Browse
Submit Data
Databases
API
Help

Dataset Information

15 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Influential Mechanism of Natural Organic Matters with Calcium Ion on the Anion Exchange Membrane Fouling Behavior via xDLVO Theory.

ABSTRACT: The fouling mechanism of the anion exchange membrane (AEM) induced by natural organic matter (NOM) in the absence and presence of calcium ions was systematically investigated via the extended Derjaguin-Landau-Verwey-Overbeek (xDLVO) approach. Sodium alginate (SA), humic acid (HA), and bovine serum albumin (BSA) were utilized as model NOM fractions. The results indicated that the presence of calcium ions tremendously aggravated the NOM fouling on the anion exchange membrane because of Ca-NOM complex formation. Furthermore, analysis of the interaction energy between the membrane surface and foulants via xDLVO revealed that short-range acid-base (AB) interaction energy played a significant role in the compositions of interaction energy during the electrodialysis (ED) process. The influence of NOM fractions in the presence of calcium ions on membrane fouling followed the order: SA > BSA > HA. This study demonstrated that the interaction energy was a dominating indicator for evaluating the tendency of anion exchange membranes fouling by natural organic matter.

SUBMITTER: Ma Z

PROVIDER: S-EPMC8706472 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Data on ion-exchange membrane fouling by humic acid during electrodialysis.

Project description:This data paper aims to provide data on the effect of the process settings on the fouling of an electrodialysis pilot installation treating a sodium chloride solution (0.1 M and 0.2 M) in the presence of humic acid (1 g/L). This data was used by "Colloidal fouling in electrodialysis: a neural differential equations model" [1] to construct a predictive model and provides interpretive insights into this dataset. 22 electrodialysis fouling experiments were performed where the electrical resistance over the electrodialysis stack was monitored while varying the crossflow velocity (2.0 cm/s - 3.5 cm/s) in the compartments, the current applied (1.41 A - 1.91 A) to the stack and the salt concentration in the incoming stream. The active cycle was maintained for a maximum of 1.5 h after which the polarity was reversed to remove the fouling layer. Additional data is gathered such as the temperature, pH, flow rate, conductivity, pressure in the different compartments of the electrodialysis stack. The data is processed to remove the effect of temperature fluctuations and some filtering is performed. To maximise the reuse potential of this dataset, both raw and processed data are provided along with a detailed description of the pilot installation and sensor locations. The data generated can be useful for researchers and industry working on electrodialysis fouling and the modelling thereof. The availability of conductivity and pH in all compartments is useful to investigate secondary effects of humic acid fouling such as the eventual decrease in membrane permselectivity or water splitting effects introduced by the fouling layer.

| S-EPMC7262420 | biostudies-literature

Anion/calcium ion ratios and proton production in some mitochondrial calcium ion uptakes.

Project description:The uptake of Ca2+ by liver mitochondria, when phosphate movement is inhibited, occurs when Co2 is present and not in its absence. Uptake of Ca2+ to form CaCO3 yields 2H+/Ca2+. Heart mitochondria, when phosphate movement is inhibited, will take up Ca2+ with the exact equivalent of hydroxybutyrate, lactate or acetate. By providing a carrier for Cl- with tributyltin, a stoicheiometric uptake of Cl- with the Ca2+ takes place. The uptakes appear to occur without significant pH change; there appears to be no CO2-dependent uptake into heart mitochondria. Oxygenation of anaerobic heart mitochondria, in the presence of an inhibitor of phosphate movement and of generation of phosphate from internal ATP, does not yield significant change of external acidity in relation to the amount of O2 added. Use of Bromothymol Blue as an indicator of the distribution of a weak acid anion confirms that the transient nature of the response of the dye distribution to Ca2+ is connected with movement of endogenous phosphate. Bromothymol Blue accumulated in response to Ca2+ is discharged when entry of the Ca2+ (in the presence of mersalyl) is mediated with nigericin. It is concluded that Ca2+ uptakes will occur alternatively with the equivalent of anions or in exchange for endogenous K+ and that proton production is connected with the changes of ionization of phosphate (unless phosphate movement is inhibited) and in liver mitochondria with the hydration of CO2.

| S-EPMC1186324 | biostudies-other

Increasing Photovoltaic Performance of an Organic Cationic Chromophore by Anion Exchange.

Project description:A symmetrical cyanine dye chromophore is modified with different counteranions to study the effect on crystal packing, polarizability, thermal stability, optical properties, light absorbing layer morphology, and organic photovoltaic (OPV) device parameters. Four sulfonate-based anions and the bulky bistriflylimide anion are introduced to the 2-[5-(1,3-dihydro-1,3,3-trimethyl-2H-indol-2-ylidene)-1,3-pentadien-1-yl]-1,3,3-trimethyl-3H-indolium chromophore using an Amberlyst A26 (OH- form) anion exchanger. Anionic charge distribution clearly correlates with device performance, whereby an average efficiency of 2% was reached in a standard bilayer organic solar. Evidence is given that the negative charge of the anion distributed over a large number of atoms is significantly more important than the size of the organic moieties of the sulfonate charge carrying group. This provides a clear strategy for future design of more efficient cyanine dyes for OPV applications.

| S-EPMC5827648 | biostudies-literature

Physically and Chemically Stable Anion Exchange Membranes with Hydrogen-Bond Induced Ion Conducting Channels.

