"Toolbox" for the Processing of Functional Polymer Composites.
Ontology highlight
ABSTRACT:
SUBMITTER: Wei Y
PROVIDER: S-EPMC8677876 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Carbon fibre reinforced polymers (CFRP) were introduced to the aerospace, automobile and civil engineering industries for their high strength and low weight. A key feature of CFRP is the polymer sizing - a coating applied to the surface of the carbon fibres to assist handling, improve the interfacial adhesion between fibre and polymer matrix and allow this matrix to wet-out the carbon fibres. In this paper, we introduce an alternative material to the polymer sizing, namely carbon nanotubes (CNTs) on the carbon fibres, which in addition imparts electrical and thermal functionality. High quality CNTs are grown at a high density as a result of a 35?nm aluminium interlayer which has previously been shown to minimise diffusion of the catalyst in the carbon fibre substrate. A CNT modified-CFRP show 300%, 450% and 230% improvements in the electrical conductivity on the 'surface', 'through-thickness' and 'volume' directions, respectively. Furthermore, through-thickness thermal conductivity calculations reveal a 107% increase. These improvements suggest the potential of a direct replacement for lightning strike solutions and to enhance the efficiency of current de-icing solutions employed in the aerospace industry.
| S-EPMC5120359 | biostudies-literature
Project description:This review presents first, rather succinctly, what are the important points to look out for when preparing good wood composites, the main types of wood composites manufactured industrially, and the mainly oil-derived wood composite adhesives and binders that dominate and have been dominating this industry. Also briefly described are the most characteristic biosourced, renewable-derived adhesives that are actively researched as substitutes. For all these adhesives, synthetic and biosourced, the reviews expose the considerable progresses which have occurred relatively recently, with a host of new approaches and ideas having been proposed and tested, some even implemented, but with even many more already appearing on the horizon.
| S-EPMC7285055 | biostudies-literature
Project description:Polymer composites consisted of small hydrophilic pockets homogeneously dispersed in a hydrophobic polymer matrix are important in many applications where controlled release of the functional agent from the hydrophilic phase is needed. As an example, a release of biomolecules or drugs from therapeutic formulations or release of salt in anti-icing application can be mentioned. Here, we report a method for preparation of such a composite material consisted of small KCOOH salt pockets distributed in the styrene-butadiene-styrene (SBS) polymer matrix and demonstrate its effectiveness in anti-icing coatings. The mixtures of the aqueous KCOOH and SBS-cyclohexane solutions were firstly stabilized by adding silica nanoparticles to the emulsions and, even more, by gelation of the aqueous phase by agarose. The emulsions were observed in optical microscope to check its stability in time and characterized by rheological measurements. The dry composite materials were obtained via casting the emulsions onto the glass substrates and evaporations of the organic solvent. Composite polymer films were characterized by water contact angle (WCA) measurements. The release of KCOOH salt into water and the freezing delay experiments of water droplets on dry composite films demonstrated their anti-icing properties. It has been concluded that hydrophobic and thermoplastic SBS polymer allows incorporation of the hydrophilic pockets/phases through our technique that opens the possibility for controlled delivering of anti-icing agents from the composite.
| S-EPMC3916421 | biostudies-literature
Project description:A composite that undergoes ionic cross-linking in the presence of salt water is presented as a viable strategy for the development of chemically responsive materials. The permeation of salt water through the composite activates embedded inorganic fillers, resulting in the release of functional ions and subsequent cross-linking with the functional groups of the polymer matrix. The release of a cross-linking agent from the inorganic filler and composite is evaluated along with the impact of the cross-linking on composite properties. The new methodology is then coupled with a dopamine-functionalized polymer in order to evaluate the potential of this approach for environmentally triggered self-healing materials.
| S-EPMC6643778 | biostudies-literature
Project description:The rapid growth of wearables has created a demand for lightweight, elastic and conformal energy harvesting and storage devices. The conducting polymer poly(3,4-ethylenedioxythiophene) has shown great promise for thermoelectric generators, however, the thick layers of pristine poly(3,4-ethylenedioxythiophene) required for effective energy harvesting are too hard and brittle for seamless integration into wearables. Poly(3,4-ethylenedioxythiophene)-elastomer composites have been developed to improve its mechanical properties, although so far without simultaneously achieving softness, high electrical conductivity, and stretchability. Here we report an aqueously processed poly(3,4-ethylenedioxythiophene)-polyurethane-ionic liquid composite, which combines high conductivity (>140 S cm-1) with superior stretchability (>600%), elasticity, and low Young's modulus (<7 MPa). The outstanding performance of this organic nanocomposite is the result of favorable percolation networks on the nano- and micro-scale and the plasticizing effect of the ionic liquid. The elastic thermoelectric material is implemented in the first reported intrinsically stretchable organic thermoelectric module.
