Browse
Submit Data
Databases
API
Help

Dataset Information

20 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

The Influence of the Processing Parameters on the Laser-Ablation of Stainless Steel and Brass during the Engraving by Nanosecond Fiber Laser.

ABSTRACT: In this paper, we investigate the influence of the following parameters: pulse duration, pulse repetition rate, line-to-line and pulse-to-pulse overlaps, and scanning strategy on the ablation of AISI 316L steel and CuZn37 brass with a nanosecond, 1064-nm, Yb fiber laser. The results show that the material removal rate (MRR) increases monotonically with pulse duration up to the characteristic repetition rate (f₀) where pulse energy and average power are maximal. The maximum MRR is reached at a repetition rate that is equal or slightly higher as f₀. The exact value depends on the correlation between the fluence of the laser pulses and the pulse repetition rate, as well as on the material properties of the sample. The results show that shielding of the laser beam by plasma and ejected material plays an important role in reducing the MRR. The surface roughness is mainly influenced by the line-to-line and the pulse-to-pulse overlaps, where larger overlap leads to lower roughness. Process optimization indicates that while operating with laser processing parameters resulting in the highest MRR, the best ratio between the MRR and surface roughness appears at ~50% overlap of the laser pulses, regardless of the material being processed.

SUBMITTER: Hribar L

PROVIDER: S-EPMC8779350 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Nanosecond laser coloration on stainless steel surface.

Project description:In this work, we present laser coloration on 304 stainless steel using nanosecond laser. Surface modifications are tuned by adjusting laser parameters of scanning speed, repetition rate, and pulse width. A comprehensive study of the physical mechanism leading to the appearance is presented. Microscopic patterns are measured and employed as input to simulate light-matter interferences, while chemical states and crystal structures of composites to figure out intrinsic colors. Quantitative analysis clarifies the final colors and RGB values are the combinations of structural colors and intrinsic colors from the oxidized pigments, with the latter dominating. Therefore, the engineering and scientific insights of nanosecond laser coloration highlight large-scale utilization of the present route for colorful and resistant steels.

| S-EPMC5541041 | biostudies-literature

Long-Term Influence of Laser-Processing Parameters on (Super)hydrophobicity Development and Stability of Stainless-Steel Surfaces.

Project description:Controlling the surface wettability represents an important challenge in the field of surface functionalization. Here, the wettability of a stainless-steel surface is modified by 30-ns pulses of a Nd:YAG marking laser (? = 1064 nm) with peak fluences within the range 3.3?25.1 J cm-2. The short- (40 days), intermediate- (100 days) and long-term (1 year) superhydrophilic-to-(super)hydrophobic transition of the laser-textured surfaces exposed to the atmospheric air is examined by evaluating its wettability in the context of the following parameters: (i) pulse fluence; (ii) scan line separation; (iii) focal position and (iv) wetting period due to contact angle measurements. The results show that using solely a short-term evaluation can lead to wrong conclusions and that the faster development of the hydrophobicity immediately after laser texturing usually leads to lower final contact angle and vice versa, the slower this transition is, the more superhydrophobic the surface is expected to become (possibly even with self-cleaning ability). Depending on laser fluence, the laser-textured surfaces can develop stable or unstable hydrophobicity. Stable hydrophobicity is achieved, if the threshold fluence of 12 J cm-2 is exceeded. We show that by nanosecond-laser texturing a lotus-leaf-like surface with a contact angle above 150° and roll-off angle below 5° can be achieved.

| S-EPMC6266256 | biostudies-literature

Femtosecond Laser Engraving of Deep Patterns in Steel and Sapphire.

