Project description:Daytime radiative cooling (DRC) materials offer a sustainable approach to thermal management by exploiting net positive heat transfer to deep space. While such materials typically have a white or mirror-like appearance to maximize solar reflection, extending the palette of available colors is required to promote their real-world utilization. However, the incorporation of conventional absorption-based colorants inevitably leads to solar heating, which counteracts any radiative cooling effect. In this work, efficient sub-ambient DRC (Day: -4 °C, Night: -11 °C) from a vibrant, structurally colored film prepared from naturally derived cellulose nanocrystals (CNCs), is instead demonstrated. Arising from the underlying photonic nanostructure, the film selectively reflects visible light resulting in intense, fade-resistant coloration, while maintaining a low solar absorption (≈3%). Additionally, a high emission within the mid-infrared atmospheric window (>90%) allows for significant radiative heat loss. By coating such CNC films onto a highly scattering, porous ethylcellulose (EC) base layer, any sunlight that penetrates the CNC layer is backscattered by the EC layer below, achieving broadband solar reflection and vibrant structural color simultaneously. Finally, scalable manufacturing using a commercially relevant roll-to-roll process validates the potential to produce such colored radiative cooling materials at a large scale from a low-cost and sustainable feedstock.
Project description:Balancing physicochemical properties and sensory properties is one of the key points in expanding edible packaging applications. The work consisted of two parts, one was to investigate the effects of cellulose nanocrystals (CNC) on the packaging-related properties of whey protein isolate films with natural colorants (curcumin, phycocyanin, and lycopene) under freeze-thaw (FT) conditions; the other was to test oral tactility and visual sensory properties of the edible films and their overall acceptability in packed ice cream. FT treatment reduced the mechanical strength and moisture content and increased the water vapor permeability of the films, as water-phase transformation not only disrupted hydrogen bonds but also the film network structure through physical stress. The oral tactility produced by CNC and the visual effect produced by colorants could affect participants' preference for edible films. This study provides a good reference for the consumer-driven product development of packaged low-temperature products.
Project description:The fabrication of self-assembled cellulose nanocrystal (CNC) films of tunable photonic and mechanical properties using a facile, green approach is demonstrated. The combination of tunable flexibility and iridescence can dramatically expand CNC coating and film barrier capabilities for paints and coating applications, sustainable consumer packaging products, as well as effective templates for photonic and optoelectronic materials and structures.
Project description:The use of cellulose nanocrystals (CNC) in high performance coatings is attractive for micro-scale structures or device fabrication due to the anisotropic geometry, however CNC are insulating materials. Carbon nanotubes (CNT) are also rod-shaped nanomaterials that display high mechanical strength and electrical conductivity. The hydrophobic regions of surface-modified CNC can interact with hydrophobic CNT and aid in association between the two anisotropic nanomaterials. The long-range electrostatic repulsion of CNC plays a role in forming a stable CNT and CNC mixture dispersion in water, which is integral to forming a uniform hybrid film. At concentrations favorable for film formation, the multiwalled nanotubes + CNC mixture dispersion shows cellular network formation, indicating local phase separation, while the single-walled nanotube + CNC mixture dispersion shows schlieren texture, indicating liquid crystal mixture formation. Conductive CNT + CNC hybrid films (5-20 μm thick) were cast on glass microscope slides with and without shear by blade coating. The CNT + CNC hybrid films electrical conductivity increased with increasing CNT loadings and some anisotropy was observed with the sheared hybrid films, although to a lesser extent than what was anticipated. Percolation models were applied to model the hybrid film conductivity and correlate with the hybrid film microstructure.
Project description:Cellulose nanocrystals (CNCs) form chiral nematic phases in aqueous suspensions that can be preserved upon evaporation of water. The resulting films show an intense directional coloration determined by their microstructure. Here, microreflection experiments correlated with analysis of the helicoidal nanostructure of the films reveal that the iridescent colors and the ordering of the individual nematic layers are strongly dependent on the polydispersity of the size distribution of the CNCs. We show how this affects the self-assembly process, and hence multidomain color formation in such bioinspired structural films.
Project description:Passive radiative cooling (RC) enables the cooling of objects below ambient temperature during daytime without consuming energy, promising to be a game changer in terms of energy savings and CO2 reduction. However, so far most RC surfaces are obtained by energy-intensive nanofabrication processes or make use of unsustainable materials. These limitations are overcome by developing cellulose films with unprecedentedly low absorption of solar irradiance and strong mid-infrared (mid-IR) emittance. In particular, a cellulose-derivative (cellulose acetate) is exploited to produce porous scattering films of two different thicknesses, L ≈ 30 µm (thin) and L ≈ 300 µm (thick), making them adaptable to above and below-ambient cooling applications. The thin and thick films absorb only ≈5%${\approx}5\%$ of the solar irradiance, which represents a net cooling power gain of at least 17 W m-2 , compared to state-of-the-art cellulose-based radiative-cooling materials. Field tests show that the films can reach up to ≈5 °C below ambient temperature, when solar absorption and conductive/convective losses are minimized. Under dryer conditions (water column = 1 mm), it is estimated that the films can reach average minimum temperatures of ≈7-8 °C below the ambient. The work presents an alternative cellulose-based material for efficient radiative cooling that is simple to fabricate, cost-efficient and avoids the use of polluting materials.
