Chemical Emissions from Cured and Uncured 3D-Printed Ventilator Patient Circuit Medical Parts.
Ontology highlight
ABSTRACT:
SUBMITTER: Krechmer JE
PROVIDER: S-EPMC8600644 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:OBJECTIVES:To optimize the 3D printing of a dental material for provisional crown and bridge restorations using a low-cost stereolithography 3D printer; and compare its mechanical properties against conventionally cured provisional dental materials. METHODS:Samples were 3D printed (25×2×2mm) using a commercial printable resin (NextDent C&B Vertex Dental) in a FormLabs1+ stereolithography 3D printer. The printing accuracy of printed bars was determined by comparing the width, length and thickness of samples for different printer settings (printing orientation and resin color) versus the set dimensions of CAD designs. The degree of conversion of the resin was measured with FTIR, and both the elastic modulus and peak stress of 3D printed bars was determined using a 3-point being test for different printing layer thicknesses. The results were compared to those for two conventionally cured provisional materials (Integrity®, Dentsply; and Jet®, Lang Dental Inc.). RESULTS:Samples printed at 90° orientation and in a white resin color setting was chosen as the most optimal combination of printing parameters, due to the comparatively higher printing accuracy (up to 22% error), reproducibility and material usage. There was no direct correlation between printing layer thickness and elastic modulus or peak stress. 3D printed samples had comparable modulus to Jet®, but significantly lower than Integrity®. Peak stress for 3D printed samples was comparable to Integrity®, and significantly higher than Jet®. The degree of conversion of 3D printed samples also appeared higher than that of Integrity® or Jet®. SIGNIFICANCE:Our results suggest that a 3D printable provisional restorative material allows for sufficient mechanical properties for intraoral use, despite the limited 3D printing accuracy of the printing system of choice.
| S-EPMC5801146 | biostudies-literature
Project description:We demonstrate the viability of using ultra-thin sheets of microbially grown nanocellulose to build functional medical sensors. Microbially grown nanocellulose is an interesting alternative to plastics, as it is hydrophilic, biocompatible, porous, and hydrogen bonding, thereby allowing the potential development of new application routes. Exploiting the distinguishing properties of this material enables us to develop solution-based processes to create nanocellulose printed circuit boards, allowing a variety of electronics to be mounted onto our nanocellulose. As proofs of concept, we have demonstrated applications in medical sensing such as heart rate monitoring and temperature sensing-potential applications fitting the wide-ranging paradigm of a future where the Internet of Things is dominant.
| S-EPMC7181041 | biostudies-literature
Project description:Chemistry digitization requires an unambiguous link between experiments and the code used to generate the experimental conditions and outcomes, yet this process is not standardized, limiting the portability of any chemical code. What is needed is a universal approach to aid this process using a well-defined standard that is composed of syntheses that are employed in modular hardware. Herein we present a new approach to the digitization of organic synthesis that combines process chemistry principles with 3D printed reactionware. This approach outlines the process for transforming unit operations into digitized hardware and well-defined instructions that ensure effective synthesis. To demonstrate this, we outline the process for digitizing 3 MIDA boronate building blocks, an ester hydrolysis, a Wittig olefination, a Suzuki-Miyaura coupling reaction, and synthesis of the drug sulfanilamide.
| S-EPMC9186708 | biostudies-literature
Project description:While the technology is relatively new, low-cost 3D printing has impacted many aspects of human life. 3D printers are being used as manufacturing tools for a wide variety of devices in a spectrum of applications ranging from diagnosis to implants to external prostheses. The ease of use, availability of 3D-design software and low cost has made 3D printing an accessible manufacturing and fabrication tool in many bioanalytical research laboratories. 3D printers can print materials with varying density, optical character, strength and chemical properties that provide the user with a vast array of strategic options. In this review, we focus on applications in biomedical diagnostics and how this revolutionary technique is facilitating the development of low-cost, sensitive, and often geometrically complex tools. 3D printing in the fabrication of microfluidics, supporting equipment, and optical and electronic components of diagnostic devices is presented. Emerging diagnostics systems using 3D bioprinting as a tool to incorporate living cells or biomaterials into 3D printing is also reviewed.
| S-EPMC6187244 | biostudies-literature
Project description:A 96-well microplate reader for absorption spectroscopy was designed, constructed, and tested at a total cost of ca. 500 USD. The reduced cost of the device represents the major technical contribution of this manuscript, as costs were reduced 7 fold from previous reports. The device was able to achieve 3σ limits of detection of ca. 0.01 absorbance units (AU) over a 60 second measurement for the mid-visible wavelength range. Component parts are either commercially available, or 3D printed from plans. Analysis wavelength can be altered throughout the visible region through use of various photographic or theatrical filters. This feature allows the well plate reader to be used for typical laboratory assays such as cell population estimation by optical density (OD) at 600 nm, or enzyme-linked immunosorbent assays (ELISA) at 450 nm. This manuscript reports on the motivation and process of constructing the device, lists required parts, presents data demonstrating device function, and provides the community of scholars with plans to reproduce the work. The device can be reproduced in laboratories lacking sufficient resources to purchase commercially available options and this outcome contributes towards empowerment of individuals and equity of scientific enquiry.
