Browse
Submit Data
Databases
API
Help

Dataset Information

16 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Bioprinting of Collagen Type I and II via Aerosol Jet Printing for the Replication of Dense Collagenous Tissues.

ABSTRACT: Collagen has grown increasingly present in bioprinting, however collagen bioprinting has mostly been limited to the extrusion printing of collagen type I to form weak collagen hydrogels. While these weak collagen hydrogels have their applications, synthetic polymers are often required to reinforce gel-laden constructs that aim to replicate dense collagenous tissues found in vivo. In this study, aerosol jet printing (AJP) was used to print and process collagen type I and II into dense constructs with a greater capacity to replicate the dense collagenous ECM found in connective tissues. Collagen type I and II was isolated from animal tissues to form solutions for printing. Collagen type I and II constructs were printed with 576 layers and measured to have average effective elastic moduli of 241.3 ± 94.3 and 196.6 ± 86.0 kPa (±SD), respectively, without any chemical modification. Collagen type II solutions were measured to be less viscous than type I and both collagen type I and II exhibited a drop in viscosity due to AJP. Circular dichroism and SDS-PAGE showed collagen type I to be more vulnerable to structural changes due to the stresses of the aerosol formation step of aerosol jet printing while the collagen type II triple helix was largely unaffected. SEM illustrated that distinct layers remained in the aerosol jet print constructs. The results show that aerosol jet printing should be considered an effective way to process collagen type I and II into stiff dense constructs with suitable mechanical properties for the replication of dense collagenous connective tissues.

SUBMITTER: Gibney R

PROVIDER: S-EPMC8602098 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Digitally Driven Aerosol Jet Printing to Enable Customisable Neuronal Guidance.

Project description:Digitally driven manufacturing technologies such as aerosol jet printing (AJP) can make a significant contribution to enabling new capabilities in the field of tissue engineering disease modeling and drug screening. AJP is an emerging non-contact and mask-less printing process which has distinct advantages over other patterning technologies as it offers versatile, high-resolution, direct-write deposition of a variety of materials on planar and non-planar surfaces. This research demonstrates the ability of AJP to print digitally controlled patterns that influence neuronal guidance. These consist of patterned poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) tracks on both glass and poly(potassium 3-sulfopropyl methacrylate) (PKSPMA) coated glass surfaces, promoting selective adhesion of SH-SY5Y neuroblastoma cells. The cell attractive patterns had a maximum height ≥0.2 μm, width and half height ≥15 μm, Ra = 3.5 nm, and RMS = 4.1. The developed biocompatible PEDOT:PSS ink was shown to promote adhesion, growth and differentiation of SH-SY5Y neuronal cells. SH-SY5Y cells cultured directly onto these features exhibited increased nuclei and neuronal alignment on both substrates. In addition, the cell adhesion to the substrate was selective when cultured onto the PKSPMA surfaces resulting in a highly organized neural pattern. This demonstrated the ability to rapidly and flexibly realize intricate and accurate cell patterns by a computer controlled process.

| S-EPMC8435718 | biostudies-literature

Aerosol Jet Printing of 3D Pillar Arrays from Photopolymer Ink.

Project description:An aerosol jet printing (AJP) printing head built on top of precise motion systems can provide positioning deviation down to 3 μm, printing areas as large as 20 cm × 20 cm × 30 cm, and five-axis freedom of movement. Typical uses of AJP are 2D printing on complex or flexible substrates, primarily for applications in printed electronics. Nearly all commercially available AJP inks for 2D printing are designed and optimized to reach desired electronic properties. In this work, we explore AJP for the 3D printing of free-standing pillar arrays. We utilize aryl epoxy photopolymer as ink coupled with a cross-linking "on the fly" technique. Pillar structures 550 μm in height and with a diameter of 50 μm were 3D printed. Pillar structures were characterized via scanning electron microscopy, where the morphology, number of printed layers and side effects of the AJP technique were investigated. Satellite droplets and over-spray seem to be unavoidable for structures smaller than 70 μm. Nevertheless, reactive ion etching (RIE) as a post-processing step can mitigate AJP side effects. AJP-RIE together with photopolymer-based ink can be promising for the 3D printing of microstructures, offering fast and maskless manufacturing without wet chemistry development and heat treatment post-processing.

| S-EPMC9412835 | biostudies-literature

Achieving Selective Wettability Surface through Aerosol Jet Hydrophobic Line Printing.

