Structural optimization for heat detection of DNA thermosequencing platform using finite element analysis.
Ontology highlight
ABSTRACT:
SUBMITTER: Esfandyarpour H
PROVIDER: S-EPMC2719263 | biostudies-other | 2008 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The feasibility of determining biphasic material properties using a finite element model of stress relaxation coupled with two types of constrained optimization to match measured data was investigated. Comparison of these two approaches, a zero-order method and a gradient-based algorithm, validated the predicted material properties. Optimizations were started from multiple different initial guesses of material properties (design variables) to establish the robustness of the optimization. Overall, the optimal values are close to those found by Cohen et al. (1998) but these small differences produced a marked improvement in the fit to the measured stress relaxation. Despite the greater deviation in the optimized values obtained from the zero-order method, both optimization procedures produced material properties that gave equally good overall fits to the measured data. Furthermore, optimized values were all within the expected range of material properties. Modeling stress relaxation using the optimized material properties showed an excellent fit to the entire time history of the measured data.
| S-EPMC4286505 | biostudies-literature
Project description:Determination of time-weighted average (TWA) concentrations of volatile organic compounds (VOCs) in air using solid-phase microextraction (SPME) is advantageous over other sampling techniques, but is often characterized by insufficient accuracies, particularly at longer sampling times. Experimental investigation of this issue and disclosing the origin of the problem is problematic and often not practically feasible due to high uncertainties. This research is aimed at developing the model of the TWA extraction process and optimization of TWA air sampling by SPME using finite element analysis software (COMSOL Multiphysics, Burlington, MA, USA). It was established that sampling by porous SPME coatings with high affinity to analytes is affected by slow diffusion of analytes inside the coating, an increase of their concentrations in the air near the fiber tip due to equilibration, and eventual lower sampling rate. The increase of a fiber retraction depth (Z) resulted in better recoveries. Sampling of studied VOCs using 23 ga Carboxen/polydimethylsiloxane (Car/PDMS) assembly at maximum possible Z (40 mm) was proven to provide more accurate results. Alternative sampling configuration based on 78.5 × 0.75 mm internal diameter SPME liner was proven to provide similar accuracy at improved detection limits. Its modification with the decreased internal diameter from the sampling side should provide even better recoveries. The results obtained can be used to develop a more accurate analytical method for determination of TWA concentrations of VOCs in air using SPME. The developed model can be used to simulate sampling of other environments (process gases, water) by retracted SPME fibers.
| S-EPMC6278546 | biostudies-literature
Project description:Background and objectiveAn auditory prosthesis refers to a device designed to restore hearing. Some parameters of the auditory prosthesis, such as mass, implanted position, and degree, need to be repeatedly designed and optimized based on the realistic geometry of the ear. Numerous auditory prostheses designs were based on animal or specimen experiments involving many complex instruments, and the experimental specimens had low repeatability. The finite element method (FEM) can overcome these disadvantages and be carried out on the computer with substantial flexibility in modifying the prosthetic parameters to optimize them. This narrative review aims to analyze the recent advances in the design and optimization of auditory prostheses using the FEM and provides suggestions for future development.MethodsThe literature on the design of auditory prostheses using the FEM has been extensively studied using the PubMed and Web of Science databases, including different ear models and relevant parameters of different auditory prostheses that need to be designed and optimized.Key content and findingsThe process of designing and optimizing a prosthesis using the FEM includes building an ear model and a prosthesis model to simulate the implantation process. The related parameters of the prosthesis can be designed and modified conveniently. The post-implantation response could be used as an indicator to evaluate the prosthesis's performance.ConclusionsThe review concluded that the FEM had been widely studied in designing and optimizing middle ear implants and cochlear implants and obtained good results. FEM can be utilized to explore more effective directions for auditory prosthesis design and optimization in the future.
