Browse
Submit Data
Databases
API
Help

Dataset Information

34 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Effects of He and Ar Heat-Assisted Plasma Treatments on the Adhesion Properties of Polytetrafluoroethylene (PTFE).

ABSTRACT: Heat-assisted plasma (HAP) treatment using He gas is known to improve the adhesive-bonding and adhesive-free adhesion properties of polytetrafluoroethylene (PTFE). In this study, we investigated the effects of He and Ar gaseous species on the HAP-treated PTFE surface. Epoxy (EP) adhesive-coated stainless steel (SUS304) and isobutylene-isoprene rubber (IIR) were used as adherents for the evaluation of the adhesive-bonding and adhesive-free adhesion properties of PTFE. In the case of adhesive bonding, the PTFE/EP-adhesive/SUS304 adhesion strength of the Ar-HAP-treated PTFE was the same as that of the He-HAP-treated PTFE. In the case of adhesive-free adhesion, the PTFE/IIR adhesion strength of the Ar-HAP-treated PTFE was seven times lower than that of the He-HAP-treated PTFE. The relation among gaseous species used in HAP treatment, adhesion properties, peroxy radical density ratio, surface chemical composition, surface modification depth, surface morphology, surface hardness, and the effect of irradiation with vacuum ultraviolet (VUV) and UV photons were investigated. The different adhesive-free adhesion properties obtained by the two treatments resulted from the changes in surface chemical composition, especially the ratios of oxygen-containing functional groups and C-C crosslinks.

SUBMITTER: Ohkubo Y

PROVIDER: S-EPMC8659427 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Drastic Improvement in Adhesion Property of Polytetrafluoroethylene (PTFE) via Heat-Assisted Plasma Treatment Using a Heater.

Project description:The heating effect on the adhesion property of plasma-treated polytetrafluoroethylene (PTFE) was examined. For this purpose, a PTFE sheet was plasma-treated at atmospheric pressure while heating using a halogen heater. When plasma-treated at 8.3?W/cm2 without using the heater (Low-P), the surface temperature of Low-P was about 95?°C. In contrast, when plasma-treated at 8.3?W/cm2 while using the heater (Low-P+Heater), the surface temperature of Low-P+Heater was controlled to about 260?°C. Thermal compression of the plasma-treated PTFE with or without heating and isobutylene-isoprene rubber (IIR) was performed, and the adhesion strength of the IIR/PTFE assembly was measured via the T-peel test. The adhesion strengths of Low-P and Low-P+Heater were 0.12 and 2.3?N/mm, respectively. Cohesion failure of IIR occurred during the T-peel test because of its extremely high adhesion property. The surfaces of the plasma-treated PTFE with or without heating were investigated by the measurements of electron spin resonance, X-ray photoelectron spectroscopy, nanoindentation, scanning electron microscopy, and scanning probe microscopy. These results indicated that heating during plasma treatment promotes the etching of the weak boundary layer (WBL) of PTFE, resulting in a sharp increase in the adhesion property of PTFE.

| S-EPMC5573392 | biostudies-literature

Adhesive-Free Adhesion between Plasma-Treated Glass-Cloth-Containing Polytetrafluoroethylene (GC-PTFE) and Stainless Steel: Comparison between GC-PTFE and Pure PTFE.

Project description:In this study, the effect of plasma treatment on glass-cloth-containing polytetrafluoroethylene (GC-PTFE) was investigated. Previous plasma studies investigated pure PTFE (which does not contain glass cloth) but not GC-PTFE. The effect of Ar + H2O plasma treatment on GC-PTFE was investigated. The Ar + H2O plasma-treated GC-PTFE sheets were thermally compressed to stainless steel (SUS304) foils without using adhesive, and the GC-PTFE/SUS304 adhesion strengths were measured using a 90° peel test. The adhesion strength increased with the increase in the plasma treatment time (0.8 and 1.0 N/mm at 20 s and 300 s, respectively). Thus, strong adhesion between GC-PTFE/SUS304 was achieved without adhesive. This improvement in the adhesion properties of GC-PTFE can be attributed to the generation of oxygen-containing functional groups and the decrease in the surface roughness of the samples. Thereafter, the adhesion properties of GC-PTFE and pure PTFE were compared. Because, unlike pure PTFE, GC-PTFE has no weak boundary layer, GC-PTFE exhibited better adhesion properties than pure PTFE under short plasma treatment times.

| S-EPMC8838903 | biostudies-literature

Adhesive-free adhesion between heat-assisted plasma-treated fluoropolymers (PTFE, PFA) and plasma-jet-treated polydimethylsiloxane (PDMS) and its application.

