Browse
Submit Data
Databases
API
Help

Dataset Information

16 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

N,N′-Bis(3-methylphenyl)-N,N′-dyphenylbenzidine Based Distributed Feedback Lasers with Holographically Fabricated Polymeric Resonators

ABSTRACT: The molecule N,N′-bis(3-methylphenyl)-N,N′-dyphenylbenzidine (TPD) has been widely used in optoelectronic applications, mainly for its hole-transporting properties, but also for its capability to emit blue light and amplified spontaneous emission, which is important for the development of organic lasers. Here, we report deep-blue-emitting distributed feedback (DFB) lasers based on TPD dispersed in polystyrene (PS), as active media, and dichromated gelatin layers with holographically engraved relief gratings, as laser resonators. The effect of the device architecture (with the resonator located below or on top of the active layer) is investigated with a dye (TPD) that can be doped into PS at higher rates (up to 60 wt%), than with previously used dyes (<5 wt%). This has enabled changing the index contrast between film and resonator, which has an important effect on the laser performance. With regards to thresholds, both architectures behave similarly for TPD concentrations above 20 wt%, while for lower concentrations, top-layer resonator devices show lower values (around half). Remarkably, the operational durability of top-layer resonator devices is larger (in a factor of around 2), independently of the TPD concentration. This is a consequence of the protection offered by the resonator against dye photo-oxidation when the device is illuminated with pulsed UV light.

SUBMITTER: Bonal V

PROVIDER: S-EPMC8587923 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Green Perovskite Distributed Feedback Lasers.

Project description:A visible perovskite distributed feedback laser is fabricated for the first time. Through the use of nanocrystal pinning, highly luminescent methylammonium lead bromide films are used to produce stable lasers emitting at 550?nm, with a low threshold of 6 µJcm-2. The lasers were able to support multiple polarisations, and could be switched between transverse magnetic and transverse electric mode operation through simple tuning of the distributed feedback grating period.

| S-EPMC5601482 | biostudies-literature

Solution-processed nanographene distributed feedback lasers.

Project description:The chemical synthesis of nanographene molecules constitutes the bottom-up approach toward graphene, simultaneously providing rational chemical design, structure-property control and exploitation of their semiconducting and luminescence properties. Here, we report nanographene-based lasers from three zigzag-edged polycyclic aromatics. The devices consist of a passive polymer film hosting the nanographenes and a top-layer polymeric distributed feedback resonator. Both the active material and the laser resonator are processed from solution, key for the purpose of obtaining low-cost devices with mechanical flexibility. The prepared lasers show narrow linewidth ( < 0.13 nm) emission at different spectral regions covering a large segment of the visible spectrum, and up to the vicinity of the near-infrared. They show outstandingly long operational lifetimes (above 105 pump pulses) and very low thresholds. These results represent a significant step forward in the field of graphene and broaden its versatility in low-cost devices implying light emission, such as lasers.

| S-EPMC6658550 | biostudies-literature

Distributed Feedback Lasers by Thermal Nanoimprint of Perovskites Using Gelatin Gratings.

Project description:To date, thermal nanoimprint lithography (NIL) for patterning hybrid perovskites has always involved an intricate etching step of a hard stamp material or its master. Here, we demonstrate for the first time the successful nanopatterning of a perovskite film by NIL with a low-cost polymeric stamp. The stamp consists of a dichromated gelatin grating structured by holographic lithography. The one-dimensional grating is imprinted into a perovskite film at 95 °C and 90 MPa for 10 min, resulting in a high quality second-order distributed feedback (DFB) laser. The laser exhibits an excellent performance with a threshold of 81 μJ/cm2, a line width of 0.32 nm, and a pronounced linear polarization. This novel approach enables cost-effective fabrication of high-quality DFB lasers compatible with different perovskite compositions and photonic nanostructures for a wide range of applications.

| S-EPMC9940720 | biostudies-literature

Highly efficient surface-emitting semiconductor lasers exploiting quasi-crystalline distributed feedback photonic patterns.

Project description:Quasi-crystal distributed feedback lasers do not require any form of mirror cavity to amplify and extract radiation. Once implemented on the top surface of a semiconductor laser, a quasi-crystal pattern can be used to tune both the radiation feedback and the extraction of highly radiative and high-quality-factor optical modes that do not have a defined symmetric or anti-symmetric nature. Therefore, this methodology offers the possibility to achieve efficient emission, combined with tailored spectra and controlled beam divergence. Here, we apply this concept to a one-dimensional quantum cascade wire laser. By lithographically patterning a series of air slits with different widths, following the Octonacci sequence, on the top metal layer of a double-metal quantum cascade laser operating at THz frequencies, we can vary the emission from single-frequency-mode to multimode over a 530-GHz bandwidth, achieving a maximum peak optical power of 240 mW (190 mW) in multimode (single-frequency-mode) lasers, with record slope efficiencies for multimode surface-emitting disordered THz lasers up to ≈570 mW/A at 78 K and ≈720 mW/A at 20 K and wall-plug efficiencies of η ≈ 1%.

| S-EPMC7142150 | biostudies-literature

Controlling the emission properties of solution-processed organic distributed feedback lasers through resonator design.

