Design and Fabrication of Pneumatically Actuated Valveless Pumps.
Ontology highlight
ABSTRACT:
SUBMITTER: Lin JL
PROVIDER: S-EPMC8780249 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Bubble actuated micro-pumps have great potential to be integrated into microfluidic systems to allow the independence of peripheral equipment. Previous studies on bubble actuated valveless micro-pumps have been mainly limited to experimental studies and numerical simulations due to the complex behavior of bubbles. In this paper, the construction of a mathematical model for a bubble actuated valveless micro-pump considering fluid dynamics, heat and mass transfer and bubble dynamics is described. A prototype was fabricated and tested to verify this theoretical model. The morphological evolution of the driving bubbles during the heating process was observed by a high-speed charge-coupled device (CCD) camera, the flow rate produced by the micro-pump under different working conditions was recorded and the test results were explained by the heat dissipation model. The model in this study was able to precisely predict the flow of micro-pumps in different drive modes. The principle behind defining the heating frequency and the duty cycle based on the pump chamber volume was determined. The study shows the mechanism of bubble controlling and the good prospects of bubble actuated valveless micro-pumps.
| S-EPMC6187526 | biostudies-literature
Project description:We describe a microfluidic device with an integrated nanochannel array to trap individual bacteria and monitor growth and reproduction of lineages over multiple generations. Our poly(dimethylsiloxane) device comprises a pneumatically actuated nanochannel array that includes 1280 channels with widths from 600 to 1000 nm to actively trap diverse bacteria. Integrated pumps and valves perform on-chip fluid and cell manipulations that provide dynamic control of cell loading and nutrient flow, permitting chemostatic growth for extended periods of time (typically 12 to 20 h). Nanochannels confine bacterial growth to a single dimension, facilitating high-resolution, time-lapse imaging and tracking of individual cells. We use the device to monitor the growth of single bacterial cells that undergo symmetric (Bacillus subtilis) and asymmetric (Caulobacter crescentus) division and reconstruct their lineages to correlate growth measurements through time and among related cells. Furthermore, we monitor the motility state of single B. subtilis cells across multiple generations by the expression of a fluorescent reporter protein and observe that the state of the epigenetic switch is correlated over five generations. Our device allows imaging of cellular lineages with high spatiotemporal resolution to facilitate the analysis of biological processes spanning multiple generations.
| S-EPMC5073376 | biostudies-literature
Project description:We propose a new class of magnetically actuated pumps and valves that could be incorporated into microfluidic chips with no further external connections. The idea is to repurpose ferromagnetic low Reynolds number swimmers as devices capable of generating fluid flow, by restricting the swimmers' translational degrees of freedom. We experimentally investigate the flow structure generated by a pinned swimmer in different scenarios, such as unrestricted flow around it as well as flow generated in straight, cross-shaped, Y-shaped and circular channels. This demonstrates the feasibility of incorporating the device into a channel and its capability of acting as a pump, valve and flow splitter. Different regimes could be selected by tuning the frequency and amplitude of the external magnetic field driving the swimmer, or by changing the channel orientation with respect to the field. This versatility endows the device with varied functionality which, together with the robust remote control and reproducibility, makes it a promising candidate for several applications.
| S-EPMC5772482 | biostudies-literature
Project description:Thermal bubble-driven micro-pumps are an upcoming actuation technology that can be directly integrated into micro/mesofluidic channels to displace fluid without any moving parts. These pumps consist of high power micro-resistors, which we term thermal micro-pump (TMP) resistors, that locally boil fluid at the resistor surface in microseconds creating a vapor bubble to perform mechanical work. Conventional fabrication approaches of thermal bubble-driven micro-pumps and associated microfluidics have utilized semiconductor micro-fabrication techniques requiring expensive tooling with long turn around times on the order of weeks to months. In this study, we present a low-cost approach to rapidly fabricate and test thermal bubble-driven micro-pumps with associated microfluidics utilizing commercial substrates (indium tin oxide, ITO, and fluorine doped tin oxide, FTO, coated glass) and tooling (laser cutter). The presented fabrication approach greatly reduces the turn around time from weeks/months for conventional micro-fabrication to a matter of hours/days allowing acceleration of thermal bubble-driven micro-pump research and development (R&D) learning cycles.
| S-EPMC9610814 | biostudies-literature
Project description:This paper describes the computationally informed design and experimental validation of a microfluidic chip device with multi-axial stretching capabilities. The device, based on PDMS soft-lithography, consisted of a thin porous membrane, mounted between two fluidic compartments, and tensioned via a set of vacuum-driven actuators. A finite element analysis solver implementing a set of different nonlinear elastic and hyperelastic material models was used to drive the design and optimization of chip geometry and to investigate the resulting deformation patterns under multi-axial loading. Computational results were cross-validated by experimental testing of prototypal devices featuring the in silico optimized geometry. The proposed methodology represents a suite of computationally handy simulation tools that might find application in the design and in silico mechanical characterization of a wide range of stretchable microfluidic devices.
