Heating-Induced Transformation of Anatase TiO2 Nanorods into Rock-Salt TiO Nanoparticles: Implications for Photocatalytic and Gas-Sensing Applications
Ontology highlight
ABSTRACT:
SUBMITTER: Chen X
PROVIDER: S-EPMC8805116 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Hydrogen sulfide (H2S) is a highly toxic and corrosive gas that causes a foul odor even at very low concentrations [several parts per billion (ppb)]. However, industrially discharged H2S has a concentration range of several tens of ppb to several parts per million (ppm), which conventional methods are unable to process. Therefore, advanced and sustainable methods for treating very low concentrations of H2S are urgently needed. TiO2-based photocatalysts are eco-friendly and have the ability to treat environmental pollutants, such as low-concentration gases, using light energy. However, there are no reports on H2S decomposition or oxidation at concentrations below several ppb. Therefore, in this study, we employed anatase/TiO2(B) nanotubes, which have a high specific surface area and an efficient charge-transfer interface, to treat H2S. We successfully reduced 10 ppm of H2S to 1 ppb or less at a kinetic rate of 75 μmol h-1 g-1. The suitability of our method was further demonstrated by the generation of sulfate ions and sulfur (as detected by X-ray photoelectron spectroscopy and ion chromatography), which are industrially useful as oxidation products, whereas sulfur dioxide, a harmful substance, was not produced. This is the first study to report H2S decomposition down to the ppb level, providing meaningful solutions for malodor problems and potential health hazards associated with H2S.
| S-EPMC9016837 | biostudies-literature
Project description:In this article, we demonstrate the position-controlled hydrothermal growth of rutile TiO2 nanorods using a new scanning probe lithography method in which a silicon tip, commonly used for atomic force microscopy, was pulled across an anatase TiO2 film. This process scratches the film causing tiny anatase TiO2 nanoparticles to form on the surface. According to previous reports, these anatase particles convert into rutile nanocrystals and provide the growth of rutile TiO2 nanorods in well-defined areas. Due to the small tip radius, the resolution of this method is excellent and the method is quite inexpensive compared to electron-beam lithography and similar methods providing a position-controlled growth of semiconducting TiO2 nanostructures.
| S-EPMC6369993 | biostudies-literature
Project description:Mesoporous TiO2 films with enhanced photocatalytic activity in both UV and visible wavelength ranges were developed through a non-conventional atomic layer deposition (ALD) process at room temperature. Deposition at such a low temperature promotes the accumulation of by-products in the amorphous TiO2 films, caused by the incomplete hydrolysis of the TiCl4 precursor. The additional thermal annealing induces the fast recrystallisation of amorphous films, as well as an in situ acidic treatment of TiO2. The interplay between the deposition parameters, such as purge time, the amount of structural defects introduced and the enhancement of the photocatalytic properties from different mesoporous films clearly shows that our easily upscalable non-conventional ALD process is of great industrial interest for environmental remediation and other photocatalytic applications, such as hydrogen production.
| S-EPMC9057303 | biostudies-literature
Project description:The transformation on heating LiCoMnO4, with a spinel structure, to LiCoMnO3, with a cation-disordered rock salt structure, accompanied by loss of 25% of the oxygen, has been followed using a combination of diffraction, microscopy and spectroscopy techniques. The transformation does not proceed by a topotactic mechanism, even though the spinel and rock salt phases have a similar, cubic close-packed oxygen sublattice. Instead, the transformation passes through two stages involving, first, precipitation of Li2MnO3, leaving behind a Li-deficient, Co-rich non-stoichiometric spinel and, second, rehomogenization of the two-phase assemblage, accompanied by additional oxygen loss, to give the homogeneous rock salt final product; a combination of electron energy loss spectroscopy and X-ray absorption near edge structure analyses showed oxidation states of Co2+ and Mn3+ in LiCoMnO3. Subsolidus phase diagram determination of the Li2O-CoO x -MnO y system has established the compositional extent of spinel solid solutions at approximately 500°C.
| S-EPMC4786028 | biostudies-literature
Project description:The hydrothermal dissolution-recrystallization process is a key step in the crystal structure of titania-based nanotubes and their composition. This work systematically studies the hydrothermal conditions for directly synthesizing anatase TiO2 nanotubes (ATNTs), which have not been deeply discussed elsewhere. It has been well-known that ATNTs can be synthesized by the calcination of titanate nanotubes. Herein, we found the ATNTs can be directly synthesized by optimizing the reaction temperature and time rather than calcination of titanate nanotubes, where at each temperature, there is a range of reaction times in which ATNTs can be prepared. The effect of NaOH/TiO2 ratio and starting materials was explored, and it was found that ATNTs can be prepared only if the precursor is anatase TiO2, using rutile TiO2 leads to forming titanate nanotubes. As a result, ATNTs produced directly without calcination have excellent photocatalytic CO2 reduction than titanate nanotubes and ATNTs prepared by titanate calcination.
| S-EPMC9631917 | biostudies-literature
Project description:Multifunctional thin films which can display both photocatalytic and antibacterial activity are of great interest industrially. Here, for the first time, we have used aerosol-assisted chemical vapor deposition to deposit highly photoactive thin films of Cu-doped anatase TiO2 on glass substrates. The films displayed much enhanced photocatalytic activity relative to pure anatase and showed excellent antibacterial (vs Staphylococcus aureus and Escherichia coli) ability. Using a combination of transient absorption spectroscopy, photoluminescence measurements, and hybrid density functional theory calculations, we have gained nanoscopic insights into the improved properties of the Cu-doped TiO2 films. Our analysis has highlighted that the interactions between substitutional and interstitial Cu in the anatase lattice can explain the extended exciton lifetimes observed in the doped samples and the enhanced UV photoactivities observed.
