Droplet evaporation on porous fabric materials.
Ontology highlight
ABSTRACT:
SUBMITTER: Goncalves M
PROVIDER: S-EPMC8776847 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Liquid-filled porous materials exist widely in nature and engineering fields, with the diffusion of substances in them playing an important role in system functions. Although surface evaporation is often inevitable in practical scenarios, the evaporation effects on diffusion behavior in liquid-filled porous materials have not been well explored yet. In this work, we performed noninvasive diffusion imaging experiments to observe the diffusion process of erioglaucine disodium salt dye in a liquid-filled nitrocellulose membrane under a wide range of relative humidities (RHs). We found that evaporation can significantly accelerate the diffusion rate and alter concentration distribution compared with the case without evaporation. We explained the accelerated diffusion phenomenon by the mechanism that evaporation would induce a weak flow in liquid-filled porous materials, which leads to convective diffusion, i.e., evaporation-induced flow and diffusion (EIFD). Based on the EIFD mechanism, we proposed a convective diffusion model to quantitatively predict the diffusion process in liquid-filled porous materials under evaporation and experimentally validated the model. Introducing the dimensionless Peclet (P e) number to measure the relative contribution of the evaporation effect to pure molecular diffusion, we demonstrated that even at a high RH of 95%, where the evaporation effect is usually assumed negligible in common sense, the evaporation-induced diffusion still overwhelms the molecular diffusion. The flow velocity induced by evaporation in liquid-filled porous materials was found to be 0.4-5 μm/s, comparable to flow in many biological and biomedical systems. The present analysis may help to explain the driving mechanism of tissue perfusion and provide quantitative analysis or inspire new control methods of flow and material exchange in numerous cutting-edge technologies, such as paper-based diagnostics, hydrogel-based flexible electronics, evaporation-induced electricity generation, and seawater purification.
| S-EPMC8388088 | biostudies-literature
Project description:We theoretically examine the drying of a stationary liquid droplet on an inclined surface. Both analytical and numerical approaches are considered, while assuming that the evaporation results from the purely diffusive transport of liquid vapor and that the contact line is a pinned circle. For the purposes of the analytical calculations, we suppose that the effect of gravity relative to the surface tension is weak, i.e. the Bond number (Bo) is small. Then, we express the shape of the drop and the vapor concentration field as perturbation expansions in terms of Bo. When the Bond number is zero, the droplet is unperturbed by the effect of gravity and takes the form of a spherical cap, for which the vapor concentration field is already known. Here, the Young-Laplace equation is solved analytically to calculate the first-order correction to the shape of the drop. Knowing the first-order perturbation to the drop geometry and the zeroth-order distribution of vapor concentration, we obtain the leading-order contribution of gravity to the rate of droplet evaporation by utilizing Green's second identity. The analytical results are supplemented by numerical calculations, where the droplet shape is first determined by minimizing the Helmholtz free energy and then the evaporation rate is computed by solving Laplace's equation for the vapor concentration field via a finite-volume method. Perhaps counter-intuitively, we find that even when the droplet deforms noticeably under the influence of gravity, the rate of evaporation remains almost unchanged, as if no gravitational effect is present. Furthermore, comparison between analytical and numerical calculations reveals that considering only the leading-order corrections to the shape of the droplet and vapor concentration distribution provides estimates that are valid well beyond their intended limit of very small Bo.
| S-EPMC6930299 | biostudies-literature
Project description:The evaporation and dynamics of a multicomponent droplet on a heated chemical patterned surface were presented. Comparing to the evaporation process of a multicomponent droplet on a homogenous surface, it is found that the chemical patterned surface can not only enhance evaporation by elongating the contact line, but also change the evaporation process from three regimes for the homogenous surface including constant contact line (CCL) regime, constant contact angle (CCA) regime and mix mode (MM) to two regimes, i.e. constant contact line (CCL) and moving contact line (MCL) regimes. The mechanism of contact line stepwise movement in MCL regimes in the microscopic range is investigated in detail. In addition, an improved local force model on the contact line was employed for analyzing the critical receding contact angles on homogenous and patterned surfaces. The analysis results agree well for both surfaces, and confirm that the transition from CCL to MCL regimes indicated droplet composition changes from multicomponent to monocomponent, providing an important metric to predict and control the dynamic behavior and composition of a multicomponent droplet using a patterned surface.
| S-EPMC5291323 | biostudies-literature
Project description:The deposit patterns derived from droplet evaporation allow current development of medical tests and new strategies for diagnostic in patients. For such purpose, the development and implementation of algorithms capable of characterizing and differentiating deposits are crucial elements. We report the study of deposit patterns formed by the droplet evaporation of binary mixtures of proteins containing NaCl. Optical microscopy reveals aggregates such as tip arrow-shaped, dendritic and semi-rosette patterns, needle-like and scalloped lines structures, as well as star-like and prism-shaped salt crystals. We use the first-order statistics (FOS) and gray level co-occurrence matrix (GLCM) to characterize the complex texture of deposit patterns. Three significant findings arise from this analysis: first, the FOS and GLCM parameters structurally characterize protein deposits. Secondly, they conform to simple exponential laws that change as a function of the NaCl concentration. Finally, the parameters are capable of revealing the different structural changes that occur during the droplet evaporation.
