Melt-Extrusion-Based Additive Manufacturing of Transparent Fused Silica Glass.
Ontology highlight
ABSTRACT:
SUBMITTER: Mader M
PROVIDER: S-EPMC8655167 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Fused silica glass is the preferred material for applications which require long-term chemical and mechanical stability as well as excellent optical properties. The manufacturing of complex hollow microstructures within transparent fused silica glass is of particular interest for, among others, the miniaturization of chemical synthesis towards more versatile, configurable and environmentally friendly flow-through chemistry as well as high-quality optical waveguides or capillaries. However, microstructuring of such complex three-dimensional structures in glass has proven evasive due to its high thermal and chemical stability as well as mechanical hardness. Here we present an approach for the generation of hollow microstructures in fused silica glass with high precision and freedom of three-dimensional designs. The process combines the concept of sacrificial template replication with a room-temperature molding process for fused silica glass. The fabricated glass chips are versatile tools for, among other, the advance of miniaturization in chemical synthesis on chip.
| S-EPMC6441035 | biostudies-literature
Project description:Additive manufacturing is widely used to produce highly complex structures. Moreover, this technology has proven its superiority in producing tools which can be used in different applications. We designed and produced an extrusion nozzle that allowed us to hot melt extrude drug-loaded tubes. The tubes were an essential part of a new mouse ventilator-associated pneumonia (VAP) model. Ciprofloxacin (CPX) was selected for its expected activity against the pathogen Staphylococcus aureus and ease of incorporation into thermoplastic polyurethane (TPU). TPU was selected as the carrier polymer for its biocompatibility and use in a variety of medical devices such as tubing and catheters. The effect of loading CPX within the TPU polymeric matrix and the physicochemical properties of the produced tubes were investigated. CPX showed good thermal stability and in vitro activity in preventing S. aureus biofilm formation after loading within the tube's polymeric matrix. Moreover, the produced tubes showed anti-infective efficacy in vivo. The produced tubes, which were extruded via our novel nozzle, were vital for the validation of our mouse VAP model. This model can be adopted to investigate other antibacterial and antibiofilm compounds incorporated in polymeric tubes using hot melt extrusion.
| S-EPMC8224298 | biostudies-literature
Project description:Material extrusion (ME) is a layer-by-layer additive manufacturing process that is now used in personal and commercial production where prototyping and customization are required. However, parts produced from ME frequently exhibit poor mechanical performance relative to those from traditional means; moreover, fundamental knowledge of the factors leading to development of inter-layer strength in this highly non-isothermal process is limited. In this work, we seek to understand the development of inter-layer weld strength from the perspective of polymer interdiffusion under conditions of rapidly changing mobility. Our framework centers around three interrelated components: in situ thermal measurements (via infrared imaging), temperature dependent molecular processes (via rheology), and mechanical testing (via mode III fracture). We develop the concept of an equivalent isothermal weld time and test its relationship to fracture energy. For the printing conditions studied the equivalent isothermal weld time for Tref = 230 °C ranged from 0.1 ms to 100 ms. The results of these analysis provide a basis for optimizing inter-layer strength, the limitations of the ME process, and guide development of new materials.
| S-EPMC5684701 | biostudies-other
Project description:The present work explored the use of the selective laser melting (SLM) technique to develop a Zr-based bulk metallic glass (BMG) and investigate the influence of the process parameters on obtaining different levels of surface roughness. Moreover, the potential of the additively manufactured BMG Zr59.3Cu28.8Al10.4Nb1.5 (trade name AMLOY-ZR01) as an implant material was studied by evaluating the osteoblastic cell response to the alloy and its stability under simulated biological environments. The materials were characterized in terms of degree of crystallinity, surface roughness, and morphology, followed by a systematic investigation of the response of the MC3T3-E1 preosteoblastic cell line to the as-printed samples. The materials supported cell proliferation and differentiation of the preosteoblastic cells, with results comparable to the reference material Ti-6Al-4V. The surface microroughness and surface morphology (porous or groove-type laser tracks) investigated in this study did not have a significant effect on modulating the cell response. Ion release experiments showed a large increase in ion release under inflammatory conditions as compared to regular physiological conditions, which could be attributed to the increased local corrosion under inflammatory conditions. The findings in this work showed that the surface roughness of the additively manufactured BMG AMLOY-ZR01 can be tailored by controlling the laser power applied during the SLM process. The favorable cell response to the as-printed AMLOY-ZR01 represents of a significant advancement of the investigation of additively manufactured BMGs for orthopedic applications, while the results of the ion release study highlights the effect that inflammatory conditions could have on the degradation of the alloy.
