Browse
Submit Data
Databases
API
Help

Dataset Information

18 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

An Air Velocity Monitor for Coal Mine Ventilation Based on Vortex-Induced Triboelectric Nanogenerator.

ABSTRACT: Air velocity of coal mine ventilation is an important consideration that may cause serious damage. This paper proposes a simple, low cost and effective air velocity monitor (AVM) for coal mine ventilation. The AVM uses the lock-in characteristic of vortex-induced vibration (VIV) to sense the air velocity. Amplitude of the VIV is converted into frequency signal of a vortex-induced triboelectric nanogenerator (VI-TENG) to improve the durability. Structure of the AVM are designed, and parameters of the AVM are optimized with experiments. For the upper and lower air velocity thresholds of 3.1 and 3.6 m/s, the optimized flexible beam length, slider weight, electrode space and electrode width are 42.5 mm, 0.4 g, 0.2 mm and 0.5 mm, respectively. Experiments also show that the output frequency of the VI-TENG could represent the amplitude of VIV well with the correlation coefficient of 0.93. Durability test demonstrates that the AVM generates stable output frequency in 120,000 cycles. A prototype and its controller are fabricated. Wind tunnel tests of this prototype show that it can give alarm when the gas velocity goes above the upper threshold or below the lower threshold. The proposed AVM could be a good solution for simple and effective coal mine ventilation alarm.

SUBMITTER: Shen G

PROVIDER: S-EPMC9268754 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Coal-packed methane biofilter for mitigation of green house gas emissions from coal mine ventilation air.

Project description:Methane emitted by coal mine ventilation air (MVA) is a significant greenhouse gas. A mitigation strategy is the oxidation of methane to carbon dioxide, which is approximately twenty-one times less effective at global warming than methane on a mass-basis. The low non-combustible methane concentrations at high MVA flow rates call for a catalytic strategy of oxidation. A laboratory-scale coal-packed biofilter was designed and partially removed methane from humidified air at flow rates between 0.2 and 2.4 L min-1 at 30°C with nutrient solution added every three days. Methane oxidation was catalysed by a complex community of naturally-occurring microorganisms, with the most abundant member being identified by 16S rRNA gene sequence as belonging to the methanotrophic genus Methylocystis. Additional inoculation with a laboratory-grown culture of Methylosinus sporium, as investigated in a parallel run, only enhanced methane consumption during the initial 12 weeks. The greatest level of methane removal of 27.2±0.66 g methane m-3 empty bed h-1 was attained for the non-inoculated system, which was equivalent to removing 19.7±2.9% methane from an inlet concentration of 1% v/v at an inlet gas flow rate of 1.6 L min-1 (2.4 min empty bed residence time). These results show that low-cost coal packing holds promising potential as a suitable growth surface and contains methanotrophic microorganisms for the catalytic oxidative removal of methane.

| S-EPMC3990720 | biostudies-literature

Integrated charge excitation triboelectric nanogenerator.

Project description:Performance of triboelectric nanogenerators is limited by low and unstable charge density on tribo-layers. An external-charge pumping method was recently developed and presents a promising and efficient strategy towards high-output triboelectric nanogenerators. However, integratibility and charge accumulation efficiency of the system is rather low. Inspired by the historical development of electromagnetic generators, here, we propose and realize a self-charge excitation triboelectric nanogenerator system towards high and stable output in analogy to the principle of traditional magnetic excitation generators. By rational design of the voltage-multiplying circuits, the completed external and self-charge excitation modes with stable and tailorable output over 1.25 mC m-2 in contact-separation mode have been realized in ambient condition. The realization of the charge excitation system in this work may provide a promising strategy for achieving high-output triboelectric nanogenerators towards practical applications.

| S-EPMC6440990 | biostudies-literature

Selection rules of triboelectric materials for direct-current triboelectric nanogenerator.

