Energy Storage Triboelectric Nanogenerator Based on Ratchet Mechanism for Random Ocean Energy Harvesting
Ontology highlight
ABSTRACT:
SUBMITTER: Meng L
PROVIDER: S-EPMC9835160 | biostudies-literature | 2022 Dec
REPOSITORIES: biostudies-literature
Similar Datasets
Project description:As a new energy harvesting technology, triboelectric nanogenerators are widely used for vibration mechanical energy harvesting. However, the current schemes ignore the composite characteristics of vibration, with problems such as utilization and low collection efficiency. In this paper, a random resonance cantilever beam triboelectric nanogenerator (RCB-TENG) with dual-mode coupled is presented, the working mode is a coupling form of in-plane sliding and vertical contact-separation that can effectively collect complex vibration energy in transverse and longitudinal directions. The influences of the structural parameters of the RCB-TENG and different dielectric materials on the output performance are systematically investigated. The single vibration module achieved a power density of 463.56 mW/m2 and a transfer charge of 10.7 μC at a vibration frequency of 46 Hz, an increase in power density, and a transfer charge of 4.94 and 3.82 times, respectively, compared to the conventional contact-separation mode. Finally, the RCB-TENG was tested in practice, and it was observed that nine 1 W commercial LED bulbs and 500 5 mm diameter LED lamps were successfully lit. This work offers new ideas for distributed energy harvesting technologies and holds broad promise in the field of energy harvesting from wind, water, wave, and random vibrations caused by mechanical energy.
| S-EPMC9893744 | biostudies-literature
Project description:The arch-shaped single electrode based triboelectric nanogenerator (TENG) is fabricated using thin film of reduced graphene oxide nanoribbons (rGONRs) with polyvinylidene fluoride (PVDF) polymer used as binder to effectively convert mechanical energy into electrical energy. The incorporation of rGONRs in PVDF polymer enhances average surface roughness of rGONRs/PVDF thin film. With the combination of the enhancement of average roughness and production of functional groups, which indicate improve charge storage capacity of prepared film. Furthermore, the redox peaks obtained through cyclic voltammetry were identified more in rGONRs/PVDF composite in comparison to pristine rGONRs to confirm charge transfer capability of film. Herein, the output performance was discussed experimentally as well as theoretically, maximum voltage was obtained to be 0.35 V. The newly designed TENG to harvest mechanical energy and opens up many new avenues of research in the energy harvesting applications.
| S-EPMC5153641 | biostudies-literature
Project description:Triboelectric nanogenerators (TENG) have shown great potential in harvesting energy from water. For the TENG that harvests water energy, surface hydrophobicity is crucial for its performance. In this paper, we prepare a hydrophobic composite film of Polyvinylidene Fluoride/Polydimethylsiloxane/Polytetrafluoroethylene (PVDF/PDMS/PTFE) and an electrode of Polyaniline/Carbon nanotubes/Silver nanowires (PANI/CNTs/AgNWs) by electrospinning technology and a doping method, respectively, which are served as the friction layer and top electrode of TENG. The contact angle of the hydrophobic film and electrode both reach over 120°, which makes the separation process between water and the interface complete and promotes the output of TENG. The open-circuit voltage (Voc) and short-circuit current (Isc) can reach 150 V and 60 μA approximately. In addition, the composite electrode can be applied in the preparation of complex electrode shapes. Furthermore, the different reactions of TENG to different liquids indicate that it may contribute to liquid-type sensing systems. This work presents an efficient approach to fabricating hydrophobic films and electrodes, laying a foundation for the development of TENG for harvesting water energy.
| S-EPMC10419362 | biostudies-literature
Project description:The ocean covers 70% of the earth's surface and is one of the largest uncultivated resources still available for harvesting energy. The triboelectric energy harvesting technology has the potential to effectively convert the ocean's "blue energy" into electricity. A half-cylinder structure including rollers floating on the water has already been used, in which the pendulum motion of the rollers is driven by the waveform. For the stable motion of the rollers, the printed surface of the device was treated with acetone for attaining hydrophilicity. The electrical outputs with the proposed device were enhanced by increasing the contact surface area by simply implementing the double roller structure with double side-covered electrodes. With the optimized structure, the maximum power density reached a value of 69.34 µW m-2 at a load resistance of 200 MΩ with the device's high output durability. Finally, the fabricated device was also applied to the artificial water waves to demonstrate the possibility of using this device in the ocean. By simply modifying the electrode structure and adding a roller, this device demonstrated the ability to generate over 160% of electrical output with the same covered area of the ocean by the triboelectric nanogenerators (TENGs) and potential ocean application.
| S-EPMC8469981 | biostudies-literature
Project description:To sustainably power electronics by harvesting mechanical energy using nanogenerators, energy storage is essential to supply a regulated and stable electric output, which is traditionally realized by a direct connection between the two components through a rectifier. However, this may lead to low energy-storage efficiency. Here, we rationally design a charging cycle to maximize energy-storage efficiency by modulating the charge flow in the system, which is demonstrated on a triboelectric nanogenerator by adding a motion-triggered switch. Both theoretical and experimental comparisons show that the designed charging cycle can enhance the charging rate, improve the maximum energy-storage efficiency by up to 50% and promote the saturation voltage by at least a factor of two. This represents a progress to effectively store the energy harvested by nanogenerators with the aim to utilize ambient mechanical energy to drive portable/wearable/implantable electronics.
