Biocompatibility and Comfort during Extended Wear of Mel4 Peptide-Coated Antimicrobial Contact Lenses.
Ontology highlight
ABSTRACT:
SUBMITTER: Kalaiselvan P
PROVIDER: S-EPMC8772808 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Poly(vinylpyrrolidone) (PVP-K90) is widely used to manage dry eye syndrome (DES). The marketed eye drop solutions (high dose) need frequent instillation, affecting the routine lifestyle of patients. PVP-K90-laden contact lenses can be used to overcome the limitations of eye drop solutions (low bioavailability and frequent instillation). However, the conventional methods of PVP-K90 loading show poor loading capacity and short duration of effect. In the present study, we have developed PVP-K90-coated contact lenses via a short curing approach to increase the PVP-K90 loading capacity with a sustained release profile to manage dry eye syndrome. PVP-K90 was loaded by a soaking method (SM-PVP), direct loading (during fabrication, DL-PVP), a combination of soaking and direct loading (DL-SM-PVP), and a novel coating process (SM-PVP-C and DL-SM-PVP-C). The swelling studies suggested improvement in the water uptake (hydration) property of the contact lenses due to the presence of PVP-K90. The optical transparency was within an acceptable range. The in vitro release of PVP-K90 was in the following order: PVP-coated contact lens (168 h) > DL-SM-PVP (168 h) > DL-PVP (96 h) > SM-PVP (72-96 h). PVP-coated contact lenses showed a high burst effect (lubricating effect) and sustained release (3161-448 ng/h between 24 and 168 h) due to high PVP loading/coating in comparison to the uncoated respective contact lenses (964-113 ng/h between 24 and 96 h). In animal studies, the PVP-K90-coated contact lens showed higher tear volume in comparison to the respective uncoated contact lenses and an eye drop solution. This study demonstrates a novel approach of coating a high amount of PVP-K90 on contact lenses for sustained release to manage several ocular diseases like dry eye syndrome, conjunctivitis, and other ocular injuries.
| S-EPMC7391853 | biostudies-literature
Project description:The geometry of contact lenses can be altered by wear but determining the changes that occur in soft contact lenses (SCLs) is challenging. This study aimed to investigate the shape alterations of daily disposable SCLs after wear using swept-source optical coherence tomography (SS-OCT). Forty-five eyes with myopia of - 3.00 diopters (D) were enrolled. The participants wore three types of SCLs: hydrogel lens (nesofilcon A) and silicone hydrogel lenses (delefilcon A and stenfilcon A). The SCLs were scanned 3-6 min after lens removal. We found a significant decrease in the SCL anterior curvature: 0.24 ± 0.17 mm for nesofilcon A, 0.44 ± 0.21 mm for delefilcon A, and 0.53 ± 0.29 mm for stenfilcon A. The changes in the anterior curvature of SCLs correlated moderately with the mean corneal keratometry; Pearson's correlation coefficients for nesofilcon A and delefilcon A were 0.57 and 0.52, respectively (P < 0.001). A statistically significant change in the total diameter was observed in SCL made of stenfilcon A (0.39 mm, P < 0.001). To conclude, the central radii of curvature decreased after a wearing period for all three types of daily disposable SCLs to imitate the anterior corneal surface, however, the changes in other geometrical parameters measured with SS-OCT were lens-specific.