Project description:Conventional low-temperature plasma treatment was reported to minimally improve the adhesion property of polytetrafluoroethylene (PTFE), whereas heat-assisted plasma (HAP) treatment significantly improved the same. An unvulcanized rubber was previously used as an adherent for PTFE. This study aimed to achieve strong adhesive-free adhesion between PTFE and vulcanized polydimethylsiloxane (PDMS) rubber. As-received vulcanized PDMS rubber did not adhere to HAP-treated PTFE, and as-received PTFE did not adhere to vulcanized rubber of plasma-jet (PJ) treated PDMS rubber; however, HAP-treated PTFE strongly adhered to vulcanized PJ-treated PDMS rubber, and both PTFE and PDMS exhibited cohesion failure in the T-peel test. The surface chemical compositions of the PTFE and PDMS sides were determined using X-ray photoelectron spectroscopy. The strong PTFE/PDMS adhesion was explained via hydrogen and covalent bond formation (C-O-Si and/or C(=O)-O-Si) between hydroxyl (C-OH) or carboxyl (C(=O)-OH) groups of the HAP-treated PTFE. This process was also applied to adhesive-free adhesion between a tetrafluoroethylene-perfluoroalkylvinylether copolymer (PFA) and PDMS; subsequently, a translucent PFA/PDMS assembly with strong adhesion was realized together with the PTFE/PDMS assembly. Strong adhesive-free adhesion between fluoropolymers (PTFE, PFA) and vulcanized PDMS rubber without using any adhesives and graft polymer was successfully realized upon plasma treatment of both the fluoropolymer and PDMS sides. Additionally, a PDMS sheet, which was PJ-treated on both sides, was applied to strongly adhere fluoropolymers (PTFE, PFA) to materials such as metal and glass. PJ-treated PDMS was used as an intermediate layer rather than a strong adhesive, achieving PTFE/PDMS/metal and PTFE/PDMS/glass assemblies. The PTFE/PDMS, PDMS/metal, and PDMS/glass adhesion strengths exceeded 2?N/mm.

| S-EPMC6305381 | biostudies-literature

Low-Pressure H2, NH3 Microwave Plasma Treatment of Polytetrafluoroethylene (PTFE) Powders: Chemical, Thermal and Wettability Analysis

Project description:Functionalization of Polytetrafluoroethylene (PTFE) powders of ~6 ?m particle size is carried out using low-pressure 2.45 GHz H2, NH3 microwave plasmas for various durations (2.5, 10 h) to chemically modify their surface and alter their surface energy. The X-ray Photoelectron Spectroscopy (XPS) analyses reveal that plasma treatment leads to significant defluorination (F/C atomic ratio of 1.13 and 1.30 for 10 h NH3 and H2 plasma treatments, respectively vs. 1.86 for pristine PTFE), along with the incorporation of functional polar moieties on the surface, resulting in enhanced wettability. Analysis of temperature dependent XPS revealed a loss of surface moieties above 200 °C, however, the functional groups are not completely removable even at higher temperatures (>300 °C), thus enabling the use of plasma treated PTFE powders as potential tribological fillers in high temperature engineering polymers. Ageing studies carried over a period of 12 months revealed that while the surface changes degenerate over time, again, they are not completely reversible. These functionalised PTFE powders can be further used for applications into smart, high performance materials such as tribological fillers for engineering polymers and bio-medical, bio-material applications.

| S-EPMC5455540 | biostudies-literature

Tribological and Mechanical Behavior of Graphite Composites of Polytetrafluoroethylene (PTFE) Irradiated by the Electron Beam.

Project description:This research investigated the effect of irradiation with an electron beam energy of 10 MeV in doses of 26-156 kGy on polytetrafluoroethylene (PTFE) with a 15% and 20% graphite additive. The research has shown that mechanical (compression strength, hardness, and Young's modulus) and sclerometric (coefficient of wear micromechanism and coefficient of resistance to wear) properties improve and tribological wear decreases as graphite content increases. Electron beam irradiation increases the degree of crystallinity of both materials to a similar extent. However significant differences in the improvement of all examined properties have been demonstrated for PTFE with higher (20%) graphite content subjected to the electron beam irradiation. This polymer is characterized by higher hardness and Young's modulus, reduced susceptibility to permanent deformation, higher elasticity, compression strength, and above all, a nearly 30% reduction in tribological wear compared to PTFE with a 15% graphite additive. The most advantageous properties can be obtained for both of the examined composites after absorbing a dose of 104 kGy. The obtained results hold promise for the improvement of the operational life of friction couples which do not require lubrication, used for example in air compressors and engines, and for the possibility of application of these modified polymers. In particular PTFE with 20% graphite content, in the nuclear and space industry.

| S-EPMC7464070 | biostudies-literature

Promoting Endothelial Cell Affinity and Antithrombogenicity of Polytetrafluoroethylene (PTFE) by Mussel-Inspired Modification and RGD/Heparin Grafting.

