Browse
Submit Data
Databases
API
Help

Dataset Information

15 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Facile Fabrication of ZnO-ZnFe₂O₄ Hollow Nanostructure by a One-Needle Syringe Electrospinning Method for a High-Selective H₂S Gas Sensor.

ABSTRACT: Herein, a facile fabrication process of ZnO-ZnFe₂O₄ hollow nanofibers through one-needle syringe electrospinning and the following calcination process is presented. The various compositions of the ZnO-ZnFe₂O₄ nanofibers are simply created by controlling the metal precursor ratios of Zn and Fe. Moreover, the different diffusion rates of the metal oxides and metal precursors generate a hollow nanostructure during calcination. The hollow structure of the ZnO-ZnFe₂O₄ enables an enlarged surface area and increased gas sensing sites. In addition, the interface of ZnO and ZnFe₂O₄ forms a p-n junction to improve gas response and to lower operation temperature. The optimized ZnO-ZnFe₂O₄ has shown good H₂S gas sensing properties of 84.5 (S = R_a/R_g) at 10 ppm at 250 °C with excellent selectivity. This study shows the good potential of p-n junction ZnO-ZnFe₂O₄ on H₂S detection and affords a promising sensor design for a high-performance gas sensor.

SUBMITTER: Park KR

PROVIDER: S-EPMC8782020 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Facile fabrication of Mn2+-doped ZnO photocatalysts by electrospinning.

Project description:In this study, a high-efficiency photocatalyst was synthesized by Mn2+-doped ZnO nanofibres (NFs) fabricated by facile electrospinning and a following annealing process, in which Mn2+ successes incorporate to ZnO NFs lattice without changing any morphology and crystalline structure of ZnO. The photodegradation properties of ZnO loading with different concentrations of Mn2+ (5, 10, 15 and 50 at%) were investigated. The 50% MnO-ZnO composite owns excellent active photocatalytic performance (quantum efficiency up to 7.57%) compared to pure ZnO (0.16%) under visible light and can be considered as an efficient visible light photocatalyst material. We systematically analysed its catalytic mechanism and found that the enhancement belongs to the Mn doping effect and the phase junction between MnO and ZnO. The dominant mechanism of Mn doping leads to the presence of impurity levels in the band gap of ZnO, narrowing the optical band gap of ZnO. In addition, doped Mn2+ ions can be used as electron traps that inhibit the recombination process and promote electron-hole pair separation. In summary, this paper provides a convenient method for fabricating highly efficient visible light photocatalysts using controlled annealing.

| S-EPMC7211861 | biostudies-literature

SiO2/ZnO Composite Hollow Sub-Micron Fibers: Fabrication from Facile Single Capillary Electrospinning and Their Photoluminescence Properties.

Project description:In this work, SiO2/ZnO composite hollow sub-micron fibers were fabricated by a facile single capillary electrospinning technique followed by calcination, using tetraethyl orthosilicate (TEOS), polyvinylpyrrolidone (PVP) and ZnO nanoparticles as raw materials. The characterization results of the scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR) spectra indicated that the asprepared composite hollow fibers consisted of amorphous SiO2 and hexagonal wurtzite ZnO. The products revealed uniform tubular structure with outer diameters of 400-500 nm and wall thickness of 50-60 nm. The gases generated and the directional escaped mechanism was proposed to illustrate the formation of SiO2/ZnO composite hollow sub-micron fibers. Furthermore, a broad blue emission band was observed in the photoluminescence (PL) of SiO2/ZnO composite hollow sub-micron fibers, exhibiting great potential applications as blue light-emitting candidate materials.

| S-EPMC5388155 | biostudies-literature

Syringe and needle size, syringe type, vacuum generation, and needle control in aspiration procedures.

