Dataset Information

Clinical effects with customized brackets and CAD/CAM technology: a prospective controlled study.

ABSTRACT:

Objective

Nowadays, CAD/CAM technologies enrich orthodontics in several ways. While they are commonly used for diagnoses and treatment planning, they can also be applied to create individualized bracket systems. The purpose of this prospective quasi-randomized study was to evaluate the clinical efficiency of a customized bracket system and its comparison with directly bonded conventional self-ligating bracket treatment.

Materials and methods

Altogether 38 patients were separated into two groups, treated either with direct bonded self-ligating brackets (Damon, Ormco, USA) or with indirect bonded customized CAD/CAM brackets (Insignia™, Ormco, USA). Overall treatment time, number of treatment appointments, number of lost or repositioned brackets, number of arch wires and wire bends, Little Irregularity Index, cephalometric analyses and ABO scores were compared. Superimpositions of the virtual set-ups and the treatment results of the CAD/CAM group were performed to evaluate the clinical realization of the treatment planning.

Results

No differences between both treatment groups were found concerning overall treatment time, number of appointments and number of archwire bends. Bonding failures occurred more often using the CAD/CAM system. Indirectly bonded brackets did not have to be repositioned as often as directly bonded brackets. Treatment results with both systems were similar concerning their effects on the reduction of ABO scores. The number of used archwires was higher in the CAD/CAM group. Treatment with both systems led to further proclination of the incisors. Proclination in the lower jaw was greater than proclination in the upper jaw, and there was a statistically significant difference between the two treatment systems. Comparing the treatment results with the virtual set-ups, mesial positions were met best, followed by vertical positions. Transversal positions showed the greatest discrepancies. Concerning angles, values of angulation showed greatest accordance to the virtual set-up, while values of inclinations showed greatest discrepancies.

Conclusion

In comparison with a direct bonded self-ligating bracket system the use of indirect bonded customized CAD/CAM brackets showed only minor influence on treatment efficiency and treatment outcomes. Transversal expansion, deep bite correction, expression of torque and anchorage loss remain challenges in the treatment with straight-wire appliances. Trial registration DRKS, DRKS00024350. Registered 15 February 2021, https://www.drks.de/drks_web/navigate.do?navigationId=trial.HTML&TRIAL_ID=DRKS00024350 .

SUBMITTER: Hegele J

PROVIDER: S-EPMC8645527 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:The augmentation of the jaw has been and continues to be a sophisticated therapy in implantology. Modern CAD-CAM technologies lead to revival of old and established augmentation techniques such as the use of titanium mesh (TM) for bone augmentation. The aim of this retrospective study was to evaluate the clinical outcome of an individualized CAD-CAM-produced TM based on the CT/DVT-DICOM data of the patients for the first time.In 17 patients, 21 different regions were augmented with an individualized CAD-CAM-produced TM (Yxoss CBR®, Filderstadt, Germany). For the augmentation, a mixture of autologous bone and deproteinized bovine bone mineral (DBBM) or autologous bone alone was used. Reentry with explantation of the TM and simultaneous implantation of 44 implants were performed after 6 months. Preoperative and 6-month postoperative cone beam computed tomographies (CBCT) were performed to measure the gained bone height.The success rate for the bone grafting procedure was 100%. Thirty-three percent of cases presented an exposure of the TM during the healing period. However, premature removal of these exposed meshes was not necessary. Exposure rate in augmentations performed with mid-crestal incisions was higher than in augmentations performed with a modified poncho incision (45.5 vs. 20%, p = 0.221). In addition, exposure rates in the maxilla were significantly higher than in the mandible (66.7 vs. 8.3%, p = 0.009). Gender, smoking, periodontal disease, gingiva type, used augmentation material, and used membrane had no significant influence on the exposure rate (p > 0.05). The mean vertical augmentation was 6.5 ± 1.7 mm, and the mean horizontal augmentation was 5.5 ± 1.9 mm. Implant survival rate after a mean follow-up of 12 ± 6 months after reentry was 100%.Within the limits of the retrospective character of this study, this study shows for the first time that individualized CAD-CAM TM provide a sufficient and safe augmentation technique, especially for vertical and combined defects. However, the soft tissue handling for sufficient mesh covering remains one of the most critical steps using this technique.

Project description:BACKGROUND:Recent studies showed that finite element model (FEM) combined to CAD/CAM improves the design of braces for the conservative treatment of adolescent idiopathic scoliosis (AIS), using 2D measurements from in-brace radiographs. We aim to assess the immediate effectiveness on curve correction in all three planes of braces designed using CAD/CAM and numerical simulation compared to braces designed with CAD/CAM only. METHODS:SRS standardized criteria for bracing were followed to recruit 48 AIS patients who were randomized into two groups. For both groups, 3D reconstructions of the spine and patient's torso, respectively built from bi-planar radiographs and surface topography, were obtained and braces were designed using the CAD/CAM approach. For the test group, 3D reconstructions of the spine and patient's torso were additionally used to generate a personalized FEM to simulate and iteratively improve the brace design with the objective of curve correction maximization in three planes and brace material minimization. RESULTS:For the control group (CtrlBraces), average Cobb angle prior to bracing was 29° (thoracic, T) and 25° (lumbar, L) with the planes of maximal curvature (PMC) respectively oriented at 63° and 57° on average with respect to the sagittal plane. Average apical axial rotation prior to bracing was 7° (T) and 9° (L). For the test group (FEMBraces), initial Cobb angles were 33° (T) and 28° (L) with the PMC at 68° (T) and 56° (L) and average apical axial rotation prior to bracing at 9° (T and L). On average, FEMBraces were 50% thinner and had 20% less covering surface than CtrlBraces while reducing T and L curves by 47 and 48%, respectively, compared to 25 and 26% for CtrlBraces. FEMBraces corrected apical axial rotation by 46% compared to 30% for CtrlBraces. CONCLUSION:The combination of numerical simulation and CAD/CAM approach allowed designing more efficient braces in all three planes, with the advantages of being lighter than standard CAD/CAM braces. Bracing in AIS may be improved in 3D by the use of this simulation platform. This study is ongoing to recruit more cases and to analyze the long-term effect of bracing. TRIAL REGISTRATION:ClinicalTrials.gov, NCT02285621.