Project description:Anion exchange membranes (AEMs) with desirable properties are the crucial components for numerous energy devices such as AEM fuel cells (AEMFCs), AEM water electrolyzers (AEMWEs), etc. However, the lack of suitable AEMs severely limits the performance of devices. Here, a series of physically and chemically stable AEMs have been prepared by the reaction between the alkyl bromine terminal ether-bond-free aryl backbone and the urea group-containing crosslinker. Morphology analyses confirm that the hydrogen bonding interaction between urea groups is capable of driving the ammonium cations to aggregate and further form continuous ion-conducting channels. Therefore, the resultant AEM demonstrates remarkable OH- conductivity (59.1 mS cm-1 at 30 °C and 122.9 mS cm-1 at 90 °C) despite a moderate IEC (1.77 mmol g-1). Simultaneously, due to the adoption of ether-bond-free aryl backbone and alkylene chain-modified trimethylammonium cation, the AEM possesses excellent alkaline stability (87.3% IEC retention after soaking in 1 M NaOH for 1080 h). Moreover, the prepared AEM shows desirable mechanical properties (tensile stress > 25 MPa) and dimensional stability (SR = 20.3% at 90 °C) contributed by the covalent-bond and hydrogen-bond crosslinking network structures. Moreover, the resulting AEM reaches a peak power density of 555 mW cm-2 in an alkaline H2/O2 single fuel cell at 70 °C without back pressure. This rational structural design presented here provides inspiration for the development of high-performance AEMs, which are crucial for membrane technologies.

| S-EPMC9696997 | biostudies-literature

Anion-exchange chromatography of phosphopeptides: weak anion exchange versus strong anion exchange and anion-exchange chromatography versus electrostatic repulsion-hydrophilic interaction chromatography.

Project description:Most phosphoproteomics experiments rely on prefractionation of tryptic digests before online liquid chromatography-mass spectrometry. This study compares the potential and limitations of electrostatic repulsion-hydrophilic interaction chromatography (ERLIC) and anion-exchange chromatography (AEX). At a pH higher than 5, phosphopeptides have two negative charges per residue and are well-retained in AEX. However, peptides with one or two phosphate groups are not separated from peptides with multiple Asp or Glu residues, interfering with the identification of phosphopeptides. At a pH of 2, phosphate residues have just a single negative charge but Asp and Glu are uncharged. This facilitates the separation of phosphopeptides from unmodified acidic peptides. Singly phosphorylated peptides are retained weakly under these conditions, due to electrostatic repulsion, unless hydrophilic interaction is superimposed in the ERLIC mode. Weak anion-exchange (WAX) and strong anion-exchange (SAX) columns were compared, with both peptide standards and a HeLa cell tryptic digest. The SAX column exhibited greater retention at pH 6 than did the WAX column. However, only about 60% as many phosphopeptides were identified with SAX at pH 6 than via ERLIC at pH 2. In one ERLIC run, 12?467 phosphopeptides were identified, including 4233 with more than one phosphate. We conclude that chromatography of phosphopeptides is best performed at low pH in the ERLIC mode. Under those conditions, the performances of the SAX and WAX materials were comparable. The data have been deposited with the ProteomeXchange with identifier PXD001333.

| S-EPMC4423237 | biostudies-other

Dihomooxacalix[4]arene-Based Fluorescent Receptors for Anion and Organic Ion Pair Recognition.

Project description:Fluorescent dihomooxacalix[4]arene-based receptors 5a-5c, bearing two naphthyl(thio)ureido groups at the lower rim via a butyl spacer, were synthesised and obtained in the cone conformation in solution. The X-ray crystal structures of 1,3- (5a) and 3,4-dinaphthylurea (5b) derivatives are reported. Their binding properties towards several anions of different geometries were assessed by 1H-NMR, UV-Vis absorption and fluorescence titrations. Structural and energetic insights of the naphthylurea 5a and 5b complexes were also obtained using quantum mechanical calculations. The data showed that all receptors follow the same trend, the association constants increase with the anion basicity, and the strongest complexes were obtained with F-, followed by the oxoanions AcO- and BzO-. Proximal urea 5b is a better anion receptor compared to distal urea 5a, and both are more efficient than thiourea 5c. Compounds 5a and 5b were also investigated as heteroditopic receptors for biologically relevant alkylammonium salts, such as the neurotransmitter γ-aminobutyric acid (GABA·HCl) and the betaine deoxycarnitine·HCl. Chiral recognition towards the guest sec-butylamine·HCl was also tested, and a 5:2 selectivity for (R)-sec-BuNH3+·Cl- towards (P) or (M) enantiomers of the inherently chiral receptor 5a was shown. Based on DFT calculations, the complex [(S)-sec-BuNH3+·Cl-/(M)-5a] was indicated as the more stable.

| S-EPMC7587342 | biostudies-literature

Anion and cation mixed-bed ion exchange for enhanced multidimensional separations of peptides and phosphopeptides.