Project description:Selective wettability surface patterning, involving the combination of wetting and nonwetting surface features in an alternating manner, has emerged as a key surface control technique with broad applications in cell microarrays, microfluidics, and drop placement. However, traditional approaches to creating such patterns often suffer material waste and rely on masking substrate surfaces with predesigned templates, resulting in elevated costs. Here, we present an approach to achieve selective wettability surface patterning using aerosol jet printing that offers a solution to these challenges. Our method involves the precise deposition of atomized, hydrophobic silica nanoparticle droplets onto substrate surfaces. By directing these atomized droplets, we created well-defined hydrophobic lines. The individual lines have an average width of 60 μm and a thickness of 1.32 μm, which, when overlaid, form a complete superhydrophobic surface with a water contact angle of 154°. The implications of these findings are substantial for various applications. We accordingly show the applicability of our method for confining drops and demonstrate on-target waterproofing of electronic circuit lines.

| S-EPMC10851364 | biostudies-literature

Aerosol Jet Printing of Graphene and Carbon Nanotube Patterns on Realistically Rugged Substrates.

Project description:Direct-write additive manufacturing of graphene and carbon nanotube (CNT) patterns by aerosol jet printing (AJP) is promising for the creation of thermal and electrical interconnects in (opto)electronics. In realistic application scenarios, this however often requires deposition of graphene and CNT patterns on rugged substrates such as, for example, roughly machined and surface-oxidized metal block heat sinks. Most AJP of graphene/CNT patterns has thus far however concentrated on flat wafer- or foil-type substrates. Here, we demonstrate AJP of graphene and single walled CNT (SWCNT) patterns on realistically rugged plasma-electrolytic-oxidized (PEO) Al blocks, which are promising heat sink materials. We show that AJP on the rugged substrates offers line resolution of down to ∼40 μm width for single AJP passes, however, at the cost of noncomplete substrate coverage including noncovered μm-sized pores in the PEO Al blocks. With multiple AJP passes, full coverage including coverage of the pores is, however, readily achieved. Comparing archetypical aqueous and organic graphene and SWCNT inks, we show that the choice of the ink system drastically influences the nanocarbon AJP parameter window, deposit microstructure including crystalline quality, compactness of deposit, and inter/intrapass layer adhesion for multiple passes. Simple electrical characterization indicates aqueous graphene inks as the most promising choice for AJP-deposited electrical interconnect applications. Our parameter space screening thereby forms a framework for rational process development for graphene and SWCNT AJP on application-relevant, rugged substrates.

| S-EPMC8697012 | biostudies-literature

Aerosol Jet Printing of SU-8 as a Passivation Layer Against Ionic Solutions.

Project description:To ensure stability for low-cost electronics used in direct contact with ionic solutions (such as electronic biosensors), electrodes are frequently passivated to protect against current leakage, which leads to corrosion. The epoxy-based polymer SU-8 yields favorable properties for passivation against ionic solutions. However, it is nearly universally patterned via cleanroom techniques, which increases device cost and fabrication complexity. Printing electronic components has been shown to be a viable approach for decreasing fabrication cost. Previous reports on SU-8 printing focus on the resultant printed structure, with little emphasis on its subsequent use as a passivation layer. Here, we demonstrate the printing of SU-8 with an aerosol jet printer using ultrasonic aerosolization. We show that SU-8 can be printed without reformulation, and that printed SU-8 is a viable passivation layer over conductive silver lines, when tested in ionic solutions. Extending the printed SU-8 film beyond the underlying conductive electrodes by 100 μm produced a six order of magnitude decrease in leakage current and resulted high stability over 20 voltage sweeps. Finally, we optimized post-printing cure time to 15 minutes at 160°C, which further minimized leakage current. While the development of low-cost, electronic biosensing devices has increasingly moved towards printing methods, the lack of a printed passivation strategy has hindered this transition. The advancements made in this study towards an aerosol jet printable SU-8 passivation layer provide useful progress towards a fully printed, stable electronic biosensing device.

| S-EPMC9387772 | biostudies-literature

Conformal printed electronics on flexible substrates and inflatable catheters using lathe-based aerosol jet printing.

Project description:With the growth of additive manufacturing (AM), there has been increasing demand for fabricating conformal electronics that directly integrate with larger components to enable unique functionality. However, fabrication of conformal electronics is challenging because devices must merge with host substrates regardless of curvilinearity, topography, or substrate material. In this work, we employ aerosol jet (AJ) printing, an AM method for jet printing electronics using ink-based materials, and a custom-made lathe mechanism for mounting flexible substrates and 3D objects on a rotating axis. Using this method of lathe-based AJ printing, conformal electronics are printed around the circumference of rotational bodies with 3D curvilinear surfaces through cylindrical-coordinate motion. We characterize the diverse capabilities of lathe AJ (LAJ) printing and demonstrate flexible conformal electronics including multilayer carbon nanotube transistors. Lastly, a graphene sensor is conformally printed on an inflated catheter balloon for temperature and inflation monitoring, thus highlighting the versatilities of LAJ printing.

| S-EPMC11364510 | biostudies-literature

Aerosol Jet Printing of Silver Lines with A High Aspect Ratio on A Heated Silicon Substrate.

