Browse
Submit Data
Databases
API
Help

Dataset Information

28 Views

0 Connections

0 Citations

0 Reanalyses

0 Downloads

Omics score: 0

Moisture Dynamics of Wood-Based Panels and Wood Fibre Insulation Materials

ABSTRACT: Moisture performance is an important factor determining the resistance of wood-based building materials against fungal decay. Understanding how material porosity and chemistry affect moisture performance is necessary for their efficient use, as well as for product optimisation. In this study, three complementary techniques (X-ray computed tomography, infrared and low-field NMR spectroscopy) are applied to elucidate the influence of additives, manufacturing process and material structure on the liquid water absorption and desorption behaviour of a selection of wood-based panels, thermally modified wood and wood fibre insulation materials. Hydrophobic properties achieved by thermal treatment or hydrophobic additives such as paraffin and bitumen, had a major influence on water absorption and desorption rates. When hydrophobic additives did not play a role, pore distributions and manufacturing process had a decisive influence on the amount and rate of absorption and desorption. In that case, a higher porosity resulted in a higher water absorption rate. Our results show that there is a clear potential for tailoring materials towards specific moisture performance by better understanding the influence of different material characteristics. This is useful both for achieving desired moisture buffering as well as to increase service life of wood-based materials. From a sustainability perspective, fit-for-purpose moisture performance is often easier to achieve and preferred than wood protection by biocide preservative treatments.

SUBMITTER: De Ligne L

PROVIDER: S-EPMC9330446 | biostudies-literature |

REPOSITORIES: biostudies-literature

ACCESS DATA

Json Xml

Similar Datasets

Simultaneous change of wood mass and dimension caused by moisture dynamics.

Project description:An investigation of simultaneous dynamic mass and length change measurement for wood is presented. In contrast to the equilibrium in moisture content and swelling and shrinking, where extensive data exists for different wood species, less information is available for the dynamics of moisture changes in direct comparison to the related dimensional changes during the sorption process. This is due to a lack of methods. A gravimetric sorption system, equipped with a high resolution camera and an automated image evaluation, is used to examine simultaneous effects of water vapour sorption dynamics and dimensional change. This method proves a strong correlation between mass and dimensional change, which is in contrast to other investigations. Equilibrium moisture content as well as swelling and shrinking data is in good agreement with literature and manual measurements. The method enables the possibility to determine swelling and shrinking values in-situ without disturbing the targeted climatic conditions. The system is applicable for the investigation of natural wood, modified wood, wood composites or other lignocellulosic materials.

| S-EPMC6635364 | biostudies-literature

Properties of -O-Cu-O- Bridged Copper Phosphate-Based Thermal Insulation Materials.

Project description:P-O-H polycondensation -O-Cu-O- ion-bonded bridges were formed in copper phosphate thermal insulation materials by mixing Al(OH)3 dissolved in H3PO4 with CuO filler and Al2O3, SiC, ZrC, and Cr2O3 as curing accelerators, alone or in combination. The effects of different additive combinations on the curing behavior and thermal stability of the copper phosphate thermal insulation material matrixes were compared using thermogravimetry/differential scanning calorimetry, X-ray diffractometry, and scanning electron microscopy. The copper phosphate materials exhibit good thermal stabilities and low thermal conductivities. The thermal weight losses before and after ceramic reinforcement were 4-19.8 and 3.8-9.4%, respectively, and the thermal conductivities of the P-O-H polycondensation -O-Cu-O- ion-bonded bridges formed in the copper phosphate thermal insulation materials were in the range of 0.656-1.824 W/(m·K).

| S-EPMC6882121 | biostudies-literature

Experimental data for thermal conductivity and dielectric properties of wood and wood-based materials.

Project description:Empirical data and methods of measurements for the research article "Experimental correlation of thermal conductivity with dielectric properties of wood and wood-based construction materials: Possibilities for rapid in-situ building energy evaluation" by Saeed et al. [1] is presented. The data offers an insight into the possible correlation between thermal conductivity and dielectric properties of wood and wood-based materials. There is independent data on thermal conductivity and dielectric properties of wood in the literature. However, data correlating the two properties is scarce, making our dataset unique. Data on the dielectric properties, thermal conductivity, density, and moisture content of 30 solid wood and 17 wood-based materials is presented. Wood-based materials include plywood, OSB, chipboard, and MDF. Measurements were made on 50 mm x 25 mm samples, typically 25 mm thick. The thermal conductivity was measured using the steady state method with a heat flow meter apparatus. Dielectric properties were measured using an unshielded system of two electrodes with an LCR meter at 10 kHz and 100 kHz frequencies at room temperature. All measurements were made in the transverse direction for solid woods and perpendicular to the face of the boards for wood-based materials.

| S-EPMC8933817 | biostudies-literature

Preparation and Properties Study of Wood-Based Cushioning Materials.

