Slippery nanoemulsion-infused porous surfaces (SNIPS): anti-fouling coatings that can host and sustain the release of water-soluble agents.
Ontology highlight
ABSTRACT:
SUBMITTER: Agarwal H
PROVIDER: S-EPMC8851892 | biostudies-literature | 2021 Nov
REPOSITORIES: biostudies-literature
Publications
Slippery nanoemulsion-infused porous surfaces (SNIPS): anti-fouling coatings that can host and sustain the release of water-soluble agents.
Agarwal Harshit H Polaske Thomas J TJ Sánchez-Velázquez Gabriel G Blackwell Helen E HE Lynn David M DM
Chemical communications (Cambridge, England) 20211125 94
We report the design of 'slippery' nanoemulsion-infused porous surfaces (SNIPS). These materials are strongly anti-fouling to a broad range of substances, including microorganisms. Infusion with water-in-oil nanoemulsions also endows these slippery coatings with the ability to host and control or sustain the release of water-soluble agents, including polymers, peptides, and nucleic acids, opening the door to new applications of liquid-infused materials. ...[more]
Similar Datasets
Project description:Slippery lubricant infused porous surfaces (SLIPS) have the potential to address daunting challenges such as undesirable surface fouling/biofouling, icing, etc. However, the depletion of lubricants hampers their practical utility. As a solution, here a rational strategy is introduced that operates synergistically in three parts. First, ultra-high capillary pressure is exploited from the reticular structure of metal-organic frameworks (MOFs) with sub-nanometer pores. Second, the need for geometric compatibility is demonstrated; the lubricant chain diameter must be smaller than the MOF pore to enable lubricant chain intercalation. Lastly, the MOF pore chemistry is tailored to achieve a strong intermolecular interaction for any given MOF/lubricant combination. The strategy is investigated through experiments and quantum/molecular simulations, which show that the approach helps lock the intercalated lubricant chains inside the MOF pores and forms a non-conventional supramolecular structure. The resulting SLIPS (including those with fluorine-free chemistry) not only show typical low wetting hysteresis, friction, and ice adhesion but are uniquely resistant to more stringent tests such as continuous dripping and sliding of water droplets (up to 50 hrs), repeated impacts of high-speed water jets (liquid impact Weber number > 4 × 104) and prevent bacterial biofilm formation even in dynamic flow conditions. The findings may widen the practical applications of SLIPS.
| S-EPMC11636059 | biostudies-literature
Project description:Many types of slippery liquid-infused porous surfaces (or 'SLIPS') can resist adhesion and colonization by microorganisms. These 'slippery' materials thus offer new approaches to prevent fouling on a range of commercial and industrial surfaces, including biomedical devices. However, while SLIPS can prevent fouling on surfaces to which they are applied, they can currently do little to prevent the proliferation of non-adherent (planktonic) organisms, stop them from colonizing other surfaces, or prevent them from engaging in other behaviors that could lead to infection and associated burdens. Here, we report an approach to the design of multi-functional SLIPS that addresses these issues and expands the potential utility of slippery surfaces in antimicrobial contexts. Our approach is based on the incorporation and controlled release of small-molecule antimicrobial agents from the porous matrices used to host infused slippery oil phases. We demonstrate that SLIPS fabricated using nanoporous polymer multilayers can prevent short- and longer-term colonization and biofilm formation by four common fungal and bacterial pathogens (Candida albicans, Pseudomonas aeruginosa, Escherichia coli, and Staphylococcus aureus), and that the polymer and oil phases comprising these materials can be exploited to load and sustain the release of triclosan, a model hydrophobic and broad-spectrum antimicrobial agent, into surrounding media. This approach both improves the inherent anti-fouling properties of these materials and endows them with the ability to efficiently kill planktonic pathogens. Finally, we show that this approach can be used to fabricate dual-action SLIPS on complex surfaces, including the luminal surfaces of flexible catheter tubes. This strategy has the potential to be general; we anticipate that the materials, strategies, and concepts reported here will enable new approaches to the design of slippery surfaces with improved anti-fouling properties and open the door to new applications of slippery liquid-infused materials that host or promote the release of a variety of other active agents.
| S-EPMC5507623 | biostudies-literature
Project description:Icephobic coating and surfaces are essential for protecting infrastructures such as transmission lines, transportation vehicles, and many others from severe damages of excessive icing. The slippery liquid-infused porous surfaces (SLIPS) are attracting escalating attention because of their low-ice adhesion strength. Despite all of the encouraging laboratory scale results, the SLIPS are still far from being applicable in real environments owing to the key unsolved problem, namely anti-icing durability. Inspired by the functionality of the amphibians' skin, lubricant regenerability was introduced to conventional SLIPS and realized by a facile and scalable fabrication route. A series of polydimethylsiloxane (PDMS)-based skinlike SLIPS were designed and fabricated by using a one-step method, the solvent evaporation-induced phase separation technique. The obtained skinlike SLIPS were able to regenerate surface lubricant constantly by internal residual stress because of phase separation and survive more than 15 cycles of wiping/regenerating tests. Thanks to the regenerability of the surface lubricant, the new SLIPS demonstrated durable icephobicity, showing a long-term low-ice adhesion strength below 70 kPa, which was only 43% of 160 kPa that for the pristine PDMS (Sylgard 184), even after 15 icing/deicing cycles. This work paves a new and facile way for achieving icephobic durability of SLIPS.