Project description:Syringes are used for diagnostic fluid aspiration and fine-needle aspiration biopsy in interventional procedures. We determined the benefits, disadvantages, and patient safety implications of syringe and needle size on vacuum generation, hand force requirements, biopsy/fluid yield, and needle control during aspiration procedures.Different sizes (1, 3, 5, 10, and 20 ml) of the conventional syringe and aspirating mechanical safety syringe, the reciprocating procedure device, were studied. Twenty operators performed aspiration procedures with the following outcomes measured: (1) vacuum (torr), (2) time to vacuum (s), (3) hand force to generate vacuum (torr-cm2), (4) operator difficulty during aspiration, (5) biopsy yield (mg), and (6) operator control of the needle tip position (mm).Vacuum increased tissue biopsy yield at all needle diameters (P<0.002). Twenty-milliliter syringes achieved a vacuum of -517 torr but required far more strength to aspirate, and resulted in significant loss of needle control (P<0.002). The 10-ml syringe generated only 15% less vacuum (-435 torr) than the 20-ml device and required much less hand strength. The mechanical syringe generated identical vacuum at all syringe sizes with less hand force (P<0.002) and provided significantly enhanced needle control (P<0.002).To optimize patient safety and control of the needle, and to maximize fluid and tissue yield during aspiration procedures, a two-handed technique and the smallest syringe size adequate for the procedure should be used. If precise needle control or one-handed operation is required, a mechanical safety syringe should be considered.

| S-EPMC3638030 | biostudies-literature

Facile Fabrication of Superhydrophobic Copper- Foam and Electrospinning Polystyrene Fiber for Combinational Oil?Water Separation.

Project description:Membrane-based metal substrates with special surface wettability have been applied widely for oil/water separation. In this work, a series of copper foams with superhydrophobicity and superoleophilicity were chemically etched using 10 mg mL-1 FeCl3/HCl solution with consequent ultrasonication, followed by the subsequent modification of four sulfhydryl compounds. A water contact angle of 158° and a sliding angle lower than 5° were achieved for the copper foam modified using 10 mM n-octadecanethiol solution in ethanol. In addition, the interaction mechanism was initially investigated, indicating the coordination between copper atoms with vacant orbital and sulfur atoms with lone pair electrons. In addition, the polymeric fibers were electrospun through the dissolution of polystyrene in a good solvent of chlorobenzene, and a nonsolvent of dimethyl sulfoxide. Oil absorption and collection over the water surface were carried out by the miniature boat made out of copper foam, a string bag of as-spun PS fibers with high oil absorption capacity, or the porous boat embedded with the as-spun fibers, respectively. The findings might provide a simple and practical combinational method for the solution of oil spill.

| S-EPMC6402002 | biostudies-literature

Facile Hydrothermal Fabrication of Nano-Oxide Hollow Spheres using Monosaccharides as Sacrificial Templates.

Project description: Not available

| S-EPMC4380956 | biostudies-literature

Interior-architectured ZnO nanostructure for enhanced electrical conductivity via stepwise fabrication process.

Project description:Fabrication of ZnO nanostructure via direct patterning based on sol-gel process has advantages of low-cost, vacuum-free, and rapid process and producibility on flexible or non-uniform substrates. Recently, it has been applied in light-emitting devices and advanced nanopatterning. However, application as an electrically conducting layer processed at low temperature has been limited by its high resistivity due to interior structure. In this paper, we report interior-architecturing of sol-gel-based ZnO nanostructure for the enhanced electrical conductivity. Stepwise fabrication process combining the nanoimprint lithography (NIL) process with an additional growth process was newly applied. Changes in morphology, interior structure, and electrical characteristics of the fabricated ZnO nanolines were analyzed. It was shown that filling structural voids in ZnO nanolines with nanocrystalline ZnO contributed to reducing electrical resistivity. Both rigid and flexible substrates were adopted for the device implementation, and the robustness of ZnO nanostructure on flexible substrate was verified. Interior-architecturing of ZnO nanostructure lends itself well to the tunability of morphological, electrical, and optical characteristics of nanopatterned inorganic materials with the large-area, low-cost, and low-temperature producibility.

| S-EPMC4165434 | biostudies-other

Facile fabrication of self-assembled ZnO nanowire network channels and its gate-controlled UV detection.