| S-EPMC9768811 | biostudies-literature
Project description:Fabrication of glass with complex geocd the low resolution of particle-based or fused glass technologies. Herein, a high-resolution 3D printing of transparent nanoporous glass is presented, by the combination of transparent photo-curable sol-gel printing compositions and digital light processing (DLP) technology. Multi-component glass, including binary (Al2 O3 -SiO2 ), ternary (ZnO-Al2 O3 -SiO2 , TiO2 -Al2 O3 -SiO2 ), and quaternary oxide (CaO-P2 O5 -Al2 O3 -SiO2 ) nanoporous glass objects with complex shapes, high spatial resolutions, and multi-oxide chemical compositions are fabricated, by DLP printing and subsequent sintering process. The uniform nanopores of Al2 O3 -SiO2 -based nanoporous glasses with the diameter (≈6.04 nm), which is much smaller than the visible light wavelength, result in high transmittance (>95%) at the visible range. The high surface area of printed glass objectives allows post-functionalization via the adsorption of functional guest molecules. The photoluminescence and hydrophobic modification of 3D printed glass objectives are successfully demonstrated. This work extends the scope of 3D printing to transparent nanoporous glasses with complex geometry and facile functionalization, making them available for a wide range of applications.
| S-EPMC10724418 | biostudies-literature
Project description:Past work has shown that particle material extrusion (fused particle fabrication (FPF)/fused granular fabrication (FGF)) has the potential for increasing the use of recycled polymers in 3D printing. This study extends this potential to high-performance (high-mechanical-strength and heat-resistant) polymers using polycarbonate (PC). Recycled PC regrind of approximately 25 mm2 was 3D printed with an open-source Gigabot X and analyzed. A temperature and nozzle velocity matrix was used to find useful printing parameters, and a print test was used to maximize the output for a two-temperature stage extruder for PC. ASTM type 4 tensile test geometries as well as ASTM-approved compression tests were used to determine the mechanical properties of PC and were compared with filament printing and the bulk virgin material. The results showed the tensile strength of parts manufactured from the recycled PC particles (64.9 MPa) were comparable to that of the commercial filament printed on desktop (62.2 MPa) and large-format (66.3 MPa) 3D printers. Three case study applications were investigated: (i) using PC as a rapid molding technology for lower melting point thermoplastics, (ii) printed parts for high temperature applications, and (iii) printed parts for high-strength applications. The results show that recycled PC particle-based 3D printing can produce high-strength and heat-resistant products at low costs.
| S-EPMC6566670 | biostudies-literature
Project description:Extrusion-based additive manufacturing (EBAM) or 3D printing is used to produce customized prototyped parts. The majority of the polymers used with EBAM show moisture sensitivity. However, moisture effects become more pronounced in polymers used for critical applications, such as biomedical stents, sensors, and actuators. The effects of moisture on the manufacturing process and the long-term performance of Shape Memory Polyurethane (SMPU) have not been fully investigated in the literature. This study focuses primarily on block-copolymer SMPUs that have two different hard/soft (h/s) segment ratios. It investigates the effect of moisture on the various properties via studying: (i) the effect of moisture trapping within these polymers and the consequences when manufacturing; (ii) and the effect on end product performance of plasticization by moisture. Results indicate that higher h/s SMPU shows higher microphase separation, which leads to an increase of moisture trapping within the polymer. Understanding moisture trapping is critical for EBAM parts due to an increase in void content and a decrease in printing quality. The results also indicate a stronger plasticizing effect on polymers with lower h/s ratio but with a more forgiving printing behavior compared to the higher h/s ratio.
