Browse
Submit Data
Databases
API
Help

Dataset Information

26 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

High Open Circuit Voltage Over 1 V Achieved in Tin-Based Perovskite Solar Cells with a 2D/3D Vertical Heterojunction.

ABSTRACT: 2D-3D mixed tin halide perovskites are outstanding candidate materials for lead-free perovskite solar cells (PSCs) due to their improved stability and decreased trap density in comparison with their pure 3D counterparts. However, the mixture of multiple phases may lead to poor charge transfer across the films and limit the device efficiency. Here, a stacked quasi-2D (down)-3D (top) double-layered structure in perovskite films prepared via vacuum treatment is demonstrated, which can result in a planar bilayer heterojunction. In addition, it is found that the introduction of guanidinium thiocyanate (GuaSCN) additive can improve the crystallinity and carrier mobility in the 2D perovskite layer and passivate defects in the whole film, leading to a long carrier lifetime (>140 ns) in photoluminescence measurements. As a result, the PSCs show a high open circuit voltage (V_OC ) up to 1.01 V with a voltage loss of only 0.39 V, which represents the record values ever reported for tin-based PSCs. The champion device exhibits a power conversion efficiency (PCE) of 13.79% with decent stability, retaining 90% of the initial PCE for 1200 h storage in N₂ -filled glovebox.

SUBMITTER: Wang T

PROVIDER: S-EPMC9218751 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Ultra-high open-circuit voltage of tin perovskite solar cells via an electron transporting layer design.

Project description:Tin perovskite is rising as a promising candidate to address the toxicity and theoretical efficiency limitation of lead perovskite. However, the voltage and efficiency of tin perovskite solar cells are much lower than lead counterparts. Herein, indene-C60 bisadduct with higher energy level is utilized as an electron transporting material for tin perovskite solar cells. It suppresses carrier concentration increase caused by remote doping, which significantly reduces interface carriers recombination. Moreover, indene-C60 bisadduct increases the maximum attainable photovoltage of the device. As a result, the use of indene-C60 bisadduct brings unprecedentedly high voltage of 0.94 V, which is over 50% higher than that of 0.6 V for device based on [6,6]-phenyl-C61-butyric acid methyl ester. The device shows a record power conversion efficiency of 12.4% reproduced in an accredited independent photovoltaic testing lab.

| S-EPMC7060347 | biostudies-literature

Monolithic Two-Terminal Perovskite/Perovskite/Silicon Triple-Junction Solar Cells with Open Circuit Voltage >2.8 V.

Project description:The efficiency of perovskite/silicon tandem solar cells has exceeded the previous record for III-V-based dual-junction solar cells. This shows the high potential of perovskite solar cells in multi-junction applications. Perovskite/perovskite/silicon triple-junction solar cells are now the next step to achieve efficient and low-cost multi-junction solar cells with an efficiency potential even higher than that for dual-junction solar cells. Here we present a perovskite/perovskite/silicon triple-junction solar cell with an open circuit voltage of >2.8 V, which is the record value reported for this structure so far. This is achieved through employing a gas quenching method for deposition of the top perovskite layer as well as optimization of interlayers between perovskite subcells. Moreover, for the measurement of our triple-junction solar cells, precise measurement procedures are implemented to ensure the reliability and accuracy of the reported values.

| S-EPMC10580312 | biostudies-literature

Tunable Open Circuit Voltage by Engineering Inorganic Cesium Lead Bromide/Iodide Perovskite Solar Cells.

Project description:Perovskite solar cells based on series of inorganic cesium lead bromide and iodide mixture, CsPbBr3-xI x , where x varies between 0, 0.1, 0.2, and 0.3 molar ratio were synthesized by two step-sequential deposition at ambient condition to design the variations of wide band gap light absorbers. A device with high overall photoconversion efficiency of 3.98 % was obtained when small amount of iodide (CsPbBr2.9I0.1) was used as the perovskite and spiro-OMeTAD as the hole transport material (HTM). We investigated the origin of variation in open circuit voltage, Voc which was shown to be mainly dependent on two factors, which are the band gap of the perovskite and the work function of the HTM. An increment in Voc was observed for the device with larger perovskite band gap, while keeping the electron and hole extraction contacts the same. Besides, the usage of bilayer P3HT/MoO3 with deeper HOMO level as HTM instead of spiro-OMeTAD, thus increased the Voc from 1.16 V to 1.3 V for CsPbBr3 solar cell, although the photocurrent is lowered due to charge extraction issues. The stability studies confirmed that the addition of small amount of iodide into the CsPbBr3 is necessarily to stabilize the cell performance over time.

| S-EPMC5802841 | biostudies-literature

Enhanced Open-Circuit Voltage in Perovskite Solar Cells with Open-Cage [60]Fullerene Derivatives as Electron-Transporting Materials.

