Biomechanical stability of four fixation constructs for distal radius fractures.
Ontology highlight
ABSTRACT:
SUBMITTER: Capo JT
PROVIDER: S-EPMC2724612 | biostudies-other | 2009 Sep
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The purpose of this study was to compare the biomechanical properties of four volar fixed-angle fracture fixation plate designs in a novel sawbones model as well as in cadavers. Four volar fixed angle plating systems (Hand Innovations DVR-A, Avanta SCS/V, Wright Medical Lo-Con VLS, and Synthes stainless volar locking) were tested on sawbones models using an osteotomy gap model to simulate a distal radius fracture. Based on a power analysis, six plates from each system were tested to failure in axial compression. To simulate loads with physiologic wrist motion, six plates of each type were then tested to failure following 10,000 cycles applying 100N of compression. To compare plate failure behavior, two plates of each type were implanted in cadaver wrists and similar testing applied. All plate constructs were loaded to failure. All failed with in apex volar angulation. The Hand Innovations DVR-A plate demonstrated significantly more strength in peak load to failure and failure after fatigue cycling (p value < 0.001 for single load and fatigue failure). However, there was no significant difference in stiffness among the four plates in synthetic bone. The cadaveric model demonstrated the same mode of failure as the sawbones. None of the volar plates demonstrated screw breakage or pullout, except the tine plate (Avanta SCS/V) with 1 mm of pullout in 2 of 12 plates. This study demonstrates the utility of sawbones in biomechanical testing and indicates that volar fixation of unstable distal radius fractures with a fixed angle device is a reliable means of stabilization.
| S-EPMC2529136 | biostudies-other
Project description:To compare the static and dynamic mechanical properties of a modified crossed cannulated screw (CS) configuration, the inverted triangle (IT) cannulated screw configuration, and a compression hip screw (CHS) with derotation screw in Pauwels type III femoral neck fractures.Thirty synthetic femora were divided into 3 groups, and vertical femoral neck osteotomies were made. Ten osteotomized femora were fixed with a CS configuration, 10 were fixed with 3 parallel screws in an IT configuration, and the remaining 10 osteotomized femora were fixed with a CHS construct. All groups were tested using a cyclic (up to 15,000 load cycles) axial loading protocol, and survivors were statically loaded to failure. Cycles to failure, load to failure, and stiffness were calculated. The Kaplan-Meier method was used to estimate survival functions and were compared among fixation methods. The relationship between construct structural properties (maximum load and stiffness) and treatment were assessed using general linear modeling.All CHS fixation constructs survived the 15,000 cycle loading protocol. They endured longer (P = 0.034) than the CS fixation constructs (mean failure 13,332 cycles), but were not different from IT fixation constructs (mean failure 13,592 cycles). Maximum loads to failure for CS (3870 N) and IT (3756 N) fixation constructs were not different, but were less (P < 0.0001) than the maximum loads to failure for the CHS fixation constructs (5654 N). These findings parallel the results of the axial stiffness measurements: CS fixation constructs (663.01 N/mm) were not stiffer than IT fixation constructs (620.0 N/mm), but were less (P = 0.0005) than the axial stiffness of the CHS fixation constructs (1241.86 N/mm).The biomechanical performance of the CHS fixation method was superior to both the CS fixation method and the IT fixation method using a synthetic femoral model and this test protocol. Biomechanical performance of the latter 2 groups was indistinguishable. We recommend the use of CHS with the derotational screw construct for Pauwels III femoral neck fractures whenever possible.