| S-EPMC9103534 | biostudies-literature
Project description:In this paper, the post-processing of 3D-printed poly lactic acid (PLA) parts is investigated. Workpieces are manufactured by fused deposition modeling (FDM) 3D printing, while they may have defects in some areas such as edges. A post-processing is introduced here for 3D-printed samples by low power CO2 laser. The thickness of the FDM samples are 3.2 mm and printed by optimum conditions. Effects of process parameters such as focal plane position (-3.2-3.2 mm), laser power (20-40 W), and laser cutting speed (1-13 mm/s) are examined based on the design of experiments (DOE). Geometrical features of the kerf; top and bottom kerf; taper; ratio of top to the bottom kerf are considered as output responses. An analysis of the experimental results by statistical software is conducted to survey the effects of process parameters and to obtain regression equations. By optimizing of the laser cutting process; an appropriate kerf quality is obtained and also optimum input parameters are suggested. Experimental verification tests show a good agreement between empirical results and statistical predictions. The best optimum sample with 1.19 mm/s cutting speed, 36.49 W power and 0.53 mm focal plane position shows excellent physical features after the laser cutting process when 276.9 ?m top and 261.5 ?m bottom kerf width is cut by laser.
| S-EPMC7182925 | biostudies-literature
Project description:In this paper, we present a technique for increasing the strength of thermoplastic fused deposition manufactured printed parts while retaining the benefits of the process such as ease, speed of implementation, and complex part geometries. By carefully placing voids in the printed parts and filling them with high-strength resins, we can improve the overall part strength and stiffness by up to 45% and 25%, respectively. We discuss the process parameters necessary to use this strengthening technique and the theoretically possible strength improvements to bending beam members. We then show three-point bend testing data comparing solid printed ABS samples with those strengthened through the fill compositing process, as well as examples of 3D printed parts used in real-world applications.
| S-EPMC4400136 | biostudies-literature
Project description:With the ability to create customizable products tailored to individual patients, the use of 3D printed medical devices has rapidly increased in recent years. Despite such interest in these materials, a risk assessment based on the material characterization of final device extracts-as per regulatory guidance-has not yet been completed, even though the printing process may potentially impact the leachability of polymer components. To further our understanding of the chemical impact of 3D printed medical devices, this study investigated the extractable profiles of four different materials, including a PLA polymer advertised as "FDA-approved". The fusion deposition modeling (FDM) printing process created distinct chemical and physical signatures in the extracts of certain materials. The application of an annealing procedure to printed devices led to a substantial decrease in extractable components by as much as a factor of 50. In addition, the use of a brass printing nozzle led to an increase in the amount of Pb detected in 3D printed device extracts. The data generated provides valuable information that can be used to help assess extractable risks of 3D printed medical devices, assist with future 3D printing designs, and may provide insight for agencies tasked with governing 3D printed medical device regulations.
| S-EPMC6530847 | biostudies-literature
Project description:BackgroundThe current coronavirus infectious disease 2019 (COVID-19) pandemic has caused unexpected pressure on medical supplies, interrupting supply chains and increasing prices. The supply of antiviral filters which form an essential part of the ventilator circuit have been affected by these issues. Three-dimensional (3D) printing may provide a solution to some of these issues.MethodsWe designed and tested 3D printed heat and moisture exchange (HME) and antiviral casing. For each casing we tested two different filter materials derived from a sediment water filter cartridge or 1.5-μm glass fiber filter paper. A polyurethane sponge was used for the HME. Each design was tested for circuit leak, circuit compliance, peak inspiratory pressure and casing integrity using methylene blue dye.ResultsWe designed, produced, and tested two different types of antiviral filters with six different internal configurations. Overall, we tested 10 modified filter designs and compared them with the original commercial filter. Except for the combination of 1.5-μm filter paper and 5 mm sponge peak inspiratory pressure and circuit compliance of the filters produced were within the operating limits of the ventilator. All In addition, all filters passed the dye test.ConclusionsOur filter may be of particular importance to those working in low middle-income countries unable to compete with stronger economies. Our design relies on products available outside the healthcare supply chain, much of which can be purchased in grocery stores, hardware stores, or industrial and academic institutions. We hope that these HMEs and viral filters may be beneficial to clinicians who face critical supply chain issues during the COVID-19 pandemic.
| S-EPMC8044501 | biostudies-literature
Project description:The utilization of polymer-based materials is quickly expanding. The enterprises of today are progressively seeking techniques to supplant metal parts with polymer-based materials as a result of their light weight, simple support and modest costs. The ceaselessly developing requirement for composite materials with new or enhanced properties brings about the preparation of different polymer mixes with various arrangements, morphologies and properties. Fused filament fabrication processes such as 3D-printing are nowadays shaping the actual pathway to a full pallet of materials, from art-craft to biomaterials. In this study, the structural and mechanical behavior of three types of commercially available filaments comprised of synthetic poly(acrylonitrile-co-butadiene-co-styrene) (ABS), poly(lactic acid) (PLA) and poly(lactic acid)/polyhydroxyalkanoate reinforced with bamboo wood flour composite (PLA/PHA BambooFill) were assessed through mechanical testing and optical microscopy, aiming to understand how the modifications that occur in the printed models with internal architecture are influencing the mechanical properties of the 3D-printed material. It has been determined that the material printed from PLA presents the highest compression strength, three-point bending and shock resistance, while the ABS shows the best tensile strength performance. A probability plot was used to verify the normality hypothesis of data for the tensile strength, in conjunction with the Anderson-Darling statistic test. The results of the statistic indicated that the data were normally distributed and that there is a marked influence of the internal architecture of the 3D-printed models on the mechanical properties of the printed material.
| S-EPMC7285309 | biostudies-literature