| S-EPMC6356422 | biostudies-literature
Project description:Extrusion-based printing enables simplified and economic manufacturing of surgical guides for oral implant placement. Therefore, the cytotoxicity of a biocopolyester (BE) and a polypropylene (PP), intended for the fused filament fabrication of surgical guides was evaluated. For comparison, a medically certified resin based on methacrylic esters (ME) was printed by stereolithography (n = 18 each group). Human gingival keratinocytes (HGK) were exposed to eluates of the tested materials and an impedance measurement and a tetrazolium assay (MTT) were performed. Modulations in gene expression were analyzed by quantitative PCR. One-way ANOVA with post-hoc Tukey tests were applied. None of the materials exceeded the threshold for cytotoxicity (< 70% viability in MTT) according to ISO 10993-5:2009. The impedance-based cell indices for PP and BE, reflecting cell proliferation, showed little deviations from the control, while ME caused a reduction of up to 45% after 72 h. PCR analysis after 72 h revealed only marginal modulations caused by BE while PP induced a down-regulation of genes encoding for inflammation and apoptosis (p < 0.05). In contrast, the 72 h ME eluate caused an up-regulation of these genes (p < 0.01). All evaluated materials can be considered biocompatible in vitro for short-term application. However, long-term contact to ME might induce (pro-)apoptotic/(pro-)inflammatory responses in HGK.
| S-EPMC9072356 | biostudies-literature
Project description:BackgroundRecent efforts in fungal biotechnology aim to develop new concepts and technologies that convert renewable plant biomass into innovative biomaterials. Hereby, plant substrates become metabolized by filamentous fungi to transform them into new fungal-based materials. Current research is thus focused on both understanding and optimizing the biology and genetics underlying filamentous fungal growth and on the development of new technologies to produce customized fungal-based materials.ResultsThis manuscript reports the production of stable pastes, composed of Fomes fomentarius mycelium, alginate and water with 71 wt.% mycelium in the solid content, for additive manufacturing of fungal-based composite materials. After printing complex shapes, such as hollow stars with up to 39 mm in height, a combination of freeze-drying and calcium-crosslinking processes allowed the printed shapes to remain stable even in the presence of water. The printed objects show low bulk densities of 0.12 ± 0.01 g/cm3 with interconnected macropores.ConclusionsThis work reports for the first time the application of mycelium obtained from the tinder fungus F. fomentarius for an extrusion-based additive manufacturing approach to fabricate customized light-weight 3D objects. The process holds great promise for developing light-weight, stable, and porous fungal-based materials that could replace expanded polystyrene produced from fossil resources.
| S-EPMC8693477 | biostudies-literature
Project description:Many types of consumer-grade packaging can be used in material extrusion additive manufacturing processes, providing a high-value output for waste plastics. However, many of these plastics have reduced mechanical properties and increased warpage/shrinkage compared to those commonly used in three-dimensional (3D) printing. The addition of reinforcing materials can lead to stiffer parts with reduced distortion. This paper presents work in the reinforcement of recycled polypropylene using cellulose waste materials to generate a green composite feedstock for extrusion-based polymer additive manufacturing. Recycled polypropylene/waste paper, cardboard, and wood flour composites were made using a solid-state shear pulverization process. Fourier transform infrared and thermogravimetric analysis were utilized to qualitatively analyze the amount of filler incorporated into the 3D-printed materials. Recycled polymer composites had increased levels of filler incorporated in the printed parts compared to the virgin polymer composites based on the thermal gravimetric analysis. The dynamic mechanical analysis showed a ca. 20-30% increase in storage modulus with the addition of cellulose materials. Tensile strength was not significantly increased with the addition of 10 wt % cellulose, but the elastic modulus increased 38% in virgin polypropylene. The analysis of fracture surfaces revealed that failure initiates at the interface, suggesting that the interfacial strength is weaker than the filler strength.
| S-EPMC6713991 | biostudies-literature