Project description:The rapid development of Internet of Things and artificial intelligence brings increasing attention on the harvesting of distributed energy by using triboelectric nanogenerator (TENG), especially the direct current TENG (DC-TENG). It is essential to select appropriate triboelectric materials for obtaining a high performance TENG. In this work, we provide a set of rules for selecting the triboelectric materials for DC-TENG based on several basic parameters, including surface charge density, friction coefficient, polarization, utilization rate of charges, and stability. On the basis of the selection rules, polyvinyl chloride, used widely in industry rather than in TENG, is selected as the triboelectric layer. Its effective charge density can reach up to ~8.80 mC m-2 in a microstructure-designed DC-TENG, which is a new record for all kinds of TENGs. This work can offer a basic guideline for the triboelectric materials selection and promote the practical applications of DC-TENG.

| S-EPMC8333059 | biostudies-literature

Cellulose II Aerogel-Based Triboelectric Nanogenerator.

Project description:Cellulose-based triboelectric nanogenerators (TENGs) have gained increasing attention. In this study, a novel method is demonstrated to synthesize cellulose-based aerogels and such aerogels are used to fabricate TENGs that can serve as mechanical energy harvesters and self-powered sensors. The cellulose II aerogel is fabricated via a dissolution-regeneration process in a green inorganic molten salt hydrate solvent (lithium bromide trihydrate), where. The as-fabricated cellulose II aerogel exhibits an interconnected open-pore 3D network structure, higher degree of flexibility, high porosity, and a high surface area of 221.3 m2 g-1. Given its architectural merits, the cellulose II aerogel-based TENG presents an excellent mechanical response sensitivity and high electrical output performance. By blending with other natural polysaccharides, i.e., chitosan and alginic acid, electron-donating and electron-withdrawing groups are introduced into the composite cellulose II aerogels, which significantly improves the triboelectric performance of the TENG. The cellulose II aerogel-based TENG is demonstrated to light up light-emitting diodes, charge commercial capacitors, power a calculator, and monitor human motions. This study demonstrates the facile fabrication of cellulose II aerogel and its application in TENG, which leads to a high-performance and eco-friendly energy harvesting and self-powered system.

| S-EPMC7357570 | biostudies-literature

High performance temperature difference triboelectric nanogenerator.

Project description:Usually, high temperature decreases the output performance of triboelectric nanogenerator because of the dissipation of triboelectric charges through the thermionic emission. Here, a temperature difference triboelectric nanogenerator is designed and fabricated to enhance the electrical output performance in high temperature environment. As the hotter friction layer's temperature of nanogenerator is 0 K to 145 K higher than the cooler part's temperature, the output voltage, current, surface charge density and output power are increased 2.7, 2.2, 3.0 and 2.9 times, respectively (from 315 V, 9.1 μA, 19.6 μC m-2, 69 μW to 858 V, 20 μA, 58.8 μC m-2, 206.7 μW). With the further increase of temperature difference from 145 K to 219 K, the surface charge density and output performance gradually decrease. At the optimal temperature difference (145 K), the largest output current density is 443 μA cm-2, which is 26.6% larger than the reported record value (350 μA cm-2).

| S-EPMC8346487 | biostudies-literature

All printable snow-based triboelectric nanogenerator.

Project description:The development of power generators that can function in harsh snowy environments and in contact with snow can be beneficial but challenging to accomplish. Herein, we introduce the first snow-based triboelectric nanogenerator (snow-TENG) that can be used as an energy harvester and a multifunctional sensor based on the principle of snow-triboelectrification. In this work, we used a 3D printing technique for the precise design and deposition of the electrode and triboelectric layer, leading to flexible, stretchable and metal-free triboelectric generators. Based on the single electrode mode, the device can generate an instantaneous output power density as high as 0.2 mW/m2, an open circuit voltage up to 8 V, and a current density of 40 μA/m2. In addition, the snow-TENG can function as a miniaturized weather station to monitor the weather in real time to provide accurate information about the snowfall rate, snow accumulation depth, wind direction, and speed in snowy and/or icy environments. In addition, the snow-TENG can be used as a wearable power source and biomechanical sensor to detect human body motions, which may prove useful for snow-related sports. Unlike conventional sensor platforms, our design works without the need for batteries or image processing systems. We envision these devices could potentially be integrated into solar panels to ensure continuous power supply during snowy weather conditions.

| S-EPMC7497792 | biostudies-literature

Effective energy storage from a triboelectric nanogenerator.