| S-EPMC6645152 | biostudies-literature
Project description:Slippery liquid-infused porous surfaces (SLIPS) are self-healing
| S-EPMC10433335 | biostudies-literature
Project description:We report a layer-by-layer suction-and-flow approach that enables the fabrication of polymer-based "slippery" liquid-infused porous surfaces (SLIPS) in the confined luminal spaces of flexible, narrow-bore tubing. These SLIPS-coated tubes can prevent or strongly reduce surface fouling after prolonged contact, storage, or flow of a broad range of complex fluids and viscoelastic materials, including many that are relevant in the contexts of medical devices (e.g., blood and urine), food processing (beverages and fluids), and other commercial and industrial applications. The robust and mechanically compliant nature of the nanoporous coating used to host the lubricating oil phase allows these coated tubes to be bent, flexed, and coiled repeatedly without affecting their inherent slippery and antifouling behaviors. Our results also show that SLIPS-coated tubes can prevent the formation of bacterial biofilms after prolonged and repeated flow-based exposure to the human pathogen Staphylococcus aureus and that the anti-biofouling properties of these coated tubes can be further improved or prolonged by coupling this approach with strategies that permit the sustained release of broad-spectrum antimicrobial agents. The suction-and-flow approach used here enables the application of slippery coatings in the confined luminal spaces of narrow-bore tubing that are difficult to access using several other methods for the fabrication of liquid-infused coatings and can be applied to tubing of arbitrary length and diameter. We anticipate that the materials and approaches reported here will prove useful for reducing or preventing biofouling, process fouling, and the clogging or occlusion of tubing in a wide range of consumer, industrial, and healthcare-oriented applications.
| S-EPMC8840327 | biostudies-literature
Project description:Often wetting is considered from the perspective of a single surface of a rigid substrate and its topographical properties such as roughness or texture. However, many substrates, such as membranes and meshes, have two useful surfaces. Such flexible substrates also offer the potential to be formed into structures with either a double-sided surface (e.g. by joining the ends of a mesh as a tape) or a single-sided surface (e.g. by ends with a half-twist). When a substrate possesses holes, it is also possible to consider how the spaces in the substrate may be connected or disconnected. This combination of flexibility, holes and connectedness can therefore be used to introduce topological concepts, which are distinct from simple topography. Here, we present a method to create a Slippery Liquid-Infused Porous Surface (SLIPS) coating on flexible conformable doubled-sided meshes and for coating complex geometries. By considering the flexibility and connectedness of a mesh with the surface properties of SLIPS, we show it is possible to create double-sided SLIPS materials with high droplet mobility and droplet control on both faces. We also exemplify the importance of flexibility using a mesh-based SLIPS pipe capable of withstanding laminar and turbulent flows for 180 and 90 minutes, respectively. Finally, we discuss how ideas of topology introduced by the SLIPS mesh might be extended to create completely new types of SLIPS systems, such as Mobius strips and auxetic metamaterials.
| S-EPMC6746700 | biostudies-literature
Project description:Sessile drop evaporation and condensation on slippery liquid-infused porous surfaces (SLIPS) is crucial for many applications. However, its modeling is complex since the infused lubricant forms a wetting ridge around the drop close to the contact line, which partially blocks the free surface area and decreases the drop evaporation rate. Although a good model was available after 2015, the effects of initial lubricant heights (hoil)i above the pattern, and the corresponding initial ridge heights (hr)i, lubricant viscosity, and solid pattern type were not well studied. This work fills this gap where water drop evaporations from SLIPS, which are obtained by infusing silicone oils (20 and 350 cSt) onto hydrophobized Si wafer micropatterns having both cylindrical and square prism pillars, are investigated under constant relative humidity and temperature conditions. With the increase of (hoil)i, the corresponding (hr)i increased almost linearly on lower parts of the drops for all SLIPS samples, resulting in slower drop evaporation rates. A novel diffusion-limited evaporation equation from SLIPS is derived depending on the available free liquid-air interfacial area, ALV, which represents the unblocked part of the total drop surface. The calculation of the diffusion constant, D, of water vapor in air from (dALV/dt) values obtained by drop evaporation was successful up to a threshold value of (hoil)i = 8 μm within ±7%, and large deviations (13-27%) were obtained when (hoil)i > 8 μm, possibly due to the formation of thin silicone oil cloaking layers on drop surfaces, which partially blocked evaporation. The increase of infused silicone oil viscosity caused only a slight increase (12-17%) in drop lifetimes. The effects of the geometry and size of the pillars on the drop evaporation rates were minimal. These findings may help optimize the lubricant oil layer thickness and viscosity used for SLIPS to achieve low operational costs in the future.