Project description:Traditional cushioning package materials, such as Expended Polystyrene (EPS) and Expanded Polyethylene (EPE), were made with petroleum-based plastics, which are harmful to the environment. It is crucial to develop renewable bio-based cushioning materials that can replace the aforementioned foams due to the rising energy demands of human society and the depletion of fossil fuels. Herein, we report an effective strategy for creating anisotropic elastic wood with special spring-like lamellar structures. Selective removal of lignin and hemicellulose by simple chemical treatment and thermal treatment of the samples after freeze-drying results in an elastic material with good mechanical properties. The resulting elastic wood has a reversible compression rate of 60% and a high elastic recovery (99% height retention after 100 cycles at 60% strain). Drop tests revealed that the elastic wood has excellent cushioning properties. In addition, the chemical and thermal treatments also enlarge the pores in the material, which is favorable for subsequent functionalization. By loading the elastic wood with a muti-walled carbon nanotube (MWCNT), electromagnetic shielding properties are achieved, while the mechanical properties of elastic wood remain unchanged. Electromagnetic shielding materials can effectively suppress various electromagnetic waves propagating through space and the resulting electromagnetic interference and electromagnetic radiation, improve the electromagnetic compatibility of electronic systems and electronic equipment, and ensure the safety of information.

| S-EPMC10054834 | biostudies-literature

Eco-benign PVA/aluminum phosphate as an alternative to formaldehyde-based adhesives in wood-based panels.

Project description:Aluminum phosphate (AP) shows great potential to replace formaldehyde-based adhesives in the wood industry, except for its weak hygroscopic resistance and low wet bonding strength. This study chose PVA as an AP modifier to prepare a PVA-AP organic-inorganic hybrid adhesive (PAP). The preparation, bonding mechanism and heat resistant property of PAP were studied by using X-ray photoelectron spectroscopy (XPS), Fourier transforms infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetry-differential scanning calorimetry (TG-DSC), nuclear magnetic resonance (NMR) and scanning electron microscopy (SEM). The result showed that covalent bonds between PVA and AP were built. The mechanical properties of PAP improved remarkably; the dry and wet bonding strength are 2.28 and 0.79 MPa with 15.2% and 690% increment, respectively, compared to the control samples. The thermostabilities of PAP and plywood samples were improved. In conclusion, PVA could effectively improve the hygroscopic resistance and low wet bonding strength of AP adhesives.

| S-EPMC9042406 | biostudies-literature

Modeling Anomalous Moisture Transport in Cement-Based Materials with Kinetic Permeability.

Project description:The durability of reinforced concrete structures is closely related to moisture state in cement-based materials. Therefore, it is crucial to develop moisture models that can accurately predict moisture state in the materials. However, many studies reported anomalous moisture transport in cement-based materials that cannot be well simulated by the conventional models. Several reasons have been investigated in the literature, such as the complex pore structure, chemical reactions with water, dimensional changes of the tested specimen, etc. Nevertheless, only a few models are able to capture the anomaly of moisture transport. This study viewed the main moisture transport coefficient-permeability-as a kinetic variable that depends on both the degree of moisture saturation and the contact time. The time-dependence was formulated by the decay (for drying) or growth (for wetting) functions. The saturation-dependence was calculated by the van Genuchten-Mualem (VGM) model. These functions were then implemented into a moisture transport model that was developed in previous studies. The proposed model was validated by experimental data and showed a good agreement for cement pastes that were dried or wetted in the hygroscopic range. Numerical simulation results were also compared with the simplified solutions to a fractional derivative model (FDM) of anomalous diffusion and the empirical Weibull function. We found that the solutions to the FDM cannot provide appropriate results. Weibull function performs as well as the proposed model, but the empirical function lacks physical meanings.

| S-EPMC7037391 | biostudies-literature

Ecotoxicity and Biodegradation of Sustainable Environment-Friendly Bone-Glue-Based Adhesive Suitable for Insulation Materials.

Project description:Bone glue with sodium lignosulfonate is a protein-based adhesive. Their combination leads to strong binding necessary for the achievement of adhesive properties. However, biodegradation and ecotoxicity of materials composed of bone glue and sodium lignosulfonate has never been studied before. In this paper, the biodegradation potential of the mixture of bone glue, lignosulfonate and rape straw modified by water or NaOH on an agar test with aerial molds and in acute aquatic tests with mustard, yeasts, algae and crustaceans was analyzed. Epoxy resin as an ecologically unfriendly binder was used as a negative control and pure rape straw as a background. The results indicated that all samples were covered by molds, but the samples containing straw treated by NaOH showed lower biodegradability. The ecotoxicological effects varied among the applied model organisms. Artemia salina was not able to survive and S. alba could not prolong roots in the eluates of all samples (100% inhibition). Freshwater algae (D. subspicatus) were not significantly affected by the samples (max. 12% inhibition, max. 16% stimulation). The biomass of yeasts (S. cerevisae) was strongly stimulated in the presence of eluates in a comparison to control (max. 38% stimulation).

| S-EPMC9182703 | biostudies-literature

Chemical composition of material extractives influences microbial growth and dynamics on wetted wood materials.