| S-EPMC4793045 | biostudies-literature
Project description:In this work, we use commercial powder particulates (a cosmetic fixing powder) as triboelectric materials for constructing a triboelectric nanogenerator (CFP-TENG). Through finger pressing, the CFP-TENG generated approximate open-circuit voltage, short-circuit current, and maximum power density values of 1141 V, 521 µA, and 570.96 μW/cm2, respectively. Thirty-seven commercial blue LEDs can be easily lit up by the CFP-TENG. Moreover, this TENG, which was designed as a novel palette structure for harvesting mechanical energy from bicycle motion, serves as a self-powered bicycle speed sensor. In addition, the cosmetic fixing powder can be used as an effective material to enhance the triboelectric property of skin. This study provides an effective method for developing a cost-effective TENG without the use of complex surface micro-/nano-texturing.
| S-EPMC6799839 | biostudies-literature
Project description:Harvesting energy from the surrounding environment, particularly from human body motions, is an effective way to provide sustainable electricity for low-power mobile and portable electronics. To get adapted to the human body and its motions, we report a new fiber-based triboelectric nanogenerator (FTNG) with a coaxial double helix structure, which is appropriate for collecting mechanical energy in different forms. With a small displacement (10 mm at 1.8 Hz), this FTNG could output 850.20 mV voltage and 0.66 mA m-2 current density in the lateral sliding mode, or 2.15 V voltage and 1.42 mA m-2 current density in the vertical separating mode. Applications onto the human body are also demonstrated: the output of 6 V and 600 nA (3 V and 300 nA) could be achieved when the FTNG was attached to a cloth (wore on a wrist). The output of FTNG was maintained after washing or long-time working. This FTNG is highly adaptable to the human body and has the potential to be a promising mobile and portable power supply for wearable electronic devices.
| S-EPMC9417421 | biostudies-literature
Project description:With the triboelectric nanogenerator developing in recent years, it has gradually become a promising alternative to fossil energy and batteries. Its rapid advancements also promote the combination of triboelectric nanogenerators and textiles. However, the limited stretchability of fabric-based triboelectric nanogenerators hindered their development in wearable electronic devices. Here, in combination with the polyamide (PA) conductive yarn, polyester multifilament, and polyurethane yarn, a highly stretchable woven fabric-based triboelectric nanogenerator (SWF-TENG) with the three elementary weaves is developed. Different from the normal woven fabric without elasticity, the loom tension of the elastic warp yarn is much larger than non-elastic warp yarn in the weaving process, which results in the high elasticity of the woven fabric coming from the loom. Based on the unique and creative woven method, SWF-TENGs are qualified with excellent stretchability (up to 300%), flexibility, comfortability, and excellent mechanical stability. It also exhibits good sensitivity and fast responsibility to the external tensile strain, which can be used as a bend-stretch sensor to detect and identify human gait. Its collected power under pressure mode is capable of lighting up 34 light-emitting diodes (LEDs) by only hand-tapping the fabric. SWF-TENG can be mass-manufactured by using the weaving machine, which decreases fabricating costs and accelerates industrialization. Based on these merits, this work provides a promising direction toward stretchable fabric-based TENGs with wide applications in wearable electronics, including energy harvesting and self-powered sensing.
| S-EPMC10004814 | biostudies-literature
Project description:Harvesting acoustic energy in the environment and converting it into electricity can provide essential ideas for self-powering the widely distributed sensor devices in the age of the Internet of Things. In this study, we propose a low-cost, easily fabricated and high-performance coniform Helmholtz resonator-based Triboelectric Nanogenerator (CHR-TENG) with the purpose of acoustic energy harvesting. Output performances of the CHR-TENG with varied geometrical sizes were systematically investigated under different acoustic energy conditions. Remarkably, the CHR-TENG could achieve a 58.2% higher power density per unit of sound pressure of acoustic energy harvesting compared with the ever-reported best result. In addition, the reported CHR-TENG was demonstrated by charging a 1000 μF capacitor up to 3 V in 165 s, powering a sensor for continuous temperature and humidity monitoring and lighting up as many as five 0.5 W commercial LED bulbs for acoustic energy harvesting. With a collection features of high output performance, lightweight, wide frequency response band and environmental friendliness, the cleverly designed CHR-TENG represents a practicable acoustic energy harvesting approach for powering sensor devices in the age of the Internet of Things.
| S-EPMC8705617 | biostudies-literature
Project description:This work reports a high-performance, low-cost, biocompatible triboelectric nanogenerator (TENG) using chicken skin (CS). The device is suitable to power wearable devices, which is critical to adapt electronics in monitoring, predicting, and treating people. It also supports sustainability by providing a cost-effective way to reduce the poultry industry's waste. It has been shown here that CS-derived biowaste is an effective means of generating tribopositive material for TENGs. The CS contains amino acid functional groups based on (Glycine, Proline, and Hydroxyproline), which are essential to demonstrate the electron-donating ability of collagen. The skin was cut into 3 × 3 cm2 and used as the raw material for fabricating the TENG device with a stacking sequence of Al/Kapton/spacing/CS/Al. The chicken skin-based TENG (CS-TENG) is characterized at different frequencies (4-14 HZ) using a damping system. The CS-TENG produces an open-circuit voltage of 123 V, short-circuit current of 20 µA and 0.2 mW/cm2 of a power density at 20 MΩ. The biocompatible CS-TENG presents ultra-robust and stable endurance performance with more than 52,000 cycles. The CS-TENG is impressively capable of scavenging energy to light up to 55 commercial light-emitting diodes (LEDs), a calculator, and to measure the physiological motions of the human body. CS-TENG is a step toward sustainable, battery-less devices or augmented energy sources, especially when using traditional power sources, such as in wearable devices, remote locations, or mobile applications is not practical or cost-effective.
| S-EPMC10287749 | biostudies-literature