| S-EPMC9279791 | biostudies-literature
Project description:Aortic vascular graft infections have high morbidity and mortality rate, however, patients often do not show symptoms. Continuous implant surface monitoring will allow for early detection of infections on implant surfaces, which allows for antibiotic treatment prior to biofilm formation. We explore the possibility of using heat flux sensors mounted on an aortic vascular graft to sense the localized heat production at the onset of infectious growth. We apply Finite Element Model simulations to demonstrate changes of the heat transfer coefficient depending on different pulsatile flow parameters. We determine various differences, the main influence being the distance travelled from the inlet of the simulation with the highest heat transfer coefficient closest to the inlet and decreasing along the direction of travel of the fluid. The determined range of heat transfer coefficients of 200 to 4800 W/m2 was applied to a second simulation of the thermal environment of the implant. We determined the heat transfer efficiency of the aortic graft system depending on different graft materials and thicknesses. We are further able to determine that the early detection of infection is possible by comparing the simulated amount of heat flux produced locally with the resolution of a commercial heat flux sensor.
| S-EPMC10533875 | biostudies-literature
Project description:Optimal tip sonication settings, namely tip position, input power, and pulse durations, are necessary for temperature sensitive procedures like preparation of viable cell extract. In this paper, the optimum tip immersion depth (20-30% height below the liquid surface) is estimated which ensures maximum mixing thereby enhancing thermal dissipation of local cavitation hotspots. A finite element (FE) heat transfer model is presented, validated experimentally with (R2 > 97%) and used to observe the effect of temperature rise on cell extract performance of E. coli BL21 DE3 star strain and estimate the temperature threshold. Relative yields in the top 10% are observed for solution temperatures maintained below 32°C; this reduces below 50% relative yield at temperatures above 47°C. A generalized workflow for direct simulation using the COMSOL code as well as master plots for estimation of sonication parameters (power input and pulse settings) is also presented.
| S-EPMC9161774 | biostudies-literature
Project description:A microfluidic platform for hydrodynamic electrochemical analysis was developed, consisting of a poly(methyl methacrylate) chip and three removable electrodes, each housed in 1/16" OD polyether ether ketone tube which can be removed independently for polishing or replacement. The working electrode was a 100-μm diameter Pt microdisk, located flush with the upper face of a 150 μm × 20 μm × 3 cm microchannel, smaller than previously reported for these types of removable electrodes. A commercial leak-less reference electrode was utilized, and a coiled platinum wire was the counter electrode. The platform was evaluated electrochemically by oxidizing a potassium ferrocyanide solution at the working electrode, and a typical limiting current behavior was observed after running linear sweep voltammetry and chronoamperometry, with flow rates 1-6 μL/min. While microdisk channel electrodes have been simulated before using a finite difference method in an ideal 3D geometry, here we predict the limiting current using finite elements in COMSOL Multiphysics 5.3a, which allowed us to easily explore variations in the microchannel geometry that have not previously been considered in the literature. Experimental and simulated currents showed the same trend but differed by 41% in simulations of the ideal geometry, which improved when channel and electrode imperfections were included.
| S-EPMC6656400 | biostudies-literature
Project description:Prior studies show vertebral strength from computed tomography-based finite element analysis may be associated with vertebral fracture risk. We found vertebral strength had a strong association with new vertebral fractures, suggesting that vertebral strength measures identify those at risk for vertebral fracture and may be a useful clinical tool.IntroductionWe aimed to determine the association between vertebral strength by quantitative computed tomography (CT)-based finite element analysis (FEA) and incident vertebral fracture (VF). In addition, we examined sensitivity and specificity of previously proposed diagnostic thresholds for fragile bone strength and low BMD in predicting VF.MethodsIn a case-control study, 26 incident VF cases (13 men, 13 women) and 62 age- and sex-matched controls aged 50 to 85 years were selected from the Framingham multi-detector computed tomography cohort. Vertebral compressive strength, integral vBMD, trabecular vBMD, CT-based BMC, and CT-based aBMD were measured from CT scans of the lumbar spine.ResultsLower vertebral strength at baseline was associated with an increased risk of new or worsening VF after adjusting for age, BMI, and prevalent VF status (odds ratio (OR) = 5.2 per 1 SD decrease, 95% CI 1.3-19.8). Area under receiver operating characteristic (ROC) curve comparisons revealed that vertebral strength better predicted incident VF than CT-based aBMD (AUC = 0.804 vs. 0.715, p = 0.05) but was not better than integral vBMD (AUC = 0.815) or CT-based BMC (AUC = 0.794). Additionally, proposed fragile bone strength thresholds trended toward better sensitivity for identifying VF than that of aBMD-classified osteoporosis (0.46 vs. 0.23, p = 0.09).ConclusionThis study shows an association between vertebral strength measures and incident vertebral fracture in men and women. Though limited by a small sample size, our findings also suggest that bone strength estimates by CT-based FEA provide equivalent or better ability to predict incident vertebral fracture compared to CT-based aBMD. Our study confirms that CT-based estimates of vertebral strength from FEA are useful for identifying patients who are at high risk for vertebral fracture.
