Browse
Submit Data
Databases
API
Help

Dataset Information

28 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Influence of Carbon Black and Silica Fillers with Different Concentrations on Dielectric Relaxation in Nitrile Butadiene Rubber Investigated by Impedance Spectroscopy.

ABSTRACT: In neat nitrile butadiene rubber (NBR), three relaxation processes were identified by impedance spectroscopy: α and α' processes and the conduction contribution. We investigated the effects of different carbon black (CB) and silica fillers with varying filler content on the dielectric relaxations in NBR by employing a modified dispersion analysis program that deconvolutes the corresponding processes. The central frequency for the α' process with increasing high abrasion furnace (HAF) CB filler was gradually upshifted at room temperature, while the addition of silica led to a gradual downshift of the center frequency. The activation energy behavior for the α' process was different from that for the central frequency. The use of HAF CB led to a rapid increase in DC conductivity, resulting from percolation. The activation energy for the DC conductivity of NBRs with HAF CB decreased with increasing filler, which is consistent with that reported in different groups.

SUBMITTER: Kim GH

PROVIDER: S-EPMC8747209 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Rheological and Mechanical Properties of Silica/Nitrile Butadiene Rubber Vulcanizates with Eco-Friendly Ionic Liquid.

Project description:In this paper we designed greener rubber nanocomposites exhibiting high crosslinking density, and excellent mechanical and thermal properties, with a potential application in technical fields including high-strength and heat-resistance products. Herein 1-ethyl-3-methylimidazolium acetate ([EMIM]OAc) ionic liquid was combined with silane coupling agent to formulate the nanocomposites. The impact of [EMIM]OAc on silica dispersion in a nitrile rubber (NBR) matrix was investigated by a transmission electron microscope and scanning electron microscopy. The combined use of the ionic liquid and silane in an NBR/silica system facilitates the homogeneous dispersion of the silica volume fraction (φ) from 0.041 to 0.177 and enhances crosslinking density of the matrix up to three-fold in comparison with neat NBR, and also it is beneficial for solving the risks of alcohol emission and ignition during the rubber manufacturing. The introduction of ionic liquid greatly improves the mechanical strength (9.7 MPa) with respect to neat NBR vulcanizate, especially at high temperatures e.g., 100 °C. Furthermore, it impacts on rheological behaviors of the nanocomposites and tends to reduce energy dissipation for the vulcanizates under large amplitude dynamic shear deformation.

| S-EPMC7700482 | biostudies-literature

Surface Treatment Effects on the Mechanical Properties of Silica Carbon Black Reinforced Natural Rubber/Butadiene Rubber Composites.

Project description:For the first time, phenolic formaldehyde resin (PF)-treated silica carbon black (SiCB) were prepared with different treatment conditions and their effect as fillers on the mechanical properties of filler filled natural rubber/butadiene rubber (NR/BR) composites were investigated in detail. The PF coating layer on the SiCB derived from rusk husk not only promoted the dispersion of the fillers but also improved the interfacial interactions between fillers and the rubber matrix. As a result, both the cross-link density and mechanical properties of the obtained composites were effectively enhanced. The filler SiCB with 3 wt % PF surface treatment greatly improved the tensile strength of NR/BR composites and reached 7.1 MPa, which increased by 73.7% compared with that of SiCB-filled NR/BR composites. The improved interfacial interactions promoted higher energy dissipation, leading to simultaneously enhancing the glass transition temperature of the obtained composites. Due to the easy processing and low cost of filler as well as the effectively enhanced mechanical properties of composites, the PF-coating methodology has a great potential for practical applications in SiCB reinforced high-performance composites. A commercial filler, carbon black (N774), was also used in this study and evaluated under the same conditions for comparison.

| S-EPMC6918317 | biostudies-literature

Hybrid Silica-Based Fillers in Nanocomposites: Influence of Isotropic/Isotropic and Isotropic/Anisotropic Fillers on Mechanical Properties of Styrene-Butadiene (SBR)-Based Rubber.

Project description:The improvement of mechanical properties of polymer-based nanocomposites is usually obtained through a strong polymer-silica interaction. Most often, precipitated silica nanoparticles are used as filler. In this work, we study the synergetic effect occurring between dual silica-based fillers in a styrene-butadiene rubber (SBR)/polybutadiene (PBD) rubber matrix. Precipitated Highly Dispersed Silica (HDS) nanoparticles (10 nm) have been associated with spherical Stöber silica nanoparticles (250 nm) and anisotropic nano-Sepiolite. By imaging filler at nano scale through Scanning Transmission Electron Microscopy, we have shown that anisotropic fillers align only in presence of a critical amount of HDS. The dynamic mechanical analysis of rubber compounds confirms that this alignment leads to a stiffer nanocomposite when compared to Sepiolite alone. On the contrary, spherical 250 nm nanoparticles inhibit percolation network and reduce the nanocomposite stiffness.

| S-EPMC8348337 | biostudies-literature

Actuator Performance of a Hydrogenated Carboxylated Acrylonitrile-Butadiene Rubber/Silica-Coated BaTiO<sub>3</sub> Dielectric Elastomer.

