Browse
Submit Data
Databases
API
Help

Dataset Information

19 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Shear-Induced Crystallization of Star and Linear Poly(L-lactide)s

ABSTRACT: The influence of macromolecular architecture on shear-induced crystallization of poly(L-lactide) (PLLA) was studied. To this aim, three star PLLAs, 6-arm with Mw of 120 and 245 kg/mol, 4-arm with Mw of 123 kg/mol, and three linear PLLAs with Mw of 121, 240 and 339 kg/mol, were synthesized and examined. The PLLAs were sheared at 170 and 150 °C, at 5/s, 10/s and 20/s for 20 s, 10 s and 5 s, respectively, and then cooled at 10 or 30 °C/min. Shear-induced crystallization during cooling was followed by a light depolarization method, whereas the crystallized specimens were examined by DSC, 2D-WAXS, 2D-SAXS and SEM. The effect of shear depended on the shearing conditions, cooling rate and polymer molar mass but it was also affected by the macromolecular architecture. The shear-induced crystallization of linear PLLA with Mw of 240 kg/mol was more intense than that of the 6-arm polymer with similar Mw, most possibly due to its higher Mz. However, the influence of shear on the crystallization of the star polymers with Mw close to 120 kg/mol was stronger than on that of their linear analog. This was reflected in higher crystallization temperature, as well as crystallinity achieved during cooling.

SUBMITTER: Bojda J

PROVIDER: S-EPMC8588257 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

The Effect of Thermal History on the Fast Crystallization of Poly(l-Lactide) with Soluble-Type Nucleators and Shear Flow.

Project description:The N?,N?'-(ethane-1,2-diyl)bis(N?-phenyloxalamide) (OXA) is a soluble-type nucleator with a dissolving temperature of 230 °C in poly(l-lactic acid) (PLLA) matrix. The effect of thermal history and shear flow on the crystallization behavior of the PLLA/OXA samples was investigated by rheometry, polarized optical microscopy (POM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD), and scanning electron microscopy (SEM). The crystallization process of the PLLA/OXA-240 sample (i.e., pre-melted at 240 °C) was significantly promoted by applying a shear flow, e.g., the onset crystallization time (tonset) of the PLLA at 155 °C was reduced from 1600 to 200 s after shearing at 0.4 rad/s for even as short as 1.0 s, while the crystallinity (Xc) was increased to 40%. Moreover, the tonset of the PLLA/OXA-240 sample is 60%?80% lower than that of the PLLA/OXA-200 sample (i.e., pre-melted at 200 °C) with a total shear angle of 2 rad, indicating a much higher crystallization rate of the PLLA/OXA-240 sample. A better organization and uniformity of OXA fibrils can be obtained due to a complete pre-dissolution in the PLLA matrix followed by shear and oscillation treatments. The well dispersed OXA fibrils and flow-induced chain orientation are mainly responsible for the fast crystallization of the PLLA/OXA-240 samples. In addition, the shear flow created some disordered ?'-form crystals in the PLLA/OXA samples regardless of the thermal history (200 or 240 °C).

| S-EPMC6432256 | biostudies-literature

Crystallization of a Self-Assembling Nucleator in Poly(l-lactide) Melt.

Project description:In the present work, crystallization of a soluble nucleator N, N', N″-tricyclohexyl-1,3,5-benzenetricarboxylamide (TMC-328) in a poly(l-lactic acid) (PLLA) matrix has been studied at different temperatures. Based on the change in solubility with temperature, different levels of supersaturation of TMC-328 in a PLLA matrix can be obtained. This nucleator presents a fibrous structure produced via self-assembling and develops into an interconnected network when the temperature is lowered. The TMC-328 crystal nuclei density is quantified via optical microscopy, using the average distance of the adjacent fibrillar structure, which shows a steady decrease with the decrease in temperature. The crystallization rates of TMC-328 were assessed through rheological measurements of network formation. Both fibrils' density and crystallization kinetics display a power law dependence on supersaturation. For the first time, the solid-melt interfacial energy, the size of the critical nucleus, and the number of molecules making up the critical nucleus of the nucleator TMC-328 in the PLLA matrix have been determined by adopting the classical nucleation theory. The subsequent crystallization of PLLA induced by this nucleator was investigated as a function of the fibrils' spatial density. The crystallization rate of PLLA is enhanced with the increase in the TMC-328 fibrils' density because of the availability of a larger nucleating surface. The self-assembled fibril of TMC-328 can serve as shish to form a hybrid shish-kebab structure after the crystallization of PLLA, regardless of the number of nucleation sites.