| S-EPMC6018122 | biostudies-literature
Project description:Studies of liquid evaporation on a solid surface are useful for wettability phenomena-related research, and can be applied in a series of scientific and industrial areas. However, traditional methods are not easy to be intergrated into small size to monitor evaporation process of a micro-droplet. In this paper, a micro-electrode array was used to measure the impedance of an electrolyte droplet, indicating the dynamic process of evaporation. This method uses the relationship between concentration and conductivity of the water solution to dynamically monitor the evaporation process. The dynamic impedance results were compared to weight and imaging data of droplet evaporation and demonstrate high correlation coefficient of the earlier 90% part of the sodium chloride droplet evaporation process (R 2 = 0.99). Our study proved that the height of the droplet will affect the impedance sensing result, and the solution used for droplet evaporation can be expanded to mixture of strong electrolyte solution such as phosphate buffered solution. Then the "impedance imaging" of the array monitored the evaporating speed differences of different sites of a sessile droplet. As the electrode array can be integrated into small size, this method is compatible for many other experimental systems and can be further used for evaporation studies and corresponding application areas.
| S-EPMC9079842 | biostudies-literature
Project description:I use a mechanical model of a soft body to study the dynamics of an individual fluid droplet in a random, non-wettable porous medium. The model of droplet relies on the spring–mass system with pressure. I run hundreds of independent simulations. I average droplets trajectories and calculate the averaged tortuosity of the porous domain. Results show that porous media tortuosity increases with decreasing porosity, similar to single-phase fluid study, but the form of this relationship is different. Supplementary Information The online version contains supplementary material available at 10.1007/s11242-021-01705-z.
| S-EPMC8546388 | biostudies-literature
Project description:Omniphobic surfaces with reentrant microstructures have been investigated for a range of applications, but the evaporation of high- and low-surface-tension liquid droplets placed on such surfaces has not been rigorously studied. In this work, we develop a technique to fabricate omniphobic surfaces on copper substrates to allow for a systematic examination of the effects of surface topography on the evaporation dynamics of water and ethanol droplets. Compared to a water droplet, the ethanol droplet not only evaporates faster, but also inhibits Cassie-to-Wenzel wetting transitions on surfaces with certain geometries. We use an interfacial energy-based description of the system, including the transition energy barrier and triple line energy, to explain the underlying transition mechanism and behaviour observed. Suppression of the wetting transition during evaporation of droplets provides an important metric for evaluating the robustness of omniphobic surfaces requiring such functionality.
| S-EPMC4658527 | biostudies-literature
Project description:Assessment of bone loss and osteoporosis by ultrasound systems is based on the speed of sound and broadband ultrasound attenuation of a single wave. However, the existence of a second wave in cancellous bone has been reported and its existence is an unequivocal signature of poroelastic media. To account for the fact that ultrasound is sensitive to microarchitecture as well as bone mineral density (BMD), a fabric-dependent anisotropic poroelastic wave propagation theory was recently developed for pure wave modes propagating along a plane of symmetry in an anisotropic medium. Key to this development was the inclusion of the fabric tensor--a quantitative stereological measure of the degree of structural anisotropy of bone--into the linear poroelasticity theory. In the present study, this framework is extended to the propagation of mixed wave modes along an arbitrary direction in anisotropic porous media called quasi-waves. It was found that differences between phase and group velocities are due to the anisotropy of the bone microarchitecture, and that the experimental wave velocities are more accurately predicted by the poroelastic model when the fabric tensor variable is taken into account. This poroelastic wave propagation theory represents an alternative for bone quality assessment beyond BMD.
| S-EPMC3115277 | biostudies-other
Project description:Compared with previous textiles possessing a hierarchical roughness structure for accelerating moisture evaporation, the use of Joule-heating to prepare heatable textiles is a more novel and useful way to achieve ultra-fast evaporation. Herein, we report an assembly strategy to create a functional non-woven (NW) fabric for directional moisture transportation and ultra-fast evaporation, ameliorating previous shortcomings. The resulting functional NW fabric reaches a sheet resistance of 1.116 Ω □-1, and the increased surface temperature (76.1 °C) induced by a low voltage (5 V) further results in an excellent ultra-fast evaporation rate (3.42 g h-1). Also, the moisture is transported to the outer surface of the designed fabric and spreads onto this surface. This desirable property can expand the contact area between sweat and the heatable fabric, further improving the evaporation efficiency, while maintaining the dry state of human skin. Generally, this functional textile with remarkable moisture management capabilities could be applied in winter outdoor sportswear to maintain human comfort.
| S-EPMC9055594 | biostudies-literature
Project description:The dielectric constants of nylon fabrics saturated with aqueous NaCl solutions, Fabric-Superdielectric Materials (F-SDM), were measured to be >10⁵ even at the shortest discharge times (>0.001 s) for which reliable data could be obtained using the constant current method, thus demonstrating the existence of a third class of SDM. Hence, the present results support the general theoretical SDM hypothesis, which is also supported by earlier experimental work with powder and anodized foil matrices: Any material composed of liquid containing dissolved, mobile ions, confined in an electrically insulating matrix, will have a very high dielectric constant. Five capacitors, each composed of a different number of layers of salt solution saturated nylon fabric, were studied, using a galvanostat operated in constant current mode. Capacitance, dielectric constant, energy density and power density as a function of discharge time, for discharge times from ~100 s to nearly 0.001 s were recorded. The roll-off rate of the first three parameters was found to be nearly identical for all five capacitors tested. The power density increased in all cases with decreasing discharge time, but again the observed frequency response was nearly identical for all five capacitors. Operational limitations found for F-SDM are the same as those for other aqueous solution SDM, particularly a low maximum operating voltage (~2.3 V), and dielectric "constants" that are a function of voltage, decreasing for voltages higher than ~0.8 V. Extrapolations of the present data set suggest F-SDM could be the key to inexpensive, high energy density (>75 J/cm³) capacitors.
| S-EPMC5457209 | biostudies-other