| S-EPMC6450770 | biostudies-literature
Project description:This study aimed to evaluate fatigue of three stent designs when various forces are applied and perform a comparative analyses. A computer simulation using the finite element method was performed. In particular, we constructed a three-dimensional finite element model of nitinol stents with three designs (S6: single-woven wire, wire diameter: 0.006 inch; D6: double-woven wire, wire diameter: 0.006 inch, and D7: double-woven wire, wire diameter: 0.007 inch) that are used to treat canine tracheal collapse (TC). The stents were subjected to a 200 mmHg compression force, a pure torsion force in a perpendicular direction, and a bending-torsion force combining perpendicular and axial forces. The von Mises stress was calculated to evaluate the extent of stent displacement, and Goodman diagrams were plotted to compare fatigue life cycles. D7 exhibited a longer fatigue life compared to S6 and D6. Under compression, pure torsion, and bending-torsion forces, displacement was the smallest for D7, followed by D6 and S6. Similarly, the fatigue life was the longest for D7, followed by D6 and S6. S6 showed the greatest displacement when subjected to external forces; among stents designed using the same wire, D6 displayed less displacement than S6, and D7 exhibited superior fatigue life when subjected to varying degrees of force. This study showed that the structural stability and fatigue life of stents could be effectively compared using finite element method D7 has the greatest stability and structural rigidity under cyclic load.
| S-EPMC10882158 | biostudies-literature
Project description:Considering necessary fundamental and structural changes in the production and manufacturing industries to fulfill the industry 4.0 paradigm, the proposal of new ideas and frameworks for operations management of production and manufacturing system is inevitable. This research focuses on traditional methods proposed for storage assignment problem and struggles for new methods and definitions for industry 4.0 based storage assignment concepts. At the first step, the paper proposes a new definition of storage assignment and layout problem for fulfilling storage mechanism agility in terms of automated store and retrieval process (AS/RS) in modern inventories. Then considering the shortcomings of traditional algorithms for storage assignment problem, the paper contributes a new algorithm called SAO/FEM (storage assignment optimization technique), inspired from mechanical engineering discipline for analysis and optimization of storage assignment problem. The proposed new algorithm about stress distribution analogy, and the help of the Finite Element Method and minimum total potential energy theory, proposes a new model for storage assignment optimization. The efficiency of the proposed algorithm in terms of calculation time and the best answer investigated through numerical examples. The article has developed an application for SAO/FEM algorithm as a value creation module and applied new optimized storage positioning in the warehouses.
| S-EPMC7959603 | biostudies-literature
Project description:BackgroundDental biomechanics based on finite element (FE) analysis is attracting enormous interest in dentistry, biology, anthropology and palaeontology. Nonetheless, several shortcomings in FE modeling exist, mainly due to unrealistic loading conditions. In this contribution we used kinematics information recorded in a virtual environment derived from occlusal contact detection between high resolution models of an upper and lower human first molar pair (M1 and M1, respectively) to run a non-linear dynamic FE crash colliding test.MethodologyMicroCT image data of a modern human skull were segmented to reconstruct digital models of the antagonistic right M1 and M1 and the dental supporting structures. We used the Occlusal Fingerprint Analyser software to reconstruct the individual occlusal pathway trajectory during the power stroke of the chewing cycle, which was applied in a FE simulation to guide the M1 3D-path for the crash colliding test.ResultsFE analysis results showed that the stress pattern changes considerably during the power stroke, demonstrating that knowledge about chewing kinematics in conjunction with a morphologically detailed FE model is crucial for understanding tooth form and function under physiological conditions.Conclusions/significanceResults from such advanced dynamic approaches will be applicable to evaluate and avoid mechanical failure in prosthodontics/endodontic treatments, and to test material behavior for modern tooth restoration in dentistry. This approach will also allow us to improve our knowledge in chewing-related biomechanics for functional diagnosis and therapy, and it will help paleoanthropologists to illuminate dental adaptive processes and morphological modifications in human evolution.
| S-EPMC4816422 | biostudies-literature