| S-EPMC8499044 | biostudies-literature

Homocrystallization and Stereocomplex Crystallization Behaviors of As-Spun and Hot-Drawn Poly(l-lactide)/Poly(d-lactide) Blended Fibers During Heating.

Project description:A series of poly(l-lactide)/poly(d-lactide) blended chips (LDC), as-spun LD fibers (LDA) and hot-drawn LD fibers (LDH) were prepared for investigating the homocrystallization and stereocomplex crystallization behaviors of LDA and LDH fibers during heating. Modulated differential scanning calorimetry (MDSC), hot stage polarized microscopy (HSPM), and real-time wide-angle X-ray diffraction (WAXD) were used for studying the crystallization and melting behaviors, fiber morphology, and crystalline structure evolution of the LDA and LDH fibers' homocrystals and stereocomplex crystals during heating. The molecular chain orientations of the LDA and LDH fibers were obtained through spinning and improved through the hot drawing processes. When the molecular chain was oriented on the fiber axis, the homocrystals and stereocomplex crystals of the fibers began to form in turn as the heating temperature exceeded the glass transition temperature of the fiber. The side-by-side packing of the molecular chains was promoted by mixing the molecular chains with the extrusion screw during the spinning process, facilitating stereocomplex crystallization. When the LDA fiber was heated above the glass transition temperature of the fiber, movement of the fiber molecular chain-including molecular chain orientation and relaxation, as well as crystallization, melting, and recrystallization of homocrystals and stereocomplex crystals-were investigated through HSPM. MDSC and real-time WAXD were used to observe the molecular chains of the melted poly(l-lactide) and poly(d-lactide) homocrystals of the fibers rearranging and transiting to form stereocomplex crystals during heating.

| S-EPMC6780053 | biostudies-literature

Crystallization and Properties of Poly(lactide)/Poly(δ-valerolactone) Alternating Supramolecular Copolymers Adjusted by Stereocomplexation.

Project description:The crystallization behavior of a series of synthesized polylactide (PLA)/poly(δ-valerolactone) (PVL) supramolecular copolymers with 2-ureido-4[1H]-pyrimidinone (UPy) groups is investigated by differential scanning calorimetry and X-ray diffraction. The stereocomplexation of PLA-based supramolecular polymers (SMPs) is strongly related to the block length, L/D ratios, and the UPy groups. Both the increase of the PLA block length and the self-complementary hydrogen bonding of the UPy end groups restrain the crystallization of the PVL blocks. The stereocomplexation of PLA-SMPs is greatly promoted by UPy groups, while the homocrystallization of PLA is constrained. The dynamic mechanical analysis indicated that the enhanced stereocomplexation would lead to higher thermal resistance and mechanical properties of PLA-based SMPs.

| S-EPMC6648093 | biostudies-literature

Functionalized Boron Nitride Nanosheets/Poly(l-lactide) Nanocomposites and Their Crystallization Behavior.