Project description:We synthesized silica-coated barium titanate (BaTiO3) particles with different silica shell thicknesses and evaluated the effect of silica coating on the relative dielectric properties of silica-coated BaTiO3 particles. Furthermore, composite elastomers were prepared using hydrogenated carboxylated acrylonitrile-butadiene rubber (HXNBR) with a high relative dielectric constant (εr) and silica-coated BaTiO3 particles, and their performance as an actuator was evaluated. Both εr and relative dielectric loss of non-coated BaTiO3 particles increased at low frequencies (<200 Hz) associated with ionic conduction. However, εr and relative dielectric loss were reduced for the silica-coated BaTiO3 particles with thick silica shells, indicating that silica coating reduced ion migration. The dielectric breakdown strength increased with the thickness of the silica shell; it increased up to 80 V/μm for HXNBR/silica-coated BaTiO3 particles with 20 nm-thick silica shells. The maximum generated stress, strain, and output energy density of the composite elastomer with HXNBR (with a high relative constant) and silica-coated BaTiO3 were 1.0 MPa, 7.7%, and 19.4 kJ/m3, respectively. In contrast, the values of the same parameters for a reference elastomer (acrylic/BaTiO3; with low εr) were 0.4 MPa, 6.7%, and 6.8 kJ/m3 at the dielectric breakdown strength of 70 V/μm. The results indicated that the elastomers composed of HXNBR and silica-coated BaTiO3 exhibited higher generated stress, strain, and output energy density than elastomers for conventional dielectric actuators.

| S-EPMC7807772 | biostudies-literature

Molecular simulations of gas transport in hydrogenated nitrile butadiene rubber and ethylene-propylene-diene rubber.

Project description:Diffusion and sorption of five gases (H2, N2, O2, CO2, CH4) in hydrogenated nitrile butadiene rubber (HNBR) and ethylene-propylene-diene rubber (EPDM) have been investigated by molecular dynamics (MD) and grand canonical Monte Carlo (GCMC) simulations. The diffusion coefficients of gas molecules in HNBR and EPDM are well correlated with the effective penetrant diameter except for CO2. CO2 shows a lower diffusion coefficient due to its linear shape. Additionally, the favorable interaction between CO2 and HNBR is another factor for its lower diffusion coefficient in HNBR. HNBR shows lower diffusion coefficients than EPDM. This is because the polar -CN groups in HNBR chains increase interchain cohesion and result in tight intermolecular packing, low free volume and poor chain mobility, which decreases the diffusion coefficients of HNBR. The solubility coefficients of CH4, O2, N2 and H2 in HNBR are lower than those in EPDM, which is a result of the weak HNBR-penetrant interactions and low free volume of HNBR. However, the solubility coefficient of CO2 in HNBR is higher than in EPDM. This is attributed to the strong interaction between CO2 and HNBR. H2, O2, N2 and CH4 show lower permeability coefficients in HNBR than in EPDM, while CO2 has higher permeability coefficients in HNBR. These molecular details provide critical information for the understanding of structures and gas transport between HNBR and EPDM.

| S-EPMC9051154 | biostudies-literature

Li-Rich Antiperovskite/Nitrile Butadiene Rubber Composite Electrolyte for Sheet-Type Solid-State Lithium Metal Battery.

Project description:Lithium-rich antiperovskites (LiRAPs) hold great promise to be the choice of solid-state electrolytes (SSEs) owing to their high ionic conductivity, low activation energy, and low cost. However, processing sheet-type solid-state Li metal batteries (SSLiB) with LiRAPs remains challenging due to the lack of robust techniques for battery processing. Herein, we propose a scalable slurry-based procedure to prepare a flexible composite electrolyte (CPE), in which LiRAP (e.g., Li2OHCl0.5Br0.5, LOCB) and nitrile butadiene rubber (NBR) serve as an active filler and as a polymer scaffold, respectively. The low-polar solvent helps to stabilize the LiRAP phase during slurry processing. It is found that the addition of LOCB into the NBR polymer enhances the Li ion conductivity for 2.3 times at 60°C and reduces the activation energy (max. 0.07 eV). The as-prepared LOCB/NBR CPE film exhibits an improved critical current of 0.4 mA cm-2 and can stably cycle for over 1000 h at 0.04 mA cm-2 under 60°C. In the SSLiB with the sheet-type configuration of LiFePO4(LFP)||LOCB/NBR CPE||Li, LFP exhibits a capacity of 137 mAh/g under 60 at 0.1°C. This work delivers an effective strategy for fabrication of LiRAP-based CPE film, advancing the LiRAP-family SSEs toward practical applications.

| S-EPMC8634478 | biostudies-literature

Temperature dependence of the interfacial bonding characteristics of silica/styrene butadiene rubber composites: a molecular dynamics simulation study.