Project description:In this work, we studied the formation of conductive silver lines with high aspect ratios (AR = thickness/width) > 0.1 using the modernized method of aerosol jet printing on a heated silicon substrate. The geometric (AR) and electrical (resistivity) parameters of the formed lines were investigated depending on the number of printing layers (1-10 layers) and the temperature of the substrate (25-300 °C). The AR of the lines increased as the number of printing layers and the temperature of the substrate increased. An increase in the AR of the lines with increasing substrate temperature was associated with a decrease in the ink spreading as a result of an increase in the rate of evaporation of nano-ink. Moreover, with an increase in the substrate temperature of more than 200 °C, a significant increase in the porosity of the formed lines was observed, and as a result, the electrical resistivity of the lines increased significantly. Taking into account the revealed regularities, it was demonstrated that the formation of silver lines with a high AR > 0.1 and a low electrical resistivity of 2-3 ???cm is advisable to be carried out at a substrate temperature of about 100 °C. The adhesion strength of silver films formed on a heated silicon substrate is 2.8 ± 0.9 N/mm2, which further confirms the suitability of the investigated method of aerosol jet printing for electronic applications.

| S-EPMC7040915 | biostudies-literature

Uniform and Stable Aerosol Jet Printing of Carbon Nanotube Thin-Film Transistors by Ink Temperature Control.

Project description:Semiconducting carbon nanotube (CNT) networks exhibit electrical, mechanical, and chemical properties attractive for thin-film applications, and printing allows for scalable and economically favorable fabrication of CNT thin-film transistors (TFTs). However, device-to-device variation of printed CNT-TFTs remains a concern, which largely stems from variations in printed CNT thin-film morphology and resulting properties. In this work, we overcome the challenges associated with printing uniformity and demonstrate an aerosol jet printing process that yields devices exhibiting a hole mobility of μh = 12.5 cm2/V·s with a relative standard deviation as small as 4% (from over 38 devices). The enabling factors of such high uniformity include control of the CNT ink bath temperature during printing, ink formulation with nonvolatile and viscosifying additives, and a thermal treatment for polymer removal. It is discovered that a low CNT ink temperature benefits aerosol jet printing uniformity and stability in both short-term (∼1 min) and long-term (∼1 h) printing settings. These findings shed light on the effect of a commonly overlooked dimension of CNT aerosol jet printing and provide a practical strategy for large-scale, high-consistency realization of CNT-TFTs.

| S-EPMC7895321 | biostudies-literature

Bioprinting of heterogeneous and multilayered cell-hydrogel constructs using continuous multi-material printing and aerosol-based crosslinking.

Project description:Bioprinting is a powerful biofabrication technique that mimics physiological environments and functions. Here, we describe a protocol to set up a continuous multiple-material bioprinting system that can replicate structurally complex and biologically functional microphysiological systems such as a tumor microenvironment. Although this bioprinting system uses a limited crosslinking agent, it is a versatile and advanced continuous multi-material printing technique. For complete details on the use and execution of this protocol, please refer to Lee et al. (2021).

| S-EPMC9038776 | biostudies-literature

Lab-on-Chip, Surface-Enhanced Raman Analysis by Aerosol Jet Printing and Roll-to-Roll Hot Embossing.

Project description:Surface-enhanced Raman spectroscopy (SERS) combines the high speciﬁcity of Raman scattering with high sensitivity due to an enhancement of the electromagnetic ﬁeld by metallic nanostructures. However, the tyical fabrication methods of SERS substrates suffer from low throughput and therefore high costs. Furthermore, point-of-care applications require the investigation of liquid solutions and thus the integration of the SERS substrate in a microfluidic chip. We present a roll-to-roll fabrication approach for microfluidics with integrated, highly efficient, surface-enhanced Raman scattering structures. Microfluidic channels are formed using roll-to-roll hot embossing in polystyrene foil. Aerosol jet printing of a gold nanoparticle ink is utilized to manufacture highly efficient, homogeneous, and reproducible SERS structures. The modified channels are sealed with a solvent-free, roll-to-roll, thermal bonding process. In continuous flow measurements, these chips overcome time-consuming incubation protocols and the poor reproducibility of SERS experiments often caused by inhomogeneous drying of the analyte. In the present study, we explore the influence of the printing process on the homogeneity and the enhancement of the SERS structures. The feasibility of aerosol-jet-modified microfluidic channels for highly sensitive SERS detection is demonstrated by using solutions with different concentrations of Rhodamine 6G and adenosine. The printed areas provide homogeneous enhancement factors of ~4 × 10⁶. Our work shows a way towards the low-cost production of tailor-made, SERS-enabled, label-free, lab-on- chip systems for bioanalysis.

| S-EPMC5677385 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data