Project description:In this work, hydroxyl-functionalized boron nitride nanosheet (OH-BNNS) was prepared and was blended with poly(l-lactide) (PLLA) to yield PLLA/OH-BNNS nanocomposites with excellent dispersion of OH-BNNS via the interaction of carbonyl in PLLA and hydroxyl in OH-BNNS. The effects of OH-BNNS on the crystallization and melting behaviors, isothermal crystallization kinetics, macroscopic crystal morphology and crystal structure of PLLA were studied by means of various techniques. The addition of OH-BNNS nanofillers can effectively accelerate the crystallization of PLLA and enhance the nucleation density, leading to a smaller spherulite size, increased crystallinity, a more obvious crystallization peak upon cooling but weakened cold crystallization behavior upon heating. Low OH-BNNS loading can increase the relative content of α-crystal, but the relative content of less perfect α'-crystal is increased at high OH-BNNS loading due to the strong interaction between PLLA and OH-BNNS.

| S-EPMC6473543 | biostudies-literature

Poly(lactide)-g-poly(butylene succinate-co-adipate) with High Crystallization Capacity and Migration Resistance.

Project description:Plasticized polylactide (PLA) with increased crystallization ability and prolonged life-span in practical applications due to the minimal plasticizer migration was prepared. Branched plasticized PLA was successfully obtained by coupling poly(butylene succinate-co-adipate) (PBSA) to crotonic acid (CA) functionalized PLA. The plasticization behavior of PBSA coupled PLA (PLA-CA-PBSA) and its counterpart PBSA blended PLA (PLA/PBSA) were fully elucidated. For both PLA-CA-PBSA and PLA/PBSA, a decrease of Tg to around room temperature and an increase in the elongation at break of PLA from 14% to 165% and 460%, respectively, were determined. The crystallinity was increased from 2.1% to 8.4% for PLA/PBSA and even more, to 10.6%, for PLA-CA-PBSA. Due to the inherent poor miscibility between the PBSA and PLA, phase separation occurred in the blend, while PLA-CA-PBSA showed no phase separation which, together with the higher crystallinity, led to better oxygen barrier properties compared to neat PLA and PLA/PBSA. A higher resistance to migration during hydrolytic degradation for the PLA-CA-PBSA compared to the PLA/PBSA indicated that the plasticization effect of PBSA in the coupled material would be retained for a longer time period.

| S-EPMC5503035 | biostudies-other

Ring-opening polymerization-induced crystallization-driven self-assembly of poly-L-lactide-block-polyethylene glycol block copolymers (ROPI-CDSA).

Project description:The self-assembly of block copolymers into 1D, 2D and 3D nano- and microstructures is of great interest for a wide range of applications. A key challenge in this field is obtaining independent control over molecular structure and hierarchical structure in all dimensions using scalable one-pot chemistry. Here we report on the ring opening polymerization-induced crystallization-driven self-assembly (ROPI-CDSA) of poly-L-lactide-block-polyethylene glycol block copolymers into 1D, 2D and 3D nanostructures. A key feature of ROPI-CDSA is that the polymerization time is much shorter than the self-assembly relaxation time, resulting in a non-equilibrium self-assembly process. The self-assembly mechanism is analyzed by cryo-transmission electron microscopy, wide-angle x-ray scattering, Fourier transform infrared spectroscopy, and turbidity studies. The analysis revealed that the self-assembly mechanism is dependent on both the polymer molecular structure and concentration. Knowledge of the self-assembly mechanism enabled the kinetic trapping of multiple hierarchical structures from a single block copolymer.

| S-EPMC7499262 | biostudies-literature

Comparison of Cyclic and Linear Poly(lactide)s Using Small-Angle Neutron Scattering.

