Direct Ink Writing of Recyclable Supramolecular Soft Actuators.
Ontology highlight
ABSTRACT:
SUBMITTER: Lugger SJD
PROVIDER: S-EPMC9301911 | biostudies-literature |
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:Soft actuators allowing multifunctional, multishape deformations based on single polymer films or bilayers remain challenging to produce. In this contribution, direct ink writing is used for generating patterned actuators, which are in between single- and bilayer films, with multifunctionality and a plurality of possible shape changes in a single object. The key is to use the controlled deposition of a light-responsive liquid crystal ink with direct ink writing to partially cover a foil at strategic locations. We found patterned films with 40% coverage of the passive substrate by an active material outperformed "standard" fully covered bilayers. By patterning the film as two stripes, a range of motions, including left- and right-handed twisting and bending in orthogonal directions, could be controllably induced in the same actuator. The partial coverage also left space for applying liquid crystal inks with other functionalities, exemplified by fabricating a light-responsive green reflective actuator whose reflection can be switched "on" and "off". The results presented here serve as a toolbox for the design and fabrication of patterned actuators with dramatically expanded shape deformation and functionality capabilities.
| S-EPMC8678986 | biostudies-literature
Project description:Four-dimensional (4D) printing has attracted significant attention, because it enables structures to be reconfigured based on an external stimulus, realizing complex architectures that are useful for different applications. Nevertheless, most previously reported 4D-printed components have focused on actuators, which are just one part of a full soft robotic system. In this study, toward achieving fully 4D-printed systems, the design and direct ink writing of sensors with a straining mechanism that mimics the 4D effect are explored. Solution-processable carbon nanotubes (CNTs) were used as the sensing medium, and the effect of a heat-shrinkable shape-memory polymer-based substrate (i.e., potential 4D effect) on the electronic and structural properties of CNTs was assessed, followed by their application in various sensing devices. Herein, we reveal that substrate shrinking affords a more porous yet more conductive film owing to the compressive strain experienced by CNTs, leading to an increase in the carrier concentration. Furthermore, it improves the sensitivity of the devices without the need for chemical functionalization. Interestingly, the results show that, by engineering the potential 4D effect, the selectivity of the sensor can be tuned. Finally, the sensors were integrated into a fully 4D-printed flower structure, exhibiting their potential for different soft robotic applications.
| S-EPMC10976367 | biostudies-literature
Project description:In this work, polycaprolactone-polyethylene glycol (PCL-PEG) based waterborne polyurethane-urea (WBPUU) inks have been developed for an extrusion-based 3D printing technology. The WBPUU, synthesized from an optimized ratio of hydrophobic polycaprolactone diol and hydrophilic polyethylene glycol (0.2:0.8) in the soft segment, is able to form a physical gel at low solid contents. WBPUU inks with different solid contents have been synthesized. The rheology of the prepared systems was studied and the WBPUUs were subsequently used in the printing of different pieces to demonstrate the relationship between their rheological properties and their printing viability, establishing an optimal window of compositions for the developed WBPUU based inks. The results showed that the increase in solid content results in more structured inks, presenting a higher storage modulus as well as lower tan δ values, allowing for the improvement of the ink's shape fidelity. However, an increase in solid content also leads to an increase in the yield point and viscosity, leading to printability limitations. From among all printable systems, the WBPUU with a solid content of 32 wt% is proposed to be the more suitable ink for a successful printing performance, presenting both adequate printability and good shape fidelity, which leads to the realization of a recognizable and accurate 3D construct and an understanding of its relationship with rheological parameters.
| S-EPMC8232083 | biostudies-literature
Project description:Versatile printing of polymers, metals, and composites always calls for simple, economic approaches. Here we present an approach to three-dimensional (3D) printing of polymeric, metallic, and composite materials at room conditions, based on the polymeric vapor-induced phase separation (VIPS) process. During VIPS 3D printing (VIPS-3DP), a dissolved polymer-based ink is deposited in an environment where nebulized non-solvent is present, inducing the low-volatility solvent to be extracted from the filament in a controllable manner due to its higher chemical affinity with the non-solvent used. The polymeric phase is hardened in situ as a result of the induced phase separation process. The low volatility of the solvent enables its reclamation after the printing process, significantly reducing its environmental footprint. We first demonstrate the use of VIPS-3DP for polymer printing, showcasing its potential in printing intricate structures. We further extend VIPS-3DP to the deposition of polymer-based metallic inks or composite powder-laden polymeric inks, which become metallic parts or composites after a thermal cycle is applied. Furthermore, spatially tunable porous structures and functionally graded parts are printed by using the printing path to set the inter-filament porosity as well as an inorganic space-holder as an intra-filament porogen.
| S-EPMC11003993 | biostudies-literature
Project description:The application of reprocessable and reprogrammable soft actuators is limited by the synthetic strategies, 3D-shaping capabilities, and small deformations. In this work, melt-processable supramolecular soft actuators based on segmented copolymers containing thiourethane and liquid crystal segments have been prepared via sequential thiol addition reactions in a one-pot approach using commercially available building blocks. The actuators demonstrated immediate, reversible response and weightlifting capabilities with large deformations up to 32 %. Through exploiting the supramolecular cross-links, the material could be recycled and reprogrammed into 3D actuators and welded into an actuator assembly with different deformation modes. Our work offers a one-pot synthesis and straightforward melt-processable approach to prepare supramolecular soft actuators with large deformations that can be reprocessed and reprogrammed into arbitrary 3D shapes.
