Progress and prospects of reversible solid oxide fuel cell materials.
Ontology highlight
ABSTRACT:
SUBMITTER: Shen M
PROVIDER: S-EPMC8661483 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Ammonia is a promising carbon-free hydrogen carrier. Owing to their nickel-rich anodes and high operating temperatures, solid oxide fuel cells (SOFCs) can directly utilize NH3 fuel-direct-ammonia SOFCs (DA-SOFCs). Lowering the operating temperature can diversify application areas of DA-SOFCs. We tested direct-ammonia operation using two types of thin-film SOFCs (TF-SOFCs) under 500 to 650°C and compared these with a conventional SOFC. The TF-SOFC with a nickel oxide gadolinium-doped ceria anode achieved a peak power density of 1330 mW cm-2 (NH3 fuel under 650°C), which is the best performance reported to date. However, the performance difference between the NH3 and H2 operations was significant. Electrochemical impedance analyses, ammonia conversion quantification, and two-dimensional multi-physics modeling suggested that reduced ammonia conversion at low temperatures is the main cause of the performance gap. A comparative study with previously reported DA-SOFCs clarified that incorporating a more active ammonia decomposition catalyst will further improve low-temperature DA-SOFCs.
| S-EPMC9464968 | biostudies-literature
Project description:Two perovskite materials with SrMo1-xAlxO3-δ (x = 0.1, 0.2) compositions have been synthesized by reduction from the corresponding scheelite phases, with SrMo1-xAlxO4-δ stoichiometry; the pertinent characterization shows that the defective perovskites can be used as anode materials in solid oxide fuel cells, providing maximum output power densities of 633 mW/cm2 for x = 0.2. To correlate structure and properties, a neutron powder diffraction investigation was carried out for both perovskite and scheelite phases. Both perovskites are cubic, defined in the Pm-3m space group, displaying a random distribution of Mo and Al cations over the 1a sites of the structure. The introduction of Al at Mo positions produced conspicuous amounts of oxygen vacancies in the perovskite, detected by neutrons. This is essential to induce ionic diffusion, providing a mixed ionic and electronic conduction (MIEC), since in MIEC electrodes, charge carriers are combined in one single phase and the ionic conductivity can be one order of magnitude higher than in a conventional material. The thermal expansion coefficients of the reduced and oxidized samples demonstrated that these materials perfectly match with the La0.8Sr0.2Ga0.83Mg0.17O3-δ electrolyte, La0.4Ce0.6O2-δ buffer layer and other components of the cell. Scanning electron microscopy after the test in a real solid oxide fuel cell showed a very dense electrolyte and porous electrodes, essential requirements for this type of fuel. SrMo1-xAlxO3-δ perovskites are, thus, a good replacement of conventional biphasic cermet anodes in solid oxide fuel cells.
| S-EPMC9181521 | biostudies-literature
Project description:SrMo1-xMxO3-δ (M = Fe and Cr, x = 0.1 and 0.2) oxides have been recently described as excellent anode materials for solid oxide fuel cells at intermediate temperatures (IT-SOFC) with LSGM as the electrolyte. In this work, we have improved their properties by doping with aliovalent Mg ions at the B-site of the parent SrMoO₃ perovskite. SrMo1-xMgxO3-δ (x = 0.1, 0.2) oxides have been prepared, characterized and tested as anode materials in single solid-oxide fuel cells, yielding output powers near 900 mW/cm-2 at 850 °C using pure H₂ as fuel. We have studied its crystal structure with an "in situ" neutron power diffraction (NPD) experiment at temperatures as high as 800 °C, emulating the working conditions of an SOFC. Adequately high oxygen deficiencies, observed by NPD, together with elevated disk-shaped anisotropic displacement factors suggest a high ionic conductivity at the working temperatures. Furthermore, thermal expansion measurements, chemical compatibility with the LSGM electrolyte, electronic conductivity and reversibility upon cycling in oxidizing-reducing atmospheres have been carried out to find out the correlation between the excellent performance as an anode and the structural features.
| S-EPMC5456869 | biostudies-other
Project description:Nowadays, the temperature gradient is considered as one of the most important parameters which impact the performance of the solid oxide fuel cell (SOFC). In this paper, a control strategy based on an input-output feedback linearization technology is derived for controlling the maximum temperature gradient within the anode fuel flow channel at the desired value. For the controller design, the temperature dynamic model is proposed and simplified to a control-oriented multi-input and multioutput nonlinear dynamic model. Then, this paper presents an input-output feedback linearization controller to realize the control objective by adjusting the cathode input air flow. Finally, the simulation results are given to demonstrate the accuracy of the proposed model in reflecting the temperature dynamic characteristics. Moreover, the compound controller is added for simulation as a comparison, which shows that the proposed controller is equipped with better effectiveness and efficiency in the presence of external disturbances.
| S-EPMC8552236 | biostudies-literature
Project description:A cobalt-based thermoelectric compound Ca(3)Co(2)O(6) (CCO) has been developed as new cathode material with superior performance for intermediate-temperature (IT) solid-oxide fuel cell (SOFC). Systematic evaluation has been carried out. Measurement of thermal expansion coefficient (TEC), thermal-stress (?) and interfacial shearing stress (?) with the electrolyte show that CCO matches well with several commonly-used IT electrolytes. Maximum power density as high as 1.47 W cm(-2) is attained at 800°C, and an additional thermoelectric voltage of 11.7 mV is detected. The superior electrochemical performance, thermoelectric effect, and comparable thermal and mechanical behaviors with the electrolytes make CCO to be a promising cathode material for SOFC.