| S-EPMC6137809 | biostudies-literature
Project description:Background Unstable distal ulna fractures in the setting of distal radius fractures can present a challenging problem, especially in the elderly population. Operative fixation of the subcapital distal ulna fracture may help to provide a stable ulnar buttress for attempting to reduce the distal radius fracture. Traditional fixation techniques of the distal ulna may prove unsatisfactory in the setting of osteoporosis and comminution. Description The intrafocal pin plate is placed through a small incision distally and uses the curve of the plate to obtain multiple points of fixation within the intramedullary canal. The overhang of the distal aspect of the plate helps to reduce the fracture. The plate is secured using unicortical locking screws in the ulnar head. Patients and Methods The most ideal fracture pattern for this fixation technique is a subcapital distal ulna fracture that is unstable and associated with a distal radius fracture. This technique is contraindicated in ulnar head fractures, segmental fractures with proximal extension, and open fractures with gross contamination as well as in the setting of active infection. Results This technique has provided a stable ulnar buttress and aided in the reduction of grossly unstable distal radius fractures. All of these patients have gone on to union, and we have not experienced a need for plate removal due to pain or soft tissue irritation. Conclusions We have found the intrafocal pin plate to provide both a stable ulnar buttress as well as intramedullary fixation to aid in the fixation of distal radius fractures associated with unstable distal ulna subcapital fractures.
| S-EPMC3922842 | biostudies-other
Project description:PURPOSE: Fixed-angle devices have been a major advancement in orthopedic fracture care and have become an attractive option for fixation of distal radius fractures. Several volar locking plates exist, but there is insufficient literature comparing the strengths of these plates. This study compares the biomechanical strength of two popular volar locking plate systems (Synthes LCP and Hand Innovations DVR-A) along with a nonlocking volar T-plate (Synthes). METHODS: Twenty-three formalin-fixed cadaveric forearms were divided into three groups with similar ages and bone densities. An unstable extra-articular fracture was created using a standardized osteotomy. Each group was fixed with one of the three plates. Each specimen was loaded in axial compression for 2000 cycles at a force of 400 N. Each specimen that completed cyclic testing was loaded to failure. Stiffness, yield point, and ultimate strength were recorded for each construct. RESULTS: Each fixed-angle construct completed all 2000 cycles. The nonlocking plates failed at an average of 560 cycles. The mean stiffness of the DVR-A, LCP, and the volar T-plates were 277.00, 343.17, and 175.67 N/mm, respectively. There was a statistically significant difference between both fixed-angle plates and the nonlocking plate (p < 0.05). The difference between each fixed-angle construct did not reach significance. Yield point and ultimate strength could only be determined for the two fixed-angle devices. There was no statistically significant difference between the constructs for both yield point (DVR-A = 855.56 N, LCP = 894.15 N) and ultimate strength (DVR-A = 1,021.97 N, LCP = 1,114.87 N). CONCLUSIONS: Given our data, fixed-angle constructs withstand cyclical loading representing normal physiologic forces encountered during post-operative rehabilitation. There was no significant biomechanical difference between the two fixed-angle constructs. Our results support that volar fixed-angle locking plates are an effective treatment for unstable extra-articular distal radius fractures, allowing early postoperative rehabilitation to safely be initiated.
| S-EPMC2528971 | biostudies-other
Project description:This article is a systematic review of the recent published literature on the biomechanics of volar locking plate fixation of distal radius fractures. PUBMED/MEDLINE and EMBASE databases were searched on 13th Sep 2018. Biomechanical papers on volar locking plate fixation of distal radius fractures since 2010 were included. Papers were analysed and included studies were appraised by the author using the validated quality assessment GRADE tool. The search revealed 456 papers between January 2010 and the present day whose abstracts were reviewed for relevance and 21 papers were included for full paper review. The aim of this systematic review was to evaluate the evidence to determine the surgical techniques and strategies that are associated with the best biomechanical outcomes of volar plating for distal radius fractures. Review of the literature revealed that it was not necessary to fill all available distal locking screws, there was little evidence to support the use of 2 rows of screws distally over 1 row. Screws of 75% length of the distal cortex are sufficient to withstand standard postoperative regimes in extrarticular fractures. The was a paucity of evidence to conclude multidirectional locking plates were superior to fixed angle plates or that one brand of plate was superior to another.