| S-EPMC7146757 | biostudies-literature
Project description:We report a simple room-temperature synthesis route for increasing the reactivity of a TiO2 photocatalyst using a solution plasma process (SPP). Hydrogen radicals generated from the SPP chamber interact with the TiO2 photocatalyst feedstock, transforming its crystalline phase and introducing oxygen vacancy defects. In this work, we examined a pure anatase TiO2 as a model feedstock because of its photocatalytic attributes and well-characterized properties. After the SPP treatment, the pure anatase crystalline phase was transformed to an anatase/brookite heterocrystalline phase with oxygen vacancies. Furthermore, the SPP treatment promoted the absorption of both UV and visible light by TiO2. As a result, TiO2 treated by the SPP for 3 h showed a high gaseous photocatalytic performance (91.1%) for acetaldehyde degradation to CO2 compared with the activity of untreated TiO2 (51%). The SPP-treated TiO2 was also more active than nitrogen-doped TiO2 driven by visible light (66%). The overall photocatalytic performance was related to the SPP treatment time. The SPP technique could be used to enhance the activity of readily available feedstocks with a short processing time. These results demonstrate the potential of this method for modifying narrow-band gap metal oxides, metal sulfides, and polymer composite-based catalyst materials. The modifications of these materials are not limited to photocatalysts and could be used in a wide range of energy and environment-based applications.
| S-EPMC6641279 | biostudies-literature
Project description:The removal of antibiotics from wastewater to prevent their environmental accumulation is significant for human health and ecosystems. Herein, iron (Fe)-atom-doped anatase TiO2 nanofibers (Fe-TNs) were manufactured for the photocatalytic Fenton-like decomposition of tylosin (TYL) under LED illumination. Compared with the pristine TiO2 nanofibers (TNs), the optimized Fe-TNs exhibited improved visible-light-driven photocatalytic Fenton-like activity with a TYL degradation efficiency of 98.5% within 4 h. The effective TYL degradation could be attributed to the expanded optical light absorption and accelerated separation and migration of photogenerated electrons and holes after the introduction of Fe. The photogenerated electrons were highly conducive to the generation of active SO4•- radicals as they facilitated Fe(III)/Fe(II) cycles, and to oxidizing TYL. Moreover, the holes could be involved in TYL degradation. Thus, a significant enhancement in TYL degradation could be achieved. This research verifies the use of iron-doped anatase nanofibers as an effective method to synthesize novel photocatalytic Fenton-like catalysts through surface engineering for wastewater remediation.
| S-EPMC10574164 | biostudies-literature
Project description:At present, the types of pollutants in wastewater are more and more complicated, however, the multifunctional membrane materials are in short supply. To prepare a membrane with both high efficient oil-in-water emulsion separation performance and photocatalytic degradation performance of organic dyes, the bifunctional separation membrane was successfully prepared by electrostatic spinning technology of PVDF/PEMA and in situ deposition of anatase TiO2 nanoparticles containing Ti3+ and oxygen vacancies (Ov). The prepared composite membrane has excellent hydrophilic properties (WCA = 15.65), underwater oleophobic properties (UOCA = 156.69), and photocatalytic performance. These composite membranes have high separation efficiency and outstanding anti-fouling performance, the oil removal efficiency reaches 98.95%, and the flux recovery rate (FRR) reaches 99.19% for soybean oil-in-water emulsion. In addition, the composite membrane has outstanding photocatalytic degradation performance, with 97% and 90.2% degradation of RhB and AG-25 under UV conditions, respectively. Several oil-in-water separation and dye degradation experiments show that the PVDF composite membrane has excellent reuse performance. Based on these results, this study opens new avenues for the preparation of multifunctional reusable membranes for the water treatment field.
| S-EPMC10055995 | biostudies-literature
Project description:The existence of the oxidation/reduction interface can promote the performance of a photocatalyst, due to its effect on the separation of photogenerated carriers and the surface reactivity. However, it is difficult to construct two sets of oxidation/reduction interfaces in a single crystal and compare their separation efficiency for photogenerated carriers. Introducing a high proportion of active facets into the co-exposed facets is even more challenging. Herein, a hollow anatase TiO2 tetrakaidecahedron (HTT) with two sets of oxidation/reduction interfaces ({001}/{101} and {001}/{110}) is synthesized by directional chemical etching. Theoretical and experimental results indicate that the {001}/{110} interface is a dominant oxidation/reduction interface, showing a better promotion on the separation of photogenerated carriers than the {001}/{101} interface. In the HTT, the ratio of dominant {001}/(110) is increased and the proportion of the active {110} facet is about 40% (generally about 15%). Therefore, the HTT shows excellent catalytic activity for photocatalytic reductive (hydrogen production) and oxidative (selective oxidation of sulfides) reactions. The HTT also demonstrates favorable photocatalytic activity for the cross-dehydrogenative coupling reaction, where both photogenerated electrons and photogenerated holes are involved, further verifying its high separation efficiency of photogenerated carriers and surface reactivity. This work provides an important guideline for developing advanced structures with a predetermined interface toward desired applications.
| S-EPMC10762932 | biostudies-literature