Project description:The synthesis, characterization, and incorporation of open-cage [60]fullerene derivatives as electron-transporting materials (ETMs) in perovskite solar cells (PSCs) with an inverted planar (p-i-n) structure is reported. Following optical and electrochemical characterization of the open-cage fullerenes 2a-c, p-i-n PSCs with a indium tin oxide (ITO)/poly(3,4-ethylenedioxythiophene)-polystyrene sulfonate (PEDOT:PSS)/perovskite/fullerene/Ag structure were prepared. The devices obtained from 2a-b exhibit competitive power conversion efficiencies (PCEs) and improved open-circuit voltage (Voc) values (>1.0 V) in comparison to a reference cell based on phenyl-C61-butyric-acid methyl-ester (PC61BM). These results are rationalized in terms of a) the higher passivation ability of the open-cage fullerenes with respect to the other fullerenes, and b) a good overlap between the highest occupied molecular orbital/lowest unoccupied molecular orbital (HOMO/LUMO) levels of 2a-b and the conduction band of the perovskite.

| S-EPMC6515431 | biostudies-literature

High-Performance Simple-Structured Planar Heterojunction Perovskite Solar Cells Achieved by Precursor Optimization.

Project description:Planar perovskite solar cells (PSCs) with perovskite and [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) heterojunction have attracted much interest because they can be fabricated by a low-temperature process and exhibit high power conversion efficiency (PCE). Various compositional engineering and interface engineering approaches have been applied to produce high-performance PSC devices. In this study, we found that high-quality lead halide crystal precursor has a significant effect on the perovskite film quality and it could enhance perovskite film light absorption, reduce crystal defects, and suppress charge recombination, resulting in enhanced device performance (from 8.9 to 15.0% for CH3NH3PbI3 and from 14.2 to 18.0% for MA0.7FA0.3PbI3-x Cl x ). Moreover, electron and hole interlayer free devices were achieved by using high-quality PbI2 crystals and the devices exhibited a high PCE of 13.6 and 10.4% for glass and flexible substrates, respectively. This is important for simplifying the perovskite solar cell fabrication process without complex interface engineering involved, especially for printed PSCs.

| S-EPMC6644478 | biostudies-literature

Ultra-high open-circuit voltage of perovskite solar cells induced by nucleation thermodynamics on rough substrates.

Project description:To obtain high performance CH3NH3PbI3 perovskite solar cells, it is highly important to realise a high open-circuit voltage. Calculation results based on a modified diode model have indicated that a low bare ratio ? of the perovskite film is the most important factor determining the open-circuit voltage, where ? is defined as the ratio of the projection of the uncovered area of the perovskite film to the apparent area of the total substrate surface. To realise a low ?, we investigate the nucleation behaviour of crystals on rough substrates. The analysis results predict that, when CH3NH3PbI3 is deposited on conventional transparent conductive oxide substrates such as fluorine-doped tin oxide, preferential heterogeneous nucleation will occur on the concave regions of the substrate; then, depending on the subsequent growth step, full coverage of the perovskite film at both the macroscopic and microscopic scales is realised. As a result, an ultra-high open-circuit voltage, i.e., 1.20?V, can be achieved in devices using the full coverage CH3NH3PbI3 film. The thermodynamics theory of precipitation nucleation should shed light on solution engineering of thin films.

| S-EPMC5388881 | biostudies-literature

Investigation on the Overshoot of Transient Open-Circuit Voltage in Methylammonium Lead Iodide Perovskite Solar Cells.