Project description:When used as small-diameter vascular grafts (SDVGs), synthetic biomedical materials like polytetrafluoroethylene (PTFE) may induce thrombosis and intimal hyperplasia due to the lack of an endothelial cell layer. Modification of the PTFE in an aqueous solution is difficult because of its hydrophobicity. Herein, aiming to simultaneously promote endothelial cell affinity and antithrombogenicity, a mussel-inspired modification approach was employed to enable the grafting of various bioactive molecules like RGD and heparin. This approach involves a series of pragmatic steps including oxygen plasma treatment, dopamine (DA) coating, polyethylenimine (PEI) grafting, and RGD or RGD/heparin immobilization. Successful modification in each step was verified via Fourier transform infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). Plasma treatment increased the hydrophilicity of PTFE, thereby allowing it to be efficiently coated with dopamine. Grafting of dopamine, RGD, and heparin led to an increase in surface roughness and a decrease in water contact angle due to increased surface energy. Platelet adhesion increased after dopamine and RGD modification, but it dramatically decreased when heparin was introduced. All of these modifications, especially the incorporation of RGD, showed favorable effects on endothelial cell attachment, viability, and proliferation. Due to strong cell-substrate interactions between endothelial cells and RGD, the RGD/heparin-grafted PTFE demonstrated high endothelial cell affinity. This facile modification method is highly suitable for all hydrophobic surfaces and provides a promising technique for SDVG modification to stimulate fast endothelialization and effective antithrombosis.

| S-EPMC6238965 | biostudies-literature

Effects of heat, anoxia, and combined heat-anoxia treatments

Project description:Anoxia induces several heat shock proteins and a heat pre-treatment can acclimatize Arabidopsis seedlings to a subsequent anoxic treatment. In this work we analyzed the response of Arabidopsis seedlings to anoxia, heat and a combined heat+anoxia stress. A significant overlapping between the anoxic and heat shock responses has been observed by whole-genome microarray analysis.

2009-05-30 | GSE16222 | GEO

Defluorination of Polytetrafluoroethylene Surface by Hydrogen Plasma.

Project description:Defluorination of polytetrafluoroethylene (PTFE) surface film is a suitable technique for tailoring its surface properties. The influence of discharge parameters on the surface chemistry was investigated systematically using radio-frequency inductively coupled H2 plasma sustained in the E- and H-modes at various powers, pressures and treatment times. The surface finish was probed by X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). The measurements of water contact angles (WCA) showed increased wettability of the pristine PTFE; however, they did not reveal remarkable modification in the surface chemistry of the samples treated at various discharge parameters. By contrast, the combination of XPS and ToF-SIMS, however, revealed important differences in the surface chemistry between the E- and H-modes. A well-expressed minimum in the fluorine to carbon ratio F/C as low as 0.2 was observed at the treatment time as short as 1 s when plasma was in the H-mode. More gradual surface chemistry was observed when plasma was in the E-mode, and the minimal achievable F/C ratio was about 0.6. The results were explained by the synergistic effects of hydrogen atoms and vacuum ultraviolet radiation.

| S-EPMC7760809 | biostudies-literature

Study of Radio Frequency Plasma Treatment of PVDF Film Using Ar, O₂ and (Ar + O₂) Gases for Improved Polypyrrole Adhesion.

Project description:Improvement of the binding of polypyrrole with PVDF (polyvinylidene fluoride) thin film using low pressure plasma was studied. The effects of various plasma gases i.e., Ar, O₂ and Ar + O₂ gases on surface roughness, surface chemistry and hydrophilicity were noted. The topographical change of the PVDF film was observed by means of scanning electron microscopy and chemical changes by X-ray photoelectron spectroscopy, with adhesion of polypyrrole (PPy) by abrasion tests and sheet resistance measurements. Results showed that the increase in roughness and surface functionalization by oxygen functional groups contributed to improved adhesion and Ar + O₂ plasma gave better adhesion.

| S-EPMC5521317 | biostudies-other

Wettability of polytetrafluoroethylene surfaces by plasma etching modifications.

Project description:Superhydrophobic surfaces (SHS) are attracting attention in many fields owing to their excellent advantages such as anti-freezing, corrosion prevention, and self-cleaning. However, to modify the surface structure, environmental pollution caused by complex processes and chemical treatment must be considered. In this study, the surface of polytetrafluoroethylene (PTFE) was plasma-treated using oxygen and argon plasma to change the surface structure without a complicated process. The PTFE surface was treated in two ways: plasma etching (PE) and reactive ion etching (RIE). The contact angle of the conventional PTFE surface was 113.8 ± 1.4°, but the contact angle of the manufactured surface was 152.3 ± 1.7° and 172.5 ± 1.2°. The chemical composition and physical structure of the samples produced were compared. The treated specimens had the same chemical composition as the specimen before treatment and exhibited differences in their surface structures. Therefore, it was determined that the change in the water repellency was due to the surface structure. After PE treatment, the specimen surface had a mountain range-like structure, and the RIE specimen had a more detailed structure than the PE specimen. The contact rate of water droplets decreased due to the difference in the structure of the specimen before and after treatment, and the increase in the surface contact angle was manifested. In order to confirm that the plasma treatment reduces surface energy, the shape of the liquid collision was observed using a high-speed camera, and the contact time was calculated to confirm water repellency. The contact time of the PE and RIE specimen was 24 milli-second (ms) and 18 ms, respectively. The high contact angle and low sliding angle of the RIE specimen made it easy to restore surface cleanliness in a self-cleaning experiment using graphite.

| S-EPMC10065265 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data