| S-EPMC8203656 | biostudies-literature
Project description:Contact lens wear causes mutual interactions between the ocular surface and the lens, which may affect comfort as well as vision. The aim of this study was to examine deformations in modern positive- and negative-powered silicone hydrogel soft contact lenses (SiH SCLs) after 7 days of continuous wear. This pre-post interventional study included 64 eyes: 42 eyes with myopia of -3.00 D and 22 eyes with hyperopia of +3.00 D. All patients underwent general ophthalmic examination, corneal topography/tomography, total corneal and epithelial thickness mapping, and specular microscopy before and after the wearing period. SiH SCLs made of senofilcon A were worn continuously for 7 days on all eligible eyes. The geometry of the new and used lenses was measured 3 to 6 minutes after removal in two perpendicular planes using a custom-made swept source optical coherence tomography (SS-OCT) system for in vitro measurements. The anterior and posterior radii of curvature decreased in -3.00 D lenses in two perpendicular planes. This effect correlated significantly with average keratometry of the cornea. Sagittal lens height was lower in +3.00 D lens after wear, which correlated moderately with the corneal sagittal height. A significant decrease in central corneal epithelial thickness was observed after wearing +3.0 D lenses. In conclusion, SiH SCLs made of senofilcon A undergo minor deformations after 7-day continuous wear. Geometry modifications are different for -3.00 D and +3.00 D lenses, and they imitate the shape of the anterior eye surface. These geometric changes are accompanied by a decrease in the central thickness of corneal epithelium after +3.00 D lens wear.
| S-EPMC7652269 | biostudies-literature
Project description:PurposeThis study determined which microbiologic, clinical, demographic, and behavioral factors are associated with corneal infiltrative events (CIEs) during continuous wear of silicone hydrogel (SH) contact lenses.MethodsSubjects (n = 205) were fitted with lotrafilcon A lenses for continuous wear and observed for 1 year. The main exposures of interest were corneal staining and bacterial lens contamination. Kaplan-Meier (KM) plots were used to estimate the cumulative unadjusted probability of remaining CIE free, and Cox proportional hazards regression was used to model the hazard of having a CIE, as a function of key predictor variables.ResultsThe KM-unadjusted cumulative probability of remaining CIE free was 73.3%. Approximately 53% of subjects had repeated episodes of corneal staining (mild or greater), and 11.3% had repeated episodes of moderate or greater corneal staining. Corneal staining was not associated with the development of a CIE. The frequency of substantial bacterial bioburden on worn lenses at the time of a CIE was 64.7%, compared with only 12.2% during uncomplicated wear. The presence of substantial lens bacterial bioburden was associated with the development of a CIE (adjusted hazards ratio [HR], 8.66; 95% confidence interval [CI], 2.88-26.01). Smoking was also associated with a CIE (adjusted HR, 4.13; 95% CI, 1.27-13.45).ConclusionsCorneal staining is common during continuous wear of SH lenses, but it is not associated with the development of a CIE. Smoking and substantial lens bacterial bioburden pose prominent risks of a CIE. In this study, more than 70% of the total risk of CIE in those with substantial lens bioburden is attributable to this exposure. (ClinicalTrials.gov number, NCT00727402).
| S-EPMC3061493 | biostudies-literature
Project description:PurposeTo compare the visual performance of prototype contact lenses designed via deliberate manipulation of higher-order spherical aberrations to extend-depth-of-focus with two commercial multifocals, after 1 week of lens wear.MethodsIn a prospective, participant-masked, cross-over, randomized, 1-week dispensing clinical-trial, 43 presbyopes [age: 42-63 years] each wore AIROPTIX Aqua multifocal (AOMF), ACUVUE OASYS for presbyopia (AOP) and extended-depth-of-focus prototypes (EDOF) appropriate to their add requirements. Measurements comprised high-contrast-visual-acuity (HCVA) at 6m, 70cm, 50cm and 40cm; low-contrast-visual-acuity (LCVA) and contrast-sensitivity (CS) at 6m and stereopsis at 40cm. A self-administered questionnaire on a numeric-rating-scale (1-10) assessed subjective visual performance comprising clarity-of-vision and lack-of-ghosting at various distances during day/night-viewing conditions and overall-vision-satisfaction.ResultsEDOF was significantly better than AOMF and AOP for HCVA averaged across distances (p≤0.038); significantly worse than AOMF for LCVA (p=0.021) and significantly worse than AOMF for CS in medium and high add-groups (p=0.006). None of these differences were clinically significant (≤2 letters). EDOF was significantly better than AOMF and AOP for mean stereoacuity (36 and 13 seconds-of-arc, respectively: p≤0.05). For clarity-of-vision, EDOF was significantly better than AOP at all distances and AOMF at intermediate and near (p≤0.028). For lack-of-ghosting averaged across distances, EDOF was significantly better than AOP (p<0.001) but not AOMF (p=0.186). EDOF was significantly better than AOMF and AOP for overall-vision-satisfaction (p≤0.024).ConclusionsEDOF provides better intermediate and near vision performance than either AOMF or AOP with no difference for distance vision after 1 week of lens wear.