Project description:Structurally colored fibers are attractive alternatives to chemically colored fibers due to their rich optical properties, color stability, and environmental friendliness. However, the fabrication of structurally colored fibers using cost-effective raw materials with the possibility to scale up remains challenging. Here, a simple and scalable approach is developed to fabricate continuous meter-long structurally colored fibers exhibiting brilliant structural colors across the visible spectrum and helix orientation-dependent polarization states. The fibers are fabricated by extrusion of concentrated aqueous solutions of chemically crosslinked hydroxypropyl cellulose (HPC). The wavelengths and polarization states can be tuned by solution concentration, relaxation time, and collector's surface energy. The HPC-based structurally colored fibers display excellent optical stability to mechanical straining, repeated drying/water impregnation, and prolonged heating at 150 °C. It is demonstrated that the HPC-based structurally colored fibers can be woven into structurally colored fabrics with wavelength- and polarization-coded optical patterns. The current work presents a strategy to tune the chiral nematic order, which constitutes an important step toward mass production of structurally colored fibers with stable and rich optical properties using easily available raw materials.
Project description:In the context of valorization of lignin produced from the pulp and paper industries, biodegradable UV-protection films were prepared using lignin and cellulose nanocrystals (CNCs). Initially, CNC films were optimized for improving their transparency by studying the effect of various sodium hydroxide (NaOH) concentrations. Maximum (%) transmittance of CNC film was obtained for NaOH addition between 3 and 4 wt %. The optimized CNC suspensions were used for incorporating alkaline lignin (AL) and softwood kraft lignin (SKL) in various concentrations (1-10 wt %). Morphological characterization showed homogeneity of the lignin distribution in CNC/lignin films. Complete UV blocking was achieved at 10 wt % lignin (AL or SKL) in CNC films. Cross-polarized optical microscopy and scanning electron microscopic images of films showed some degrees of global alignment of CNC rods upon addition of NaOH, which remained unaffected by lignin addition. Lignin modification through acetylation reduced the lignin color and improved visible light transmission of films without significantly affecting the UV-absorption properties. Presence of lignin also enhanced the thermal and contact angle stability of the films. This work shows for the first time that CNC aqueous suspensions with and without containing lignin could be tuned through the addition of NaOH to produce transparent and homogenous films, providing a simple and green approach in engineering CNC/lignin UV-protection films.
Project description:The ability to convert moisture signals into electrical signals through contactless control underpins a wide range of applications, including health monitoring, disaster warning, and energy harvesting. Despite its potential, the effective utilization of low-grade energy remains challenging, as it often requires complex device architectures that limit scalability and integration, particularly in wearable technologies. Here, we present a soft, flexible moisture-electric converter made from cellulose nanocrystals and polyvinyl alcohol composite films, designed for a novel touchless interactive platform. The device autonomously generates an electric output voltage of 200-700 mV in response to ambient moisture variations without requiring an external energy source. Its design, featuring a soft-adhered conductive carbon strip coupled with the composite film, provides high flexibility and portability. This configuration facilitates the creation of a non-contact control interface that seamlessly interacts with biological moisture from the human body, demonstrated by a mask that detects breathing conditions and a panel that measures contact distance. These advancements offer a promising pathway for developing flexible, intelligent electronic devices for wearable and touchless technologies.
Project description:Hydroxypropyl cellulose (HPC) is an edible, cost-effective and widely used derivative of cellulose. Under lyotropic conditions in water, HPC forms a photonic, liquid crystalline mesophase with an exceptional mechanochromic response. However, due to insufficient physical cross-linking photonic HPC can flow freely as a viscous liquid, preventing the exploitation of this mechanochromic material in the absence of any external encapsulation or structural confinement. Here this challenge is addressed by mixing HPC and gelatin in water to form a self-supporting, viscoelastic, and edible supramolecular photonic hydrogel. It is demonstrated that the structural coloration, mechanochromism and non-Newtonian shear-thinning behavior of the lyotropic HPC solutions can all be retained into the gel state. Moreover, the rigidity of the HPC-gel provides a 69% shorter mechanochromic relaxation time back to its initial color when compared to the liquid HPC-water only system, broadening the dynamic color range of HPC by approximately 2.5× in response to a compressive pressure. Finally, the ability to formulate the HPC-gels in a scalable fashion from only water and "food-grade" constituents unlocks a wide range of potential applications, from response-tunable mechanochromic materials and colorant-free food decoration, to short-term sensors in, for example, biodegradable "smart labels" for food packaging.