band spectra and density functional theory calculations allow rationalizing the LEWF maps in terms of the CZTSSe effective work function broadened by potential energy fluctuations and nanoscale Sn(S,Se) phases.
| S-EPMC6215027 | biostudies-literature
Project description:For kesterite copper zinc tin sulfide/selenide (CZTSSe) solar cells to enter the market, in addition to efficiency improvements, the technological capability to produce flexible and large-area modules with homogeneous properties is necessary. Here, we report a greater than 10% efficiency for a cell area of approximately 0.5?cm2 and a greater than 8% efficiency for a cell area larger than 2?cm2 of certified flexible CZTSSe solar cells. By designing a thin and multi-layered precursor structure, the formation of defects and defect clusters, particularly tin-related donor defects, is controlled, and the open circuit voltage value is enhanced. Using statistical analysis, we verify that the cell-to-cell and within-cell uniformity characteristics are improved. This study reports the highest efficiency so far for flexible CZTSSe solar cells with small and large areas. These results also present methods for improving the efficiency and enlarging the cell area.
| S-EPMC6609618 | biostudies-literature
Project description:It is well-known that the alkali doping of polycrystalline Cu2ZnSn(S,Se)4 (CZTSSe) and Cu(In,Ga)(Se,S)2 has a beneficial influence on the device performance and there are various hypotheses about the principles of performance improvement. This work clearly explains the effect of Na doping on the fill factor (FF) rather than on all of the solar cell parameters (open-circuit voltage, FF, and sometimes short circuit current) for overall performance improvement. When doping is optimized, the fabricated device shows sufficient built-in potential and selects a better carrier transport path by the high potential difference between the intragrains and the grain boundaries. On the other hand, when doping is excessive, the device shows low contact potential difference and FF and selects a worse carrier transport path even though the built-in potential becomes stronger. The fabricated CZTSSe solar cell on a flexible metal foil optimized with a 25 nm thick NaF doping layer achieves an FF of 62.63%, thereby clearly showing the enhancing effect of Na doping.
| S-EPMC7610331 | biostudies-literature
Project description:A main concern of the promising DMF-based Cu2 ZnSn(Sx ,Se1- x )4 (CZTSSe) solar cells lies in the absence of a large-grain spanning structure, which is a key factor for high open-circuit voltage (Voc ) and power conversion efficiency (PCE). A new strategy to achieve CZTSSe large-grain spanning monolayer is proposed, by taking advantage of the synergistic optimization with a Cu2+ plus Sn2+ redox system and pre-annealing temperatures. A series of structural, morphological, electrical, and photoelectric characterizations are employed to study the effects of the pre-annealing temperatures on absorber qualities, and an optimized temperature of 430 ℃ is determined. The growth mechanism of the large-grain spanning monolayer and the effect of redox reaction rate are carefully investigated. Three types of absorber growth mechanisms and a concept of critical temperature are proposed. The devices based on this large-grain spanning monolayer suppress the recombination of carriers at crystal boundaries and interfaces. The champion device exhibits a high Voc (>500 mV) and PCE of 11.76%, which are both the maximum values among DMF-based solar cells at the current stage.
| S-EPMC9284129 | biostudies-literature