| S-EPMC5777928 | biostudies-literature
Project description:PurposeTo determine the association between mucin ball formation and corneal infiltrative events (CIEs) during continuous wear with lotrafilcon A silicone hydrogel contact lenses.MethodsSubjects (n = 205) in the Longitudinal Analysis of Silicone Hydrogel Contact Lens Study wore lotrafilcon A contact lenses for 12 months of continuous wear. The primary outcome was a CIE. Kaplan-Meier methods were used to estimate the unadjusted cumulative incidence of remaining CIE free stratified by mucin ball presence. Cox proportional hazards regression was used to model the hazard of developing a CIE as a function of mucin ball formation and other covariates.ResultsOver half (54.2%) of the subjects displayed some presence of mucin balls during at least 1 visit and about one third (32.8%) displayed repeated episodes. Mucin ball scores were correlated between the 2 eyes and weakly correlated with corneal curvature (P ≤ 0.005). Univariate analyses revealed that the relative hazard for a CIE was 0.35 [95% confidence interval (CI), 0.19-0.68] if a single episode of mucin balls was detected and 0.17 (95% CI, 0.06-0.43) if repeated episodes were detected. Upon multivariate analysis, repeated presence of mucin balls was associated with an 84% decreased hazard of experiencing a CIE (hazard ratio: 0.16; 95% CI, 0.06-0.44).ConclusionsThe presence of mucin balls is significantly associated with a decreased incidence of CIEs, and the effect is greatest when they are repeatedly present over time. We hypothesize that the mucin ball presence represents a more concentrated or viscous mucus layer, which prevents upregulation of the immune response against bacterial ligands.
| S-EPMC3596007 | biostudies-literature
Project description:IntroductionSoft contact lens wearers are often prescribed the same lens material and modality for multiple years if patients express satisfaction and no significant problems with lens fit or ocular health are noted upon evaluation. Despite their satisfaction, it is possible that other lenses exist that could provide additional health or convenience benefits and still provide satisfied lens wear experience.MethodsIn this study, wearers of a specific monthly replacement lens brand (comfilcon A) were recruited for an open-label study. The habitual contact lens prescription was optimized for 2 weeks of wear and participants confirmed that they were satisfied with their habitual lenses before being refit with daily disposable lenses (verofilcon A). Participants responded to visual analog scale (VAS) survey about their initial impressions of the lenses. After 2 weeks of lens wear, participants completed a final study visit and completed surveys about lens wear experiences with the daily disposable study lenses.ResultsFifteen male and 15 female participants completed the study. Median (IQR) binocular LogMAR visual acuity was -0.20(0.12), which is equivalent to 10/12.5 Snellen acuity. Initial impression surveys revealed median (interquartile range) of 92.5(22.3) for quality of vision; 95.0(19.3) for comfort; and 91.5(19.3) for satisfaction. At the final visit, median scores for EOD quality of vision was 86.5(24.0); EOD comfort was 84.5(30.3), and EOD dryness 25.5(47.0). Median overall VAS scores were 92.5(16.0) for vision; 88.0(18.3) for comfort, and 17.5(25.8) for dryness. Median satisfaction with the study lenses was scored 9(2.8) on a 1-10 scale.ConclusionsIn this study, satisfied wearers of comfilcon A reusable lens were refit with Verofilcon A daily disposable lenses and showed high satisfaction scores with the new lenses, showing that refitting these patients can allow patients to have lenses with more frequent replacement and maintain satisfaction with daily lens wear.