Project description:Based on our previous studies on the modification of in-chain styrene butadiene rubber (SBR) using 3-mercaptopropionic acid as well as its composites filled with silica, we further constructed two types of models (amorphous and layered) to investigate the temperature dependence of the interfacial bonding characteristics of silica/SBR composites via molecular dynamics (MD) simulation. The competing effects of rubber-rubber interactions and filler-rubber interactions were identified, and the relationship between the competing effects and the temperature was determined. Besides this, the effect of temperature on the mobility and distribution of SBR chains on the surface of silica was investigated. It was found that the stronger the interfacial interactions, the less sensitive the motion of SBR chains to temperature. Finally, the number and length of hydrogen bonds as a function of temperature were analyzed. These simulated results deepened the understanding of interface temperature dependence of the silica/SBR composites and gave a molecular level explanation for the existence of an optimum modifier content (14.2 wt%) that is temperature independent.

| S-EPMC9076183 | biostudies-literature

Multiscale Simulation on Product Distribution from Pyrolysis of Styrene-Butadiene Rubber.

Project description:Pyrolysis of styrene-butadiene rubber receives renewed attention due to its application in tackling the waste tire disposal problem while allowing energy recovery. The density functional theory calculation (DFT) and ReaxFF molecular dynamics simulation (MD) are adopted to study the pyrolysis process with the variation of temperature and pressure. The bond dissociation energies of intramonomer and intermonomer bonds in trimers with different linking methods are calculated by DFT, where the bond with low energy tends to break during the pyrolysis process. The following MD simulation shows the pyrolysis product distribution of chain segments in styrene-butadiene rubber, where bond breaking positions in MD agree well with corresponding results in DFT and experiment. The next nearest neighbor bonds (single bonds) connected with double bond or benzene usually have lower dissociation energies than other single bonds and prone to break during the pyrolysis process. And thus, the intermonomer bonds tend to break at relatively low temperatures (around 650 K in experiment) prior to intramonomer bonds, which result in the emergence of monomers. With the temperature increase, intramonomer bonds are broken and thus large fragments are further pyrolyzed into small ones (e.g., C2 and C). Besides, the pressure strongly influences the product distribution, where high pressures promote the occurrence of secondary reactions.

| S-EPMC6960849 | biostudies-literature

Styrene-Butadiene Rubber by Miniemulsion Polymerization Using In Situ Generated Surfactant.

Project description:An alternative approach for the synthesis of styrene butadiene rubber (SBR) copolymer latexes was explored in order to obtain low gel fractions and high solid contents. The ultra-turrax-assisted miniemulsion stabilized by in situ surfactant generation was adopted as the main strategy since this technique can inhibit the eventual presence of secondary nucleation producing polybutadiene particles and also control the cross-linking degree. Styrene monomer was first miniemulsified using an ultra-turrax and in situ generated surfactant using either hexadecane (HD) or octadecyl acrylate (ODA) as the hydrophobe. Dynamic light scattering (DLS) measurements of droplet size indicated faster stabilization and the production of smaller droplet diameters ca. 190 nm (PdI = 0.08) when employing in situ generated potassium oleate (K-Oleate) in comparison to SDS-based miniemulsions. High butadiene-level SBR latexes with ca. 50% solids content, a glass transition temperature (Tg) of -52 °C, and a butadiene to styrene weight ratio of 75:25, were then obtained using the miniemulsion droplets as seeds. Turbiscan and DLS measurements revealed a very stable resulting latex with SBR particle diameter of ca. 220 nm and a low polydispersity index (PdI). Secondary nucleation was prevented as indicated by the low Np/Nd value. Cryo-TEM images showed a narrow distribution of particle size as well as the absence of agglomeration. The gel content was below 10% when tert-dodecyl mercaptan (t-DM) was used as chain transfer agent (CTA).

| S-EPMC7408609 | biostudies-literature

Thermal Stability and Flammability of Styrene-Butadiene Rubber-Based (SBR) Ceramifiable Composites.

Project description:Ceramifiable styrene-butadiene (SBR)-based composites containing low-softening-point-temperature glassy frit promoting ceramification, precipitated silica, one of four thermally stable refractory fillers (halloysite, calcined kaolin, mica or wollastonite) and a sulfur-based curing system were prepared. Kinetics of vulcanization and basic mechanical properties were analyzed and added as Supplementary Materials. Combustibility of the composites was measured by means of cone calorimetry. Their thermal properties were analyzed by means of thermogravimetry and specific heat capacity determination. Activation energy of thermal decomposition was calculated using the Flynn-Wall-Ozawa method. Finally, compression strength of the composites after ceramification was measured and their micromorphology was studied by scanning electron microscopy. The addition of a ceramification-facilitating system resulted in the lowering of combustibility and significant improvement of the thermal stability of the composites. Moreover, the compression strength of the mineral structure formed after ceramification is considerably high. The most promising refractory fillers for SBR-based ceramifiable composites are mica and halloysite.

| S-EPMC5456863 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data