Project description:Small-angle neutron scattering (SANS) experiments were conducted on cyclic and linear polymers of racemic and l-lactides (PLA) with the goal of comparing chain configurations, scaling, and effective polymer-solvent interactions of the two topologies in acetone-d 6 and THF-d 8. There are limited reports of SANS results on cyclic polymers due to the lack of substantial development in the field until recently. Now that pure, well-defined cyclic polymers are accessible, unanswered questions about their rheology and physical conformations can be better investigated. Previously reported SANS experiments have used cyclic and linear polystyrene samples; therefore, our work allowed for direct comparison using a contrasting (structurally and sterically) polymer. We compared SANS results of cyclic and linear PLA samples with various microstructures and molecular weights at two different temperatures, allowing for comparison with a wide range of variables. The results followed the trends of previous experiments, but much greater differences in the effective polymer-solvent interaction parameters between cyclic and linear forms of PLA were observed, implying that the small form factor and hydrogen bonding in PLA allowed for much more compact conformations in the cyclic form only. Also, the polymer microstructure was found to influence polymer-solvent interaction parameters substantially. These results illustrate how the difference in polymer-solvent interactions between cyclic and linear polymers can vary greatly depending on the polymer in question and the potential of neutron scattering as a tool for identification and characterization of the cyclic topology.

| S-EPMC9798859 | biostudies-literature

Study of the Molecular Dynamics of Multiarm Star Polymers with a Poly(ethyleneimine) Core and Poly(lactide) Multiarms.

Project description:Multiarm star polymers, denoted PEIx-PLAy and containing a hyperbranched poly(ethyleneimine) (PEI) core of different molecular weights x and poly(lactide) (PLA) arms with y ratio of lactide repeat units to N links were used in this work. Samples were preconditioned to remove the moisture content and then characterized by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and dielectric relaxation spectroscopy (DRS). The glass transition temperature, Tg, is between 48 and 50 °C for all the PEIx-PLAy samples. The dielectric curves show four dipolar relaxations: γ, β, α, and α' in order of increasing temperature. The temperatures at which these relaxations appear, together with their dependence on the frequency, allows relaxation maps to be drawn, from which the activation energies of the sub-Tg γ- and β-relaxations and the Vogel-Fulcher-Tammann parameters of the α-relaxation glass transition are obtained. The dependence of the characteristic features of these relaxations on the molecular weight of the PEI core and on the ratio of lactide repeat units to N links permits the assignation of molecular motions to each relaxation. The γ-relaxation is associated with local motions of the -OH groups of the poly(lactide) chains, the β-relaxation with motions of the main chain of poly(lactide), the α-relaxation with global motions of the complete assembly of PEI core and PLA arms, and the α'-relaxation is related to the normal mode relaxation due to fluctuations of the end-to-end vector in the PLA arms, without excluding the possibility that it could be a Maxwell-Wagner-Sillars type ionic peak because the material may have nano-regions of different conductivity.

| S-EPMC5459105 | biostudies-other

Preparation of Doxorubicin-Loaded Amphiphilic Poly(D,L-Lactide-Co-Glycolide)-b-Poly(N-Acryloylmorpholine) AB2 Miktoarm Star Block Copolymers for Anticancer Drug Delivery.

Project description:Owing to their unique topology and physical properties, micelles based on miktoarm amphiphilic star block copolymers play an important role in the biomedical field for drug delivery. Herein, we developed a series of AB2-type poly(D,L-lactide-co-glycolide)-b-poly(N-acryloyl morpholine) (PLGA-b-PNAM2) miktoarm star block copolymers by reversible addition-fragmentation chain-transfer polymerization and ring-opening copolymerization. The resulting miktoarm star polymers were investigated by 1H NMR spectroscopy and gel permeation chromatography. The critical micellar concentration value of the micelles increases with an increase in PNAM block length. As revealed by transmission electron microscopy and dynamic light scattering, the amphiphilic miktoarm star block copolymers can self-assemble to form spherical micellar aggregates in water. The anticancer drug doxorubicin (DOX) was encapsulated by polymeric micelles; the drug-loading efficiency and drug-loading content of the DOX-loaded micelles were 81.7% and 9.1%, respectively. Acidic environments triggered the dissociation of the polymeric micelles, which led to the more release of DOX in pH 6.4 than pH 7.4. The amphiphilic PLGA-b-PNAM2 miktoarm star block copolymers may have broad application as nanocarriers for controlled drug delivery.

| S-EPMC7504487 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data