Project description:To sustainably power electronics by harvesting mechanical energy using nanogenerators, energy storage is essential to supply a regulated and stable electric output, which is traditionally realized by a direct connection between the two components through a rectifier. However, this may lead to low energy-storage efficiency. Here, we rationally design a charging cycle to maximize energy-storage efficiency by modulating the charge flow in the system, which is demonstrated on a triboelectric nanogenerator by adding a motion-triggered switch. Both theoretical and experimental comparisons show that the designed charging cycle can enhance the charging rate, improve the maximum energy-storage efficiency by up to 50% and promote the saturation voltage by at least a factor of two. This represents a progress to effectively store the energy harvested by nanogenerators with the aim to utilize ambient mechanical energy to drive portable/wearable/implantable electronics.

| S-EPMC4793045 | biostudies-literature

Restoring Tactile Sensation Using a Triboelectric Nanogenerator.

Project description:Loss of tactile sensation is a common occurrence in patients with traumatic peripheral nerve injury or soft tissue loss, but as yet, solutions for restoring such sensation are limited. Implanted neuro-prosthetics are a promising direction for tactile sensory restoration, but available technologies have substantial shortcomings, including complexity of use and of production and the need for an external power supply. In this work, we propose, fabricate, and demonstrate the use of a triboelectric nanogenerator (TENG) as a relatively simple, self-powered, biocompatible, sensitive, and flexible device for restoring tactile sensation. This integrated tactile TENG (TENG-IT) device is implanted under the skin and translates tactile pressure into electrical potential, which it relays via cuff electrodes to healthy sensory nerves, thereby stimulating them, to mimic tactile sensation. We show that the device elicits electrical activity in sensory neurons in vitro, and that the extent of this activity is dependent on the level of tactile pressure applied to the device. We subsequently demonstrate the TENG-IT in vivo, showing that it provides tactile sensation capabilities (as measured by a von Frey test) to rats in which sensation in the hindfoot was blocked through transection of the distal tibial nerve. These findings point to the substantial potential of self-powered TENG-based implanted devices as a means of restoring tactile sensation.

| S-EPMC8320237 | biostudies-literature

Effective energy harvesting from a single electrode based triboelectric nanogenerator.

Project description:The arch-shaped single electrode based triboelectric nanogenerator (TENG) is fabricated using thin film of reduced graphene oxide nanoribbons (rGONRs) with polyvinylidene fluoride (PVDF) polymer used as binder to effectively convert mechanical energy into electrical energy. The incorporation of rGONRs in PVDF polymer enhances average surface roughness of rGONRs/PVDF thin film. With the combination of the enhancement of average roughness and production of functional groups, which indicate improve charge storage capacity of prepared film. Furthermore, the redox peaks obtained through cyclic voltammetry were identified more in rGONRs/PVDF composite in comparison to pristine rGONRs to confirm charge transfer capability of film. Herein, the output performance was discussed experimentally as well as theoretically, maximum voltage was obtained to be 0.35?V. The newly designed TENG to harvest mechanical energy and opens up many new avenues of research in the energy harvesting applications.

| S-EPMC5153641 | biostudies-other

Triboelectric Nanogenerator (TENG) Mass Spectrometry of Falsified Antimalarials.

Project description:RationaleAn epidemic of low quality medicines continues to endanger patients worldwide. Detection of such "medicines" requires low cost, ambient ionization sources coupled to fieldable mass spectrometers for optimum sensitivity and specificity. With the use of triboelectric nanogenerators (TENGs), the charge required to produce gas-phase ions for mass analysis can be obtained without the need for high voltage electrical circuitry, simplifying and lowering the cost of next-generation mass spectrometry instruments.MethodsA sliding freestanding (SF) TENG was coupled to a toothpick electrospray setup for the purposes of testing if falsified medicines could be fingerprinted by this approach. Extracts from both genuine and falsified medicines were deposited on the toothpick and the SF TENG actuated to generate electrical charges, resulting in gas-phase ions for both active pharmaceutical ingredients and excipients.ResultsOur previous work had shown that direct analysis in real-time (DART) ambient mass spectrometry can identify the components of multiple classes of falsified antimalarial medicines. Experiments performed in this study show that a simple extraction into methanol along with the use of a SF TENG-powered toothpick electrospray can provide similar detection capabilities, but with much simpler and rugged instrumentation, and without the need for compressed gases or high voltage ion source power supplies.ConclusionsTENG toothpick MS allows for rapid analyte ion detection in a safe and low-cost manner, providing robust sampling and ionization capabilities.

| S-EPMC6120538 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data