Project description:Although the performance of hybrid organic-inorganic perovskite solar cells (PSCs) is encouraging, the detailed working principles and mechanisms of PSCs remain to be further studied. In this work, an overshoot phenomenon of open-circuit voltage (Voc) was observed when the illumination light pulse was switched off. The evolution of the Voc overshoot was systematically investigated along with the intensity and the width of the light pulse, the background illumination, and pretreatment by different bias. Based on the experimental results, we could conclude that the Voc overshoot originated from carrier motion against carrier collection direction, which happened at the ionic-accumulation-induced band bending areas near the interfaces between the perovskite active layer and the two carrier transport layers. The investigation on the Voc overshoot can help us to better understand ionic migration, carrier accumulation, and recombination of PSCs under open-circuit conditions.

| S-EPMC6316959 | biostudies-literature

On the origin of open-circuit voltage losses in flexible <i>n-i-p</i> perovskite solar cells.

Project description:The possibility to manufacture perovskite solar cells (PSCs) at low temperatures paves the way to flexible and lightweight photovoltaic (PV) devices manufactured via high-throughput roll-to-roll processes. In order to achieve higher power conversion efficiencies, it is necessary to approach the radiative limit via suppression of non-radiative recombination losses. Herein, we performed a systematic voltage loss analysis for a typical low-temperature processed, flexible PSC in n-i-p configuration using vacuum deposited C60 as electron transport layer (ETL) and two-step hybrid vacuum-solution deposition for CH3NH3PbI3 perovskite absorber. We identified the ETL/absorber interface as a bottleneck in relation to non-radiative recombination losses, the quasi-Fermi level splitting (QFLS) decreases from ~1.23 eV for the bare absorber, just ~90 meV below the radiative limit, to ~1.10 eV when C60 is used as ETL. To effectively mitigate these voltage losses, we investigated different interfacial modifications via vacuum deposited interlayers (BCP, B4PyMPM, 3TPYMB, and LiF). An improvement in QFLS of ~30-40 meV is observed after interlayer deposition and confirmed by comparable improvements in the open-circuit voltage after implementation of these interfacial modifications in flexible PSCs. Further investigations on absorber/hole transport layer (HTL) interface point out the detrimental role of dopants in Spiro-OMeTAD film (widely employed HTL in the community) as recombination centers upon oxidation and light exposure.

| S-EPMC6691881 | biostudies-literature

Reducing Surface Recombination by a Poly(4-vinylpyridine) Interlayer in Perovskite Solar Cells with High Open-Circuit Voltage and Efficiency.

Project description:Identifying and reducing the dominant recombination processes in perovskite solar cells is one of the major challenges for further device optimization. Here, we show that introducing a thin interlayer of poly(4-vinylpyridine) (PVP) between the perovskite film and the hole transport layer reduces nonradiative recombination. Employing such a PVP interlayer, we reach an open-circuit voltage of 1.20 V for the best devices and a stabilized efficiency of 20.7%. The beneficial effect of the PVP interlayer is proven by statistical analysis of various samples, many of those showing an open-circuit voltage larger than 1.17 V, and a 30 mV increase in average compared to unmodified samples. The reduced nonradiative recombination is proven by enhanced photo- and electroluminescence yields.

| S-EPMC6642033 | biostudies-literature

Enhanced open-circuit voltage of PbS nanocrystal quantum dot solar cells.

Project description:Nanocrystal quantum dots (QD) show great promise toward improving solar cell efficiencies through the use of quantum confinement to tune absorbance across the solar spectrum and enable multi-exciton generation. Despite this remarkable potential for high photocurrent generation, the achievable open-circuit voltage (Voc) is fundamentally limited due to non-radiative recombination processes in QD solar cells. Here we report the highest open-circuit voltages to date for colloidal QD based solar cells under one sun illumination. This Voc of 692 ± 7?mV for 1.4?eV PbS QDs is a result of improved passivation of the defective QD surface, demonstrating Voc(mV)=553Eg/q-59 as a function of the QD bandgap (Eg). Comparing experimental Voc variation with the theoretical upper-limit obtained from one diode modeling of the cells with different Eg, these results clearly demonstrate that there is a tremendous opportunity for improvement of Voc to values greater than 1?V by using smaller QDs in QD solar cells.

| S-EPMC3715763 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data