| S-EPMC10506162 | biostudies-literature
Project description:Contact lens is a ubiquitous technology used for vision correction and cosmetics. Sensing in contact lenses has emerged as a potential platform for minimally invasive point-of-care diagnostics. Here, a microlithography method is developed to fabricate microconcavities and microchannels in a hydrogel-based contact lens via a combination of laser patterning and embedded templating. Optical microlithography parameters influencing the formation of microconcavities including ablation power (4.3 W) and beam speed (50 mm s-1 ) are optimized to control the microconcavity depth (100 µm) and diameter (1.5 mm). The fiber templating method allows the production of microchannels having a diameter range of 100-150 µm. Leak-proof microchannel and microconcavity connections in contact lenses are validated through flow testing of artificial tear containing fluorescent microbeads (Ø = 1-2 µm). The microconcavities of contact lenses are functionalized with multiplexed fluorophores (2 µL) to demonstrate optical excitation and emission capability within the visible spectrum. The fabricated microfluidic contact lenses may have applications in ophthalmic monitoring of metabolic disorders at point-of-care settings and controlled drug release for therapeutics.
| S-EPMC6607692 | biostudies-literature
Project description:PurposeTo determine whether Mel4-coated antimicrobial contact lenses (MACLs) can reduce the incidence of corneal infiltrative events (CIEs) during extended wear.MethodsA prospective, randomized, double-masked, single-center, contralateral, extended contact lens wear clinical trial was conducted with 176 subjects. Each participant was randomly assigned to wear a MACL in one eye and an uncoated control contact lens in the contralateral eye or an extended-wear biweekly disposable modality for 3 months. The main outcome measures were the incidence of CIEs per 100 eye-months, identification of the microbial types colonizing the contact lenses or eyes at the time of the CIEs, and their susceptibility to Mel4.ResultsNine participants (5.1%) experienced unilateral CIEs; six participants had contact lens acute red eye, and three participants had infiltrative keratitis. The incidence rate for CIEs (0.4 events per 100 participant months; 1.7%) in the Mel4-coated lenses (test) was 69% less than that of the control lenses (1.3 events per 100 participant months; 3.4%; P = 0.29). All Gram-negative bacteria isolated from lenses and lids of participants with CIEs (Citrobacter diversus, Acinetobacter haemolyticus, and Acinetobacter lwoffii) were susceptible to Mel4 peptide; minimum inhibitory concentrations ranged from 15.6 to 62.5 µg/mL. Reduction of adhesion of these bacteria by Mel4-coated lenses ranged from 2.1 to 2.2 log10 colony-forming units/lens.ConclusionsMACLs had the capacity to reduce CIEs by at least 50% compared with uncoated control lenses during extended wear over 3 months; however, due to the relatively low rates of CIEs, the reduction was not statistically different compared with control lenses.Translational relevanceThis study provides evidence that antimicrobial contact lenses have the potential to reduce the incidence of corneal infiltrative events during extended wear.
| S-EPMC8254012 | biostudies-literature
Project description:Although the manufacturing processes of contact lenses are well established, the use of additive manufacturing for their fabrication opens many new possibilities to explore. The current study demonstrates the fabrication of personalized smart contract lenses utilizing additive manufacturing. The study includes 3-dimensional (3D) modeling of contact lenses with the assistance of a computer aided designing tool based on standard commercial contact lens dimension, followed by the selection of the suitable materials and 3D printing of contact lenses. The 3D printing parameters were optimized to achieve the desired lens geometries, and a post processing treatment was performed to achieve a smooth surface finish. The study also presents functionalized contact lenses with built-in sensing abilities by utilizing microchannels at the contact lens edges. Tinted contact lenses were printed and nanopatterns were textured onto the contact lens surfaces through holographic laser ablation. 3D printed contact lenses have advantages over conventional contact lenses, offering customized ophthalmic devices and the capability to integrate with optical sensors for diagnostics.
| S-EPMC8396802 | biostudies-literature