Project description:We demonstrate a facile way to fabricate an array of gate-controllable UV sensors based on assembled zinc oxide nanowire (ZnO NW) network field-effect transistor (FET). This was realized by combining both molecular surface programmed patterning and selective NW assembly on the polar regions avoiding the nonpolar regions, followed by heat treatment at 300 °C to ensure stable contact between NWs. The ZnO NW network FET devices showed typical n-type characteristic with an on-off ratio of 105, transconductance around 47 nS, and mobility around 0.175 cm2 V-?1 s-?1. In addition, the devices showed photoresponsive behavior to UV light that can be controlled by the applied gate voltage. The photoresponsivity was found to be linearly proportional to the channel voltage Vds, showing maximum photoresponsivity at Vds?=?7 V.

| S-EPMC6305260 | biostudies-literature

A Facile and Flexible Approach for Large-Scale Fabrication of ZnO Nanowire Film and Its Photocatalytic Applications.

Project description:A novel strategy for large-scale synthesis of ZnO nanowire film is reported, which inherits the advantages of the solution-phase method and seeded growth process, such as low-temperature, efficient, economical, facile and flexible. It is easy to implement on various metals through room-temperature electrodeposition, followed by hydrothermal treatment at 90 °C, and suitable for industrialized production. The ZnO nanowires with an average wire diameter about 40 nm are in situ grown from and on nanocrystalline zinc coating, which forms a strong metallurgical bonding with the substrates. The p-type ZnO nanowire film has a well-preferred orientation along the (100) direction and a wurtzite structure, thereby displaying an effective photocatalytic capability for carcinogenic Cr6+ ions and CO2 greenhouse gas reduction under visible light irradiation. In addition to these features, the ZnO nanowire film is easy to recycle and, therefore, it has broad application prospects in contaminant degradation and renewable energy.

| S-EPMC6630657 | biostudies-literature

Syringeless Electrospinning toward Versatile Fabrication of Nanofiber Web.

Project description:Although electrospinning is considered a powerful and generic tool for the preparation of nanofiber webs, several issues still need to be overcome for real-world applications. Most of these issues stem from the use of a syringe-based system, where the key factor influencing successful electrospinning is the maintenance of several subtle balances such as those of between the mass and the electrical state. It is extremely difficult to maintain these balances throughout the spinning process until all the polymeric solution in the syringe has been consumed. To overcome these limitations, we have developed a syringeless electrospinning technique as an alternative and efficient means of preparing a nanofiber web. This new technique uses a helically probed rotating cylinder. This technique can not only cover conventional methods, but also provides several advantages over syringe-based and needless electrospinning in terms of productivity (6 times higher) and processibility. For example, we can produce nanofibers with highly crystalline polymers and nanofiber-webs comprising networks of several different polymers, which is sometimes difficult in conventional electrospinning. In addition, this method provides several benefits for colloidal electrospinning as well. This method should help expand the range of applications for electrospun nanofiber webs in the near future.

| S-EPMC5264178 | biostudies-literature

Fabrication of supramolecular cyclodextrin-fullerene nonwovens by electrospinning.

Project description:Direct electrospinning of small molecules has great potential to fabricate a new class of fiber materials because this approach realizes the creation of various functional materials through the numerous molecular combinations. In this paper, we demonstrate a proof-of-concept to fabricate supramolecular fiber materials composed of cyclodextrin (CD)-fullerene inclusion complexes by electrospinning. Similar to the molecular state of fullerenes in solution, the resulting fibers include molecularly-dispersed fullerenes. We believe such a concept could be expanded to diverse host-guest complexes, opening up supramolecular solid materials science and engineering.

| S-EPMC6334797 | biostudies-literature