| S-EPMC3553459 | biostudies-literature
Project description:Correlating the microstructure of an energy conversion device to its performance is often a complex exercise, notably in solid oxide fuel cell research. Solid oxide fuel cells combine multiple materials and interfaces that evolve in time due to high operating temperatures and reactive atmospheres. We demonstrate here that operando environmental transmission electron microscopy can identify structure-property links in such devices. By contacting a cathode-electrolyte-anode cell to a heating and biasing microelectromechanical system in a single-chamber configuration, a direct correlation is found between the environmental conditions (oxygen and hydrogen partial pressures, temperature), the cell open circuit voltage, and the microstructural evolution of the fuel cell, down to the atomic scale. The results shed important insights into the impact of the anode oxidation state and its morphology on the cell electrical properties.
| S-EPMC10693604 | biostudies-literature
Project description:Accelerating materials research by integrating automation with artificial intelligence is increasingly recognized as a grand scientific challenge to discover and develop materials for emerging and future technologies. While the solid state materials science community has demonstrated a broad range of high throughput methods and effectively leveraged computational techniques to accelerate individual research tasks, revolutionary acceleration of materials discovery has yet to be fully realized. This perspective review presents a framework and ontology to outline a materials experiment lifecycle and visualize materials discovery workflows, providing a context for mapping the realized levels of automation and the next generation of autonomous loops in terms of scientific and automation complexity. Expanding autonomous loops to encompass larger portions of complex workflows will require integration of a range of experimental techniques as well as automation of expert decisions, including subtle reasoning about data quality, responses to unexpected data, and model design. Recent demonstrations of workflows that integrate multiple techniques and include autonomous loops, combined with emerging advancements in artificial intelligence and high throughput experimentation, signal the imminence of a revolution in materials discovery.
| S-EPMC7020936 | biostudies-literature
Project description:The chemical instability of perovskite oxides containing Sr is a critical issue for the long-term operation of solid oxide fuel cells. In this study, we demonstrate a remarkable improvement in the chemical and electrochemical stability of a heterostructured La0.6Sr0.4CoO3-δ (LSC)-Ce0.9Gd0.1O1.95 (GDC) electrode. Electrostatic spray deposition was employed to fabricate heterostructured nanoparticles in a single step with a coaxial nozzle supplying the LSC powders in the core nozzle and the GDC precursors in the shell nozzle. Moreover, the reducing fuel added to the GDC precursor solution induced the sol-gel combustion reaction in the droplet to form a uniform nanocrystalline GDC coating with high surface coverage. The high surface coverage of GDC on the LSC more significantly improved long-term stability compared with than of the bare LSC cathode at a constant current density of 1 A/cm2 at 600°C for 100 h.
| S-EPMC9035593 | biostudies-literature
Project description:A series of strontium titanates-vanadates (STVN) with nominal cation composition Sr1-xTi1-y-zVyNizO3-δ (x = 0-0.04, y = 0.20-0.40 and z = 0.02-0.12) were prepared by a solid-state reaction route in 10% H2-N2 atmosphere and characterized under reducing conditions as potential fuel electrode materials for solid oxide fuel cells. Detailed phase evolution studies using XRD and SEM/EDS demonstrated that firing at temperatures as high as 1200 °C is required to eliminate undesirable secondary phases. Under such conditions, nickel tends to segregate as a metallic phase and is unlikely to incorporate into the perovskite lattice. Ceramic samples sintered at 1500 °C exhibited temperature-activated electrical conductivity that showed a weak p(O2) dependence and increased with vanadium content, reaching a maximum of ~17 S/cm at 1000 °C. STVN ceramics showed moderate thermal expansion coefficients (12.5-14.3 ppm/K at 25-1100 °C) compatible with that of yttria-stabilized zirconia (8YSZ). Porous STVN electrodes on 8YSZ solid electrolytes were fabricated at 1100 °C and studied using electrochemical impedance spectroscopy at 700-900 °C in an atmosphere of diluted humidified H2 under zero DC conditions. As-prepared STVN electrodes demonstrated comparatively poor electrochemical performance, which was attributed to insufficient intrinsic electrocatalytic activity and agglomeration of metallic nickel during the high-temperature synthetic procedure. Incorporation of an oxygen-ion-conducting Ce0.9Gd0.1O2-δ phase (20-30 wt.%) and nano-sized Ni as electrocatalyst (≥1 wt.%) into the porous electrode structure via infiltration resulted in a substantial improvement in electrochemical activity and reduction of electrode polarization resistance by 6-8 times at 900 °C and ≥ one order of magnitude at 800 °C.
| S-EPMC8746223 | biostudies-literature
Project description:Solid oxide fuel cells (SOFCs) are inevitably affected by the tensile stress field imposed by the rigid substrate during constrained sintering, which strongly affects microstructural evolution and flaw generation in the fabrication process and subsequent operation. In the case of sintering a composite cathode, one component acts as a continuous matrix phase while the other acts as a dispersed phase depending upon the initial composition and packing structure. The clustering of dispersed particles in the matrix has significant effects on the final microstructure, and strong rigidity of the clusters covering the entire cathode volume is desirable to obtain stable pore structure. The local constraints developed around the dispersed particles and their clusters effectively suppress generation of major process flaws, and microstructural features such as triple phase boundary and porosity could be readily controlled by adjusting the content and size of the dispersed particles. However, in the fabrication of the dense electrolyte layer via the chemical solution deposition route using slow-sintering nanoparticles dispersed in a sol matrix, the rigidity of the cluster should be minimized for the fine matrix to continuously densify, and special care should be taken in selecting the size of the dispersed particles to optimize the thermodynamic stability criteria of the grain size and film thickness. The principles of constrained sintering presented in this paper could be used as basic guidelines for realizing the ideal microstructure of SOFCs.
| S-EPMC5510732 | biostudies-other