| S-EPMC7080746 | biostudies-literature
Project description:Flexible piezoelectric materials capable of withstanding large deformation play key roles in flexible electronics. Ferroelectric ceramics with a high piezoelectric coefficient are inherently brittle, whereas polar polymers exhibit a low piezoelectric coefficient. Here we report a highly stretchable/compressible piezoelectric composite composed of ferroelectric ceramic skeleton, elastomer matrix and relaxor ferroelectric-based hybrid at the ceramic/matrix interface as dielectric transition layers, exhibiting a giant piezoelectric coefficient of 250 picometers per volt, high electromechanical coupling factor keff of 65%, ultralow acoustic impedance of 3MRyl and high cyclic stability under 50% compression strain. The superior flexibility and piezoelectric properties are attributed to the electric polarization and mechanical load transfer paths formed by the ceramic skeleton, and dielectric mismatch mitigation between ceramic fillers and elastomer matrix by the dielectric transition layer. The synergistic fusion of ultrahigh piezoelectric properties and superior flexibility in these polymer composites is expected to drive emerging applications in flexible smart electronics.
| S-EPMC10359065 | biostudies-literature
Project description:Epicuticular wax, the first protective film for numerous ground plant species, is crucial for modulating the evolution in plants. Since the waxy film is inherently thermoresponsive, many efforts focus on engineering materials for water/oil proofing, delivery, and collection, as well as microactuators by mimicking such film nature. Nonetheless, relatively fewer works address the mechanism of how the underlying substrates direct the reconstruction of waxy films while their temperature approaches the melting point. Here, we presented a strategy in which distinct frameworks of molten wax films could be examined among various substrates. Both "waxphobic" and "waxphilic" traits were first unveiled and could be achieved by the hydrophilic (water contact angle (WCA) = 42~82°) and hydrophobic (WCA = 109°) substrates, respectively. A theoretical model, based on experimental results, fluidic dynamics, and balance of surface energy, was developed to elucidate the above findings. Moreover, we demonstrated the above biomimetic epicuticular surface (BeSurface) can be applied for rewritable paper, erasable coding, and rehealable electronics without manual repairing. Remarkably, the healing time can be reduced down to 30 s, and the cycled folding test can be continued up to 500 times. All the new findings present the potentials of the BeSurface to improve the study of rehealable materials.
| S-EPMC8467712 | biostudies-literature
Project description:A typical diffraction experiment will generate many images and data sets from different crystals in a very short time. This creates a challenge for the high-throughput operation of modern synchrotron beamlines as well as for the subsequent data processing. Novice users in particular may feel overwhelmed by the tables, plots and numbers that the different data-processing programs and software packages present to them. Here, some of the more common problems that a user has to deal with when processing a set of images that will finally make up a processed data set are shown, concentrating on difficulties that may often show up during the first steps along the path of turning the experiment (i.e. data collection) into a model (i.e. interpreted electron density). Difficulties such as unexpected crystal forms, issues in crystal handling and suboptimal choices of data-collection strategies can often be dealt with, or at least diagnosed, by analysing specific data characteristics during processing. In the end, one wants to distinguish problems over which one has no immediate control once the experiment is finished from problems that can be remedied a posteriori. A new software package, autoPROC, is also presented that combines third-party processing programs with new tools and an automated workflow script that is intended to provide users with both guidance and insight into the offline processing of data affected by the difficulties mentioned above, with particular emphasis on the automated treatment of multi-sweep data sets collected on multi-axis goniostats.
| S-EPMC3069744 | biostudies-literature
Project description:The recently released National Institutes of Health Toolbox (NIHTB) batteries for neurological and behavioral function were designed to serve as standardized, common measures in clinical and epidemiological research. The current study aimed to examine constructs assessed by the self-report and parental proxy-report scales in the NIHTB Emotion Battery (NIHTB-EB) for Children by using factor analyses on data from the U.S. national normative sample of 2,916 English-speaking children. This battery contains 31 scales designed to assess both positive and negative aspects of social and emotional functioning that are considered developmentally relevant at each of three age ranges (3-7, 8-12, and 13-17 years). Results revealed four similar self-report factors for ages 8 to 12 years and 13 to 17 years. Proxy reports for ages 3 to 7 years revealed three factors, and for ages 8 to 12 years two factors. Based on the standardization sample data, age- and gender-corrected norms are presented for all NIHTB-EB individual scales and factor-based composites.
| S-EPMC6205918 | biostudies-literature
Project description:Bulk polymer-derived ceramic (PDC) composites of SiCO with an embedded graphene network were produced using graphene-coated poly(vinyl alcohol) (PVA) foams as templates. The pyrolysis of green bodies containing cross-linked polysiloxane, PVA foams, and graphene oxide (GO) resulted in the decomposition of PVA foams, compression of GO layers, and formation of graphitic domains adjacent to GO within the SiCO composite, leading to SiCO composites with an embedded graphene network. The SiCO/GO composite, with about 1.5% GO in the ceramic matrix, offered an increase in the electrical conductivity by more than 4 orders of magnitude compared to that of pure SiCO ceramics. Additionally, the unique graphene network in the SiCO demonstrated a drop in the observed thermal conductivity of the composite (∼0.8 W m-1 K-1). Young's modulus of the as-fabricated SiCO/GO composites was found to be around 210 MPa, which is notably higher than the reported values for similar composites fabricated from only ceramic precursors and PVA foams. The present approach demonstrates a facile and cost-effective method of producing bulk PDC composites with high electrical conductivity, good thermal stability, and low thermal conductivity.
| S-EPMC6641334 | biostudies-literature