Project description:Femtosecond laser engraving offers appealing advantages compared to regular laser engraving such as higher precision and versatility. In particular, the inscription of deep patterns exhibits an increasing interest in industry. In this work, an optimization protocol based on constraining overlap ratio and scan number is demonstrated. The proposed method allows changing overlap ratio while maintaining depth in the same range, which reduces the sampling number. This study WAS applied to stainless steel 316 L and sapphire for engravings deeper than 100 μm. Results exhibit overall depths higher than threshold values and allowed to determine optimized engraving quality, for instance, roughness in steel can be reduced while maintaining depth and taper angle by reducing overlap ratio. The optimized laser parameters such as roughness and taper angle factors for sapphire were also found to be as follows: 200 kHz, 86% overlap and 12 J/cm2. As a demonstration, a logo engraving is illustrated at the end.

| S-EPMC8306761 | biostudies-literature

Wettability and friction control of a stainless steel surface by combining nanosecond laser texturing and adsorption of superhydrophobic nanosilica particles.

Project description:In this work, we present functionalization of AISI 316?L surfaces by nanosecond Nd:YAG laser texturing and adsorption of superhydrophobic fluoroalkylsilane functionalized 30-nm silica nanoparticles. Surface modification by varying the distance between laser-produced micro(?)-channels leads to different surface roughnesses. After nanosilica coating, the superhydrophilic laser-textured surfaces change into superhydrophobic surfaces with the same ?-roughness. A higher ?-channel density leads to more hydrophobic surfaces after coating. This enables a study of the combined effect of surface wettability and morphology on the friction coefficient and wear resistance. Experiments were performed in dry and water environments. In the case of dry friction, increased ?-roughness leads to a higher friction coefficient, and the water-repellency modification by nanosilica particles has no influence on the tribological behaviour. In contrast, in the water environment, the wettability presents an important contribution to the properties of contact surfaces: hydrophobic surfaces exhibit a lower friction coefficient, especially at higher densities of ?-channels. Energy-dispersive X-ray spectroscopy analysis of surfaces before and after the tribological experiments is performed, revealing the difference in weight % of Si in the worn surface compared to the unworn surface, which varies according to the nature of the surface morphology due to laser texturing in both dry and water environments.

| S-EPMC5945667 | biostudies-literature

Nanosecond Laser Fabrication of Hydrophobic Stainless Steel Surfaces: The Impact on Microstructure and Corrosion Resistance.

Project description:Creation of hydrophobic and superhydrophobic surfaces has attracted broad attention as a promising solution for protection of metal surfaces from corrosive environments. This work investigates the capability of nanosecond fiber laser surface texturing followed by a low energy coating in the fabrication of hydrophobic 17-4 PH stainless steel surfaces as an alternative to the ultrashort lasers previously utilized for hydrophobic surfaces production. Laser texturing of the surface followed by applying the hydrophobic coating resulted in steady-state contact angles of up to 145°, while the non-textured coated base metal exhibited the contact angle of 121°. The microstructure and compositional analysis results confirmed that the laser texturing process neither affects the microstructure of the base metal nor causes elemental loss from the melted regions during the ultrafast melting process. However, the electrochemical measurements demonstrated that the water-repelling property of the surface did not contribute to the anticorrosion capability of the substrate. The resultant higher corrosion current density, lower corrosion potential, and higher corrosion rate of the laser textured surfaces were ascribed to the size of fabricated surface micro-grooves, which cannot retain the entrapped air inside the hierarchical structure when fully immersed in a corrosive medium, thus degrading the material's corrosion performance.

| S-EPMC6163166 | biostudies-other

Mouse Lung Response to Stainless Steel and Mild Steel Welding Fume

Project description:A/J mice are genetically predisposed to spontaneous and/or chemically-induced lung tumors while C57BL/6J (B6) mice are resistant. This genetic disparity provides a unique scenario to identify molecular mechanisms associated with the lung response to welding fume at the transcriptome level.

2010-04-30 | GSE20174 | GEO

Characterization of a Laser Surface-Treated Martensitic Stainless Steel.