| S-EPMC9300041 | biostudies-literature
Project description:In this paper, we present a preliminary study and conceptual idea concerning 3D printing water-sensitive glass, using a borosilicate glass with high alkali and alkaline oxide contents as an example in direct ink writing. The investigated material was prepared in the form of a glass frit, which was further ground in order to obtain a fine powder of desired particle size distribution. In a following step, inks were prepared by mixing the fine glass powder with Pluoronic F-127 hydrogel. The acquired pastes were rheologically characterized and printed using a Robocasting device. Differential scanning calorimetry (DSC) experiments were performed for base materials and the obtained green bodies. After sintering, scanning electron microscope (SEM) and X-ray diffraction (XRD) analyses were carried out in order to examine microstructure and the eventual presence of crystalline phase inclusions. The results confirmed that the as obtained inks exhibit stable rheological properties despite the propensity of glass to undergo hydrolysis and could be adjusted to desirable values for 3D printing. No additional phase was observed, supporting the suitability of the designed technology for the production of water sensitive glass inks. SEM micrographs of the sintered samples revealed the presence of closed porosity, which may be the main reason of light scattering.
| S-EPMC7178419 | biostudies-literature
Project description:Poly(tetrafluoroethylene) (PTFE) is a unique polymer with highly desirable properties such as resistance to chemical degradation, biocompatibility, hydrophobicity, antistiction, and low friction coefficient. However, due to its high melt viscosity, it is not possible to three-dimensional (3D)-print PTFE structures using nozzle-based extrusion. Here, we report a new and versatile strategy for 3D-printing PTFE structures using direct ink writing (DIW). Our approach is based on a newly formulated PTFE nanoparticle ink and thermal treatment process. The ink was formulated by mixing an aqueous dispersion of surfactant-stabilized PTFE nanoparticles with a binding gum to optimize its shear-thinning properties required for DIW. We developed a multistage thermal treatment to fuse the PTFE nanoparticles, solidify the printed structures, and remove the additives. We have extensively characterized the rheological and mechanical properties and processing parameters of these structures using imaging, mechanical testing, and statistical design of experiments. Importantly, several of the mechanical and structural properties of the final-printed PTFE structures resemble that of compression-molded PTFE, and additionally, the mechanical properties are tunable. We anticipate that this versatile approach facilitates the production of 3D-printed PTFE components using DIW with significant potential applications in engineering and medicine.
| S-EPMC6813788 | biostudies-literature
Project description:Covalent functionalization of graphene (CFG) has shown attractive advantages in tuning the electronic, mechanical, optical, and thermal properties of graphene. However, facile, large-scale, controllable, and highly efficient CFG remains challenging and often involves highly reactive and volatile compounds, requiring complex control of the reaction conditions. Here, a diazonium-based grafting ink consisting of only two components, i.e., an aryl diazonium salt and the solvent dimethyl sulfoxide (DMSO) is presented. The efficient functionalization is attributed to the combination of the solvation of the diazonium cations by DMSO and n-doping of graphene by DMSO, thereby promoting electron transfer (ET) from graphene to the diazonium cations, resulting in the generation of aryl radicals which subsequently react with the graphene. The grafting density of CFG is controlled by the reaction time and very high levels of functionalization, up to the failing of the Tuinstra-Koenig (T-K) relation, while the functionalization layer remains at monolayer height. The grafting ink, effective for days at room temperature, can be used at ambient conditions and renders the patterning CFG by direct writing as easy as writing on paper. In combination with thermal sample treatment, reversible functionalization is possible by subsequent writing/erasing cycles.
| S-EPMC9259721 | biostudies-literature
Project description:Heart valve disease has become a serious global health problem, which calls for numerous implantable prosthetic valves to fulfill the broader needs of patients. Although current three-dimensional (3D) bioprinting approaches can be used to manufacture customized valve prostheses, they still have some complications, such as limited biocompatibility, constrained structural complexity, and difficulty to make heterogeneous constructs, to name a few. To overcome these challenges, a sacrificial scaffold-assisted direct ink writing approach has been explored and proposed in this work, in which a sacrificial scaffold is printed to temporarily support sinus wall and overhanging leaflets of an aortic valve prosthesis that can be removed easily and mildly without causing any potential damages to the valve prosthesis. The bioinks, composed of alginate, gelatin, and nanoclay, used to print heterogenous valve prostheses have been designed in terms of rheological/mechanical properties and filament formability. The sacrificial ink made from Pluronic F127 has been developed by evaluating rheological behavior and gel temperature. After investigating the effects of operating conditions, complex 3D structures and homogenous/heterogenous aortic valve prostheses have been successfully printed. Lastly, numerical simulation and cycling experiments have been performed to validate the function of the printed valve prostheses as one-way valves.
| S-EPMC10566457 | biostudies-literature
Project description:The ability to pattern planar and freestanding 3D metallic architectures at the microscale would enable myriad applications, including flexible electronics, displays, sensors, and electrically small antennas. A 3D printing method is introduced that combines direct ink writing with a focused laser that locally anneals printed metallic features "on-the-fly." To optimize the nozzle-to-laser separation distance, the heat transfer along the printed silver wire is modeled as a function of printing speed, laser intensity, and pulse duration. Laser-assisted direct ink writing is used to pattern highly conductive, ductile metallic interconnects, springs, and freestanding spiral architectures on flexible and rigid substrates.
| S-EPMC4896727 | biostudies-literature