Project description:Shotgun proteomics typically uses multidimensional LC/MS/MS analysis of enzymatically digested proteins, where strong cation-exchange (SCX) and reversed-phase (RP) separations are coupled to increase the separation power and dynamic range of analysis. Here we report an on-line multidimensional LC method using an anion- and cation-exchange mixed bed for the first separation dimension. The mixed-bed ion-exchange resin improved peptide recovery over SCX resins alone and showed better orthogonality to RP separations in two-dimensional separations. The Donnan effect, which was enhanced by the introduction of fixed opposite charges in one column, is proposed as the mechanism responsible for improved peptide recovery by producing higher fluxes of salt cations and lower populations of salt anions proximal to the SCX phase. An increase in orthogonality was achieved by a combination of increased retention for acidic peptides and moderately reduced retention of neutral to basic peptides by the added anion-exchange resin. The combination of these effects led to approximately 100% increase in the number of identified peptides from an analysis of a tryptic digest of a yeast whole cell lysate. The application of the method to phosphopeptide-enriched samples increased by 94% phosphopeptide identifications over SCX alone. The lower pKa of phosphopeptides led to specific enrichment in a single salt step resolving acidic phosphopeptides from other phospho- and non-phosphopeptides. Unlike previous methods that use anion exchange to alter selectivity or enrich phosphopeptides, the proposed format is unique in that it works with typical acidic buffer systems used in electrospray ionization, making it feasible for online multidimensional LC/MS/MS applications.

| S-EPMC2538959 | biostudies-literature

Base-Resistant Ionic Metal-Organic Framework as a Porous Ion-Exchange Sorbent.

Project description:A systematic approach has been employed to obtain a hydrolytically stable cationic metal-organic framework (MOF). The synthesized two-dimensional Ni(II)-centered cationic MOF, having its backbone built from purely neutral N-donor ligand, is found to exhibit uncommon resistance over wide pH range, particularly even under highly alkaline conditions. This report presents a rare case of a porous MOF retaining structural integrity under basic conditions, and an even rarer case of a porous cationic MOF. The features of stability and porosity in this ionic MOF have been harnessed for the function of charge- and size-selective capture of small organic dye through ion-exchange process across a wide pH range.

| S-EPMC6137287 | biostudies-literature

Polystyrene-Based Hydroxide-Ion-Conducting Ionomer: Binder Characteristics and Performance in Anion-Exchange Membrane Fuel Cells.

Project description:Polystyrene-based polymers with variable molecular weights are prepared by radical polymerization of styrene. Polystyrene is grafted with bromo-alkyl chains of different lengths through Friedel-Crafts acylation and quaternized to afford a series of hydroxide-ion-conducting ionomers for the catalyst binder for the membrane electrode assembly in anion-exchange membrane fuel cells (AEMFCs). Structural analyses reveal that the molecular weight of the polystyrene backbone ranges from 10,000 to 63,000 g mol-1, while the ion exchange capacity of quaternary-ammonium-group-bearing ionomers ranges from 1.44 to 1.74 mmol g-1. The performance of AEMFCs constructed using the prepared electrode ionomers is affected by several ionomer properties, and a maximal power density of 407 mW cm-2 and a durability exceeding that of a reference cell with a commercially available ionomer are achieved under optimal conditions. Thus, the developed approach is concluded to be well suited for the fabrication of next-generation electrode ionomers for high-performance AEMFCs.

| S-EPMC7956690 | biostudies-literature

Extracellular Calcium Ion Concentration Regulates Chondrocyte Elastic Modulus and Adhesion Behavior.

Project description:Extracellular calcium ion concentration levels increase in human osteoarthritic (OA) joints and contribute to OA pathogenesis. Given the fact that OA is a mechanical problem, the effect of the extracellular calcium level ([Ca2+]) on the mechanical behavior of primary human OA chondrocytes remains to be elucidated. Here, we measured the elastic modulus and cell-ECM adhesion forces of human primary chondrocytes with atomic force microscopy (AFM) at different extracellular calcium ion concentration ([Ca2+]) levels. With the [Ca2+] level increasing from the normal baseline level, the elastic modulus of chondrocytes showed a trend of an increase and a subsequent decrease at the level of [Ca2+], reaching 2.75 mM. The maximum increment of the elastic modulus of chondrocytes is a 37% increase at the peak point. The maximum unbinding force of cell-ECM adhesion increased by up to 72% at the peak point relative to the baseline level. qPCR and immunofluorescence also indicated that dose-dependent changes in the expression of myosin and integrin β1 due to the elevated [Ca2+] may be responsible for the variations in cell stiffness and cell-ECM adhesion. Scratch assay showed that the chondrocyte migration ability was modulated by cell stiffness and cell-ECM adhesion: as chondrocyte's elastic modulus and cell-ECM adhesion force increased, the migration speed of chondrocytes decreased. Taken together, our results showed that [Ca2+] could regulate chondrocytes stiffness and cell-ECM adhesion, and consequently, influence cell migration, which is critical in cartilage repair.

| S-EPMC8468569 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data