Project description:Laser surface treatment was carried out on AISI 416 machinable martensitic stainless steel containing 0.225 wt.% sulfur. Nd:YAG laser with a 2.2-KW continuous wave was used. The aim was to compare the physical and chemical properties achieved by this type of selective surface treatment with those achieved by the conventional treatment. Laser power of different values (700 and 1000 W) with four corresponding different laser scanning speeds (0.5, 1, 2, and 3 m•min-1) was adopted to reach the optimum conditions for impact toughness, wear, and corrosion resistance for laser heat treated (LHT) samples. The 0 °C impact energy of LHT samples indicated higher values compared to the conventionally heat treated (CHT) samples. This was accompanied by the formation of a hard surface layer and a soft interior base metal. Microhardness was studied to determine the variation of hardness values with respect to the depth under the treated surface. The wear resistance at the surface was enhanced considerably. Microstructure examination was characterized using optical and scanning electron microscopes. The corrosion behavior of the LHT samples was also studied and its correlation with the microstructures was determined. The corrosion data was obtained in 3.5% NaCl solution at room temperature by means of a potentiodynamic polarization technique.

| S-EPMC5553412 | biostudies-other

Electrolytic plasma processing-an innovative treatment for surface modification of 304 stainless steel.

Project description:There is widespread attention to surface profile and modification of 304 stainless steel for research development and application. Here, a successful electrolytic plasma processing (EPP) technique has been developed for both surface pretreatment and coating deposition of 304 stainless steel. Representative images confirm that the number of the pits increases and the ravines gradually disappear on the steel pretreated by EPP with the increase of processing time and applied voltage. Moreover, there is an obvious enhancement in surface roughness of 304 stainless steel after EPP pretreatment. In the case of coating deposition, the further EPP modification conducted on the pretreated sample offers a simple and effective technique for the production of zinc coatings having the features of full coverage and homogeneous distribution. The results show that a zinc coating with a thickness of approximately 0.5 μm can be obtained on the 304 stainless steel by means of EPP for only 60 s.

| S-EPMC5428051 | biostudies-literature

From Femtosecond to Nanosecond Laser Microstructuring of Conical Aluminum Surfaces by Reactive Gas Assisted Laser Ablation.

Project description:A conical microstructure is one of the most versatile surface textures obtained by ultrashort laser micromachining. Besides an increased surface area, unique surface properties such as superhydrophilicity, increased absorptivity; and thermal emissivity can be tailored. On metals, usually ultrashort laser pulses in the femtosecond to low picosecond range are used to obtain these surface structures, whereas nanosecond laser pulses favor melting processes. Herein, we report on an investigation of reactive gas atmospheres such as oxygen, steam, and halogens during laser micromachining of aluminum with 6 ns laser pulses. At a reduced pressure of 20 hPa (air) with additional iodine vapor as reactive species, we found a perfectly microconical structured surface to be formed with nanosecond laser pulses. The resulting surface structures were proven to be free of residual halogens. The application of nanosecond instead of femtosecond laser pulses for the surface structuring process allows to apply significantly less complex laser sources.

| S-EPMC7496992 | biostudies-literature

The Influence of the Structure Parameters on the Mechanical Properties of Cylindrically Mapped Gyroid TPMS Fabricated by Selective Laser Melting with 316L Stainless Steel Powder.

Project description:The development of additive manufacturing techniques has made it possible to produce porous structures with complex geometry with unique properties as potential candidates for energy absorption, heat dissipation, biomedical, and vibration control application. Recently, there has been increased interest in additively manufacturing porous structures based on triply periodic minimal surfaces (TPMS) topology. In this paper, the mechanical properties and energy absorption abilities of cylindrical mapped TPMS structures with shell gyroid unit cells fabricated by selective laser melting (SLM) with 316L stainless steel under compression loading were investigated. Based on the experimental study, it was found that tested structures exhibited two different deformation modes. There is also a relationship between the number and shapes of unit cells in the structure and the elastic modulus, yield strength, plateau stress, and energy absorption. These results can be used to design and manufacture more efficient lightweight parts lattices for energy absorbing applications, e.g., in the field of biomedical and bumpers applications. The deformation mode for each tested sample was also presented on the records obtained from the ARAMIS system.

| S-EPMC9229397 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data