| S-EPMC5511244 | biostudies-literature
Project description:A major difficulty in applying computational design methods to nanophotonic devices is ensuring that the resulting designs are fabricable. Here, we describe a general inverse design algorithm for nanophotonic devices that directly incorporates fabrication constraints. To demonstrate the capabilities of our method, we designed a spatial-mode demultiplexer, wavelength demultiplexer, and directional coupler. We also designed and experimentally demonstrated a compact, broadband 1 × 3 power splitter on a silicon photonics platform. The splitter has a footprint of only 3.8 × 2.5 μm, and is well within the design rules of a typical silicon photonics process, with a minimum radius of curvature of 100 nm. Averaged over the designed wavelength range of 1400-1700 nm, our splitter has a measured insertion loss of 0.642 ± 0.057 dB and power uniformity of 0.641 ± 0.054 dB.
| S-EPMC5431915 | biostudies-literature
Project description:The paper presents an MRI-compatible neurosurgical robotic system that is designed to operate the head-mounted meso-scale 6-degree-of-freedom (DoF) spring-based MINIR-II. The robotic system consists of an actuation module, a transmission module, and the robot module. The transmission module consist of a switching mechanism for reducing the required number of motors by half, an innovative linkage mechanism to insert and retract the robot with minimal tendon displacement and friction loss, and a quick-connect mechanism for easy attachment of the disposable MINIR-II. Design, analysis, and development of each module are described in detail. Most of the critical components such as the robot, the quick-connect, the linkage mechanism, and various gear-pulley combinations in our design are 3-D printed. Preliminary mechanical properties characterization of the system and the capability of the underactuated system to replicate the critical functions of the 6-DoF robot are presented. The robot motion capability in a brain phantom model and its MRI compatibility in a 7-Tesla magnet were verified.
| S-EPMC6205204 | biostudies-literature
Project description:Nanogap electrodes consist of pairs of electrically conducting tips that exhibit nanoscale gaps. They are building blocks for a variety of applications in quantum electronics, nanophotonics, plasmonics, nanopore sequencing, molecular electronics, and molecular sensing. Crack-junctions (CJs) constitute a new class of nanogap electrodes that are formed by controlled fracture of suspended bridge structures fabricated in an electrically conducting thin film under residual tensile stress. Key advantages of the CJ methodology over alternative technologies are that CJs can be fabricated with wafer-scale processes, and that the width of each individual nanogap can be precisely controlled in a range from <2 to >100 nm. While the realization of CJs has been demonstrated in initial experiments, the impact of the different design parameters on the resulting CJs has not yet been studied. Here we investigate the influence of design parameters such as the dimensions and shape of the notches, the length of the electrode-bridge and the design of the anchors, on the formation and propagation of cracks and on the resulting features of the CJs. We verify that the design criteria yields accurate prediction of crack formation in electrode-bridges featuring a beam width of 280 nm and beam lengths ranging from 1 to 1.8 μm. We further present design as well as experimental guidelines for the fabrication of CJs and propose an approach to initiate crack formation after release etching of the suspended electrode-bridge, thereby enabling the realization of CJs with pristine electrode surfaces.
| S-EPMC6444981 | biostudies-literature
Project description:Pumps are critical life-sustaining components for all animals. At the earliest stages of life, the tubular embryonic heart works as a valveless pump capable of generating unidirectional blood flow. Inspired by this elementary pump, we developed an example of a biohybrid valveless pump-bot powered by engineered skeletal muscle. Our pump-bot consists of a soft hydrogel tube connected at both ends to a stiffer polydimethylsiloxane (PDMS) scaffold, creating an impedance mismatch. A contractile muscle ring wraps around the hydrogel tube at an off-center location, squeezing the tube with or without buckling it locally. Cyclic muscle contractions, spontaneous or electrically stimulated, further squeeze the tube, resulting in elastic waves that propagate along the soft tube and get reflected back at the soft/stiff tube boundaries. Asymmetric placement of muscle ring results in a time delay between the wave arrivals, thus establishing a net unidirectional fluid flow irrespective of whether the tube is buckled or not. Flow rates of up to 22.5 μL/min are achieved by the present pump-bot, which are at least three orders of magnitude higher than those from cardiomyocyte-powered valve pumps of similar size. Owning to its simple geometry, robustness, ease of fabrication, and high pumping performance, our pump-bot is particularly well-suited for a wide range of biomedical applications in microfluidics, drug delivery, biomedical devices, cardiovascular pumping system, and more.
| S-EPMC6358718 | biostudies-literature
Project description:Inverse design methods produce nanophotonic devices with arbitrary geometries that show high efficiencies as well as novel functionalities. Ensuring fabricability during optimization of these unrestricted device geometries is a major challenge for these design methods. In this work, we construct a fabrication constraint penalty function for level set geometry representations of these devices. This analytical penalty function limits both the gap size and boundary curvature of a device. We incorporate this penalty in a fully automated optical design flow using a quasi-Newton optimization method. The performance of our design method is evaluated by designing a series of waveguide demultiplexers (WDM) and mode converters with various footprints and minimum feature sizes. Finally, we design and experimentally characterize three WDMs with a 80 nm, 120 nm and 160 nm feature size.
| S-EPMC6588594 | biostudies-literature