| S-EPMC10173461 | biostudies-literature
Project description:We report the design and characterization of liquid crystal (LC)-infused porous polymer membranes that can detect and report on the presence of natural and synthetic amphiphiles in aqueous solution. We demonstrate that thermotropic LCs can be infused into nanoporous polymer membranes to yield LC-infused surfaces that exhibit slippery behaviors in contact with a range of aqueous fluids. In contrast to conventional liquid-infused surfaces (LIS) or slippery liquid-infused porous surfaces (SLIPS) prepared using isotropic oils, aqueous solutions slide over the surfaces of these LC-infused materials at speeds that depend strongly upon the composition of the fluid, including the presence, concentration, or structure of a dissolved surfactant. In general, the sliding times of aqueous droplets on these LC-infused surfaces increase significantly (e.g., from times on the order of seconds to times on the order of minutes) with increasing amphiphile concentration, allowing sliding times to be used to estimate the concentration of the amphiphile. Additional experiments revealed other intrinsic and extrinsic variables or parameters that can be used to further manipulate droplet sliding times and discriminate among amphiphiles of similar structure. Our results are consistent with a physical picture that involves reversible changes in the interfacial orientation of anisotropic LCs mediated by the interfacial adsorption of amphiphiles. These materials thus permit facile "naked-eye" detection and discrimination of amphiphiles in aqueous samples using equipment no more sophisticated than a stopwatch. We demonstrate the potential utility of these LC-infused surfaces for the unaided, naked-eye detection and monitoring of amphiphilic biotoxins in small droplets of fluid extracted directly from cultures of two common bacterial pathogens (Pseudomonas aeruginosa and Staphylococcus aureus). The ability to translate molecular interactions at aqueous/LC interfaces into large and readily observed changes in the sliding times of small aqueous droplets on surfaces could open the door to new applications for antifouling, liquid-infused materials in the context of environmental sensing and other fundamental and applied areas.
| S-EPMC8459213 | biostudies-literature
Project description:Magnetocontrollable droplet mobility on surfaces of both solids and simple fluids have been widely used in a wide range of applications. However, little is understood about the effect of the magnetic field on the wettability and mobility of droplets on structured fluids. Here, we report the manipulation of the dynamic behaviors of water droplets on a film of thermotropic liquid crystals (LCs). We find that the static wetting behavior and static friction of water droplets on a 4'-octyl-4-biphenylcarbonitrile (8CB) film strongly depend on the LC mesophases, and that a magnetic field caused no measurable change to these properties. However, we find that the droplet dynamics can be affected by a magnetic field as it slides on a nematic 8CB film, but not on isotropic 8CB, and is dependent on both the direction and strength of the magnetic field. By measuring the dynamic friction of a droplet sliding on a nematic 8CB film, we find that a magnetic field alters the internal orientational ordering of the 8CB which in turn affects its viscosity. We support this interpretation with a scaling argument using the LC magnetic coherence length that includes (i) the elastic energy from the long-range orientational ordering of 8CB and (ii) the free energy from the interaction between 8CB and a magnetic field. Overall, these results advance our understanding of droplet mobility on LC films and enable new designs for responsive surfaces that can manipulate the mobility of water droplets.Electronic supplementary materialSupplementary material (further details of the stability of LCIPS against water-induced dewetting, the interfacial tension and contact angle measurement using a goniometer, the estimation of the thickness of LC wrapping layer at air-water interface on droplets, SEM measurements, the average sliding velocity of a water droplet on 5CB, E7, silicone oil, and mineral oil films with and without a magnetic field, representative force diagram (Fd versus time) of a 3-µL water droplet moving at a speed of 0.1 mm/s on a nematic 8CB film, Fdynamic acting on 3 µL water droplets moving at speeds of 0.1-1 mm/s on an isotropic 8CB film, the calculated magnetic coherence length as a function of the magnitude of the magnetic field applied to the nematic LCIPS, and the apparent advancing and receding contact angles of a moving water droplet on nematic LCIPS as a function of time, and polarized light micrographs (top view) of a nematic 8CB film between two DMOAP-functionalized glass slides before and after applying a horizontal magnetic field) is available in the online version of this article at 10.1007/s12274-022-5318-y.
| S-EPMC9768411 | biostudies-literature
Project description:To address growing water scarcity, we must improve the energy efficiency of thermal desalination technologies such as air gap membrane distillation. However, promising functional materials such as slippery liquid infused porous surfaces have not yet implemented for any desalination technology. Here, we fabricate and test slippery liquid infused porous surfaces (using Krytox 16,256 lubricant and CuO nanostructures) in an air gap membrane distillation apparatus. System-level transport models, validated by experimental data, establish a framework for improving performance through enhanced condensation surfaces. Results are obtained across a range of temperatures (50-80 °C), salinities (5-105 g/kg), and module lengths. We find that small air gap thickness and efficient droplet shedding significantly improves performance. The CuO Krytox process achieves these with a conductive-self-limiting coating, high nanostructure rugosity, strong covalent and metallic bonding, high hydrophobicity, minimal droplet pinning sites, and ultra-low contact angle hysteresis. The greatest efficiency enhancement from SLIPS is derived from the improved droplet shedding, which allows for reduced gap sizes without flooding, and is further augmented by the increased permeate flux.
| S-EPMC11910583 | biostudies-literature