Dataset Information

Ascending thoracic aortic aneurysm growth is minimal at sizes that do not meet criteria for surgical repair.

ABSTRACT:

Background

Historic studies of nonsyndromic ascending thoracic aortic aneurysms (aTAAs) reported that the typical aTAA growth rate was approximately 0.6 mm/year, but data were limited due to relatively few studies using computed tomography (CT) imaging. Our purpose was to reevaluate the annual growth rate of nonsyndromic aTAAs that do not meet criteria for surgical repair in veterans in the contemporary era, using modern CT imaging suitable for highly accurate and reproducible aneurysm measurement.

Methods

Nonsurgical patients (diameter <5.5 cm) undergoing aneurysm surveillance at a Veterans Affairs Medical Center with repeat CT imaging performed 3 to 5 years apart were identified. Maximum diameter was determined by a single radiologist using multiplanar reformat-based measurements. Average rate of aneurysm growth was evaluated based on longest available follow-up.

Results

Sixty-seven patients were included. Average follow-up time was 4.06±0.83 years. Patients were exclusively male, with average age of 68.1±6.0 years, and the majority had a history of smoking (n=52, 78%), hypertension (n=52, 78%), and dyslipidemia (n=48, 72%). Average baseline aneurysm diameter was 44.0±3.2 mm and average growth rate was 0.11±0.31 mm/year, with no difference in growth rate between patients with initial diameter ≤45 vs. >45 mm. Only 3 patients experienced clinically significant changes in diameter with magnitude greater than 5% of baseline.

Conclusions

In this veteran population, most patients did not experience significant annual aneurysm growth over up to 5 years of follow-up, regardless of initial diameter. Thus, in the modern era, aTAAs may not grow as quickly as previously described, which will be important in determining appropriate intervals for aneurysm surveillance based upon risk-benefit ratio.

SUBMITTER: Gulati A

PROVIDER: S-EPMC8666776 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Similar Datasets

Project description:ObjectiveCurrent guidelines for elective surgery of ascending thoracic aortic aneurysms (aTAAs) use aneurysm size as primary determinant for risk stratification of adverse events. Biomechanically, dissection may occur when wall stress exceeds wall strength. Determining patient-specific aTAA wall stresses by finite element analysis can potentially predict patient-specific risk of dissection. This study compared peak wall stresses in patients with ≥5.0 cm versus <5.0 cm aTAAs to determine correlation between diameter and wall stress.MethodsPatients with aTAA ≥5.0 cm (n = 47) and <5.0 cm (n = 53) were studied. Patient-specific aneurysm geometries obtained from echocardiogram-gated computed tomography were meshed and prestress geometries determined. Peak wall stresses and stress distributions were determined using LS-DYNA finite element analysis software (LSTC Inc, Livermore, Calif), with user-defined fiber-embedded material models under systolic pressure.ResultsPeak circumferential stresses at systolic pressure were 530 ± 83 kPa for aTAA ≥5.0 cm versus 486 ± 87 kPa for aTAA <5.0 cm (P = .07), whereas peak longitudinal stresses were 331 ± 57 kPa versus 310 ± 54 kPa (P = .08), respectively. For aTAA ≥5.0 cm, correlation between peak circumferential stresses and size was 0.41, whereas correlation between peak longitudinal wall stresses and size was 0.33. However, for aTAA <5.0 cm, correlation between peak circumferential stresses and size was 0.23, whereas correlation between peak longitudinal stresses and size was 0.14.ConclusionsPeak patient-specific aTAA wall stresses overall were larger for ≥5.0 cm than aTAA <5.0 cm. Although some correlation between size and peak wall stresses was found in aTAA ≥5.0 cm, poor correlation existed between size and peak wall stresses in aTAA <5.0 cm. Patient-specific wall stresses are particularly important in determining patient-specific risk of dissection for aTAA <5.0 cm.