Project description:Surface-emitting distributed feedback (DFB) lasers with both, resonator and active material based on solution-processable polymers, are attractive light sources for a variety of low-cost applications. Besides, the lasers should have competitive characteristics compared to devices based on high-quality inorganic resonators. Here, we report high performing all-solution-processed organic DFB lasers, consisting of water-processed photoresist layers with surface relief gratings located over the active films, whose emission properties can be finely tuned through resonator design. Their laser threshold and efficiency are simultaneously optimized by proper selection of residual resist thickness and grating depth, d. Lowest thresholds and largest efficiencies are obtained when there is no residual layer, while a trade-off between threshold and efficiency is found in relation to d, because both parameters decrease with decreasing d. This behaviour is successfully explained in terms of an overlap factor r, defined to quantify the interaction strength between the grating and the light emitted by the active film and traveling along it, via the evanescent field. It is found that optimal grating depths are in the range 100-130 nm (r ~ 0.5-0.4). Overall, this study provides comprehensive design rules towards an accurate control of the emission properties of the reported lasers.

| S-EPMC6671999 | biostudies-literature

Broadband high-Q multimode silicon concentric racetrack resonators for widely tunable Raman lasers.

Project description:Multimode silicon resonators with ultralow propagation losses for ultrahigh quality (Q) factors have been attracting attention recently. However, conventional multimode silicon resonators only have high Q factors at certain wavelengths because the Q factors are reduced at wavelengths where fundamental modes and higher-order modes are both near resonances. Here, by implementing a broadband pulley directional coupler and concentric racetracks, we present a broadband high-Q multimode silicon resonator with average loaded Q factors of 1.4 × 106 over a wavelength range of 440 nm (1240-1680 nm). The mutual coupling between the two multimode racetracks can lead to two supermodes that mitigate the reduction in Q factors caused by the mode coupling of the higher-order modes. Based on the broadband high-Q multimode resonator, we experimentally demonstrated a broadly tunable Raman silicon laser with over 516 nm wavelength tuning range (1325-1841 nm), a threshold power of (0.4 ± 0.1) mW and a slope efficiency of (8.5 ± 1.5) % at 25 V reverse bias.

| S-EPMC9209424 | biostudies-literature

High-coherence semiconductor lasers based on integral high-Q resonators in hybrid Si/III-V platforms.

Project description:The semiconductor laser (SCL) is the principal light source powering the worldwide optical fiber network. The ever-increasing demand for data is causing the network to migrate to phase-coherent modulation formats, which place strict requirements on the temporal coherence of the light source that no longer can be met by current SCLs. This failure can be traced directly to the canonical laser design, in which photons are both generated and stored in the same, optically lossy, III-V material. This leads to an excessive and large amount of noisy spontaneous emission commingling with the laser mode, thereby degrading its coherence. High losses also decrease the amount of stored optical energy in the laser cavity, magnifying the effect of each individual spontaneous emission event on the phase of the laser field. Here, we propose a new design paradigm for the SCL. The keys to this paradigm are the deliberate removal of stored optical energy from the lossy III-V material by concentrating it in a passive, low-loss material and the incorporation of a very high-Q resonator as an integral (i.e., not externally coupled) part of the laser cavity. We demonstrate an SCL with a spectral linewidth of 18 kHz in the telecom band around 1.55 ?m, achieved using a single-mode silicon resonator with Q of 10(6).

| S-EPMC3939879 | biostudies-other

Class-C semiconductor lasers with time-delayed optical feedback.

Project description:We perform a linear stability analysis and numerical bifurcation diagrams of a class-C laser with time-delayed optical feedback. We employ a rate equation system based on the Maxwell-Bloch equations, and study the influence of the dephasing time on the laser dynamics. We find a stabilizing effect of an intermediate dephasing time, i.e. when moving from a class-B to a class-C laser. At long dephasing times, a destabilization of the laser solution occurs by a feedback-induced unlocking of Rabi oscillations at the second laser threshold. We predict an optimum resistance to time-delayed optical feedback for dephasing times close to the photon cavity lifetime. This article is part of the theme issue 'Nonlinear dynamics of delay systems'.

| S-EPMC6661328 | biostudies-literature

Optical fractal in cryogenic environments based on distributed feedback Bragg photonic crystals.

Project description:We studied the optical fractal effect of the one-dimensional distributed feedback Bragg photonic crystals formed by semiconductor GaAs and dielectric TiO2. Light wave is transmitted in the intermediate dielectric slab and reflected back by the periodic photonic crystals at both ends, forming multiple fractal resonance output. The transmission channels expand exponentially by thickening the bulk in a cryogenic environment. The quality factor of each fractal resonant state improves with a greater periodic number of crystals. Furthermore, central wave of resonance has a blue-shift as the external pressure increases, while the influence of environment temperature on the fractal resonance could be ignored. It is hoped that our study can highlight the potential of these findings for designing multi-channel communication filters in cryogenic environments.

| S-EPMC10513194 | biostudies-literature

Randomly Distributed Fabry-Perot-type Metal Nanowire Resonators and Their Lasing Action.

Project description:Optical feedback mechanisms are often obtained from well-defined resonator structures fabricated by top-down processes. Here, we demonstrate that two-dimensional networks of metallic nanowires dispersed on the semiconductor slab can provide strong in-plane optical feedback and, thus, form randomly-distributed Fabry-Pérot-type resonators that can achieve multi- or single-mode lasing action in the near infrared wavelengths. Albeit with their subwavelength-scale cross-sections and uncontrolled inter-nanowire distances, a cluster of nearly parallel metal nanowires acts as an effective in-situ reflector for the semiconductor-metal slab waveguide modes for coherent optical feedback in the lateral direction. Fabry-Pérot type resonance can be readily developed by a pair of such clusters coincidentally formed in the solution-processed random nanowire network. Our low-cost and large-area approach for opportunistic random cavity formation would open a new pathway for integrated planar light sources for low-coherence imaging and sensing applications.

| S-EPMC4840363 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data