Project description:The impact of material chemical composition on microbial growth on building materials remains relatively poorly understood. We investigate the influence of the chemical composition of material extractives on microbial growth and community dynamics on 30 different wood species that were naturally inoculated, wetted, and held at high humidity for several weeks. Microbial growth was assessed by visual assessment and molecular sequencing. Unwetted material powders and microbial swab samples were analyzed using reverse phase liquid chromatography with tandem mass spectrometry. Different wood species demonstrated varying susceptibility to microbial growth after 3 weeks and visible coverage and fungal qPCR concentrations were correlated (R2 = 0.55). Aspergillaceae was most abundant across all samples; Meruliaceae was more prevalent on 8 materials with the highest visible microbial growth. A larger and more diverse set of compounds was detected from the wood shavings compared to the microbial swabs, indicating a complex and heterogeneous chemical composition within wood types. Several individual compounds putatively identified in wood samples showed statistically significant, near-monotonic associations with microbial growth, including C11H16O4, C18H34O4, and C6H15NO. A pilot experiment confirmed the inhibitory effects of dosing a sample of wood materials with varying concentrations of liquid C6H15NO (assuming it presented as Diethylethanolamine).

| S-EPMC7467922 | biostudies-literature

Termites manipulate moisture content of wood to maximize foraging resources.

Project description:Animals use cues to find their food, in microhabitats within their physiological tolerances. Termites build and modify their microhabitat, to transform hostile environments into benign ones, which raises questions about the relative importance of cues. Termites are desiccation intolerant and foraging termites are attracted to water, so most research has considered moisture to be a cue. However, termites can also transport water to food, and so moisture may play other roles than previously considered. To examine the role of moisture, we compared Coptotermes acinaciformis termite foraging decisions in laboratory experiments when they were offered dry and moist wood, with and without load. Without load, termites preferred moist wood and ate it without any building, whereas they moistened dry wood after wrapping it in a layer of clay. For the 'With load' units, termites substituted some of the wood for load-bearing clay walls, and kept the wood drier than on the unloaded units. As drier wood has higher compressive strength and higher rigidity, it allows more of the wood to be consumed. These results suggest that moisture plays a more important role in termite ecology than previously thought. Termites manipulate the moisture content according to the situational context and use it for multiple purposes: increased moisture levels soften the fibre, which facilitates foraging, yet keeping the wood dry provides higher structural stability against buckling which is especially important when foraging on wood under load.

| S-EPMC6684979 | biostudies-literature

Wood Density and Moisture Content Estimation by Drilling Chips Extraction Technique.

Project description:The novelty of this study is the development of an accurate wood moisture content (MC) estimation method based on a relatively brand-new, non-destructive testing technique (drilling chips extraction). The method is especially important in the assessment of existing timber structures, where non-destructive testing (NDT) results are affected by wood MC and should be adjusted to a reference MC, usually 12%. In the assessment of timber structures, it is not possible to determine MC by oven drying method and this should be estimated. Electrical resistance and capacitance are the conventional methods used for MC estimation. This research work aims to present an accurate MC estimation method based on the drilling chips extraction technique. For that, 99 specimens (90 × 65 × 38 mm3) from three softwood and hardwood species covering a wide range of densities (from 355 to 978 kg m-3) were tested after conditioning at five different MCs (5%, 10%, 15%, 20%, 25%). The Wood Extractor device based on the drilling chips extraction technique was used. The mass of the chips collected (drilling residue) from each drill was recorded. The results show that the MC of the chips extracted was statistically significantly different than the MC of the specimen and cannot be directly used as MC determination. However, the chips MC can be used as an estimator of specimen MC with high determination coefficients (R2 from 71% to 86%). As the main result, models to estimate density directly adjusted to a reference 12% MC from the wet and dry mass of chips extracted were developed with an R2 of 98%. In sum, the drilling chips extractor is a dependable and straightforward method to estimate MC and density from only one measurement. Density adjusted to a reference 12% MC can be directly estimated from a single model.

| S-EPMC7178678 | biostudies-literature

OmicsDI is part of the ELIXIR infrastructure

OmicsDI is an Elixir interoperability service. Learn more ›

Tweets

OmicsDI Databases

PRIDE
PeptideAtlas
MassIVE
JPOST Repository
Physiome Model Repository

EGA
EVA
ENA
LINCS
PAXDB
Cell Collective

MetaboLights
Metabolomics Workbench
MetabolomeExpress
GNPS
BioModels
FAIRDOMHub

ArrayExpress
dbGaP
ExpressionAtlas
GEO
NODE

Information

Databases
Help
API
Contact us
Code on GitHub
Terms of use
Submit Data