| S-EPMC6739430 | biostudies-literature
Project description:BACKGROUND AND PURPOSE: There is no consensus on the difference in effects of internal fixation (IF) and external fixation (EF) on outcomes for the treatment of distal radius fractures. We performed a meta-analysis of randomized clinical studies. METHODS: We searched the literature and included studies that compared the effects of IF and EF on the treatment of distal radius fractures. Statistically, we pooled patient data using standard meta-analytic methods. For the continuous variables, the weighted mean difference (WMD) was used. For dichotomous data, the relative risk (RR) was calculated. RESULTS: 10 studies were eligible for data extraction. The pooled data showed that compared with EF, IF led to statistically significantly better Disabilities of the Arm, Shoulder, and Hand (DASH) scores at 12 months postoperatively, recovery of forearm supination at 3 months, and restoration of volar tilt and radial inclination. IF using volar locking plates resulted in better DASH scores than EF at 3 and 6 months, but the trend diminished over time; at 12 months postoperatively, the scores were not statistically significant. Compared with EF, IF led to fewer minor surgical complications. INTERPRETATION: For surgical treatment of distal radius fractures, IF yields better functional outcomes, forearm supination, restoration of anatomic volar tilt and radial inclination, and fewer minor complications. The patients who received IF using volar locking plates for the treatment of distal radius recovered more quickly than did patients who received EF.
| S-EPMC3715819 | biostudies-other
Project description:IntroductionOptimal management of distal radius fractures in adults remains controversial. Previous evidence and current clinical guidelines tell us that, if a closed reduction of a dorsally displaced fracture is possible, Kirschner wires (K-wires) are the preferred form of surgical fixation. However, the question remains whether there is any need to perform surgical fixation following a successful closed reduction, or is a simple plaster cast as effective? This is the protocol for a randomised controlled trial of manipulation and surgical fixation with K-wires versus manipulation and casting in the treatment of dorsally displaced distal radius fractures.Methods and analysisAdult patients with an acute dorsally displaced fracture of the distal radius are potentially eligible to take part. Prior to surgery, baseline demographic data, radiographs, data on pain/function using the Patient-Rated Wrist Evaluation Score (PRWE) and health-related quality of life (HRQoL) using the EuroQoL 5-dimension 5-level (EQ-5D-5L) will be collected. A randomisation sequence, stratified by centre, intra-articular extension of the fracture and age, will be administered via a secure web-based service. Each patient will be randomly allocated to either 'manipulation and surgical fixation with K-wires' or 'manipulation and plaster casting'. A clinical assessment, radiographs and records of early complications will be recorded at 6 weeks. PRWE and HRQoL outcome data will be collected at 3, 6 and 12 months post-randomisation. Further information will be requested with regard to healthcare resource use and any complications.Ethics and disseminationThe National Research Ethic Committee approved this study on 6 October 2016 (16/SC/0462).The National Institute for Health Research Health Technology Assessment monograph and a manuscript to a peer-reviewed journal will be submitted on completion of the trial. The results of this trial will substantially inform clinical practice on the clinical and cost-effectiveness of the treatment of this injury.Trial registration numberISRCTN11980540; Pre-results.
| S-EPMC6475232 | biostudies-literature
Project description:Background and purpose - The reliability of conventional radiography when classifying distal radius fractures (DRF) is fair to moderate. We investigated whether reliability increases when additional computed tomography scans (CT) are used. Patients and methods - In this prospective study, we performed pre- and postreduction posterior-anterior and lateral radiographs of 51 patients presenting with a displaced DRF. The case was included when there was a (questionable) indication for surgical treatment and an additional CT was conducted within 5 days. 4 observers assessed the cases using the Frykman, Fernández, Universal, and AO classification systems. The first 2 assessments were performed using conventional radiography alone; the following 2 assessments were performed with an additional CT. We used the intraclass correlation coefficient (ICC) to evaluate reliability. The CT was used as a reference standard to determine the accuracy. Results - The intraobserver ICC for conventional radiography alone versus radiography and an additional CT was: Frykman 0.57 vs. 0.51; Fernández 0.53 vs. 0.66; Universal 0.57 vs. 0.64; AO 0.59 vs. 0.71. The interobserver ICC was: Frykman: 0.45 vs. 0.28; Fernández: 0.38 vs. 0.44; Universal: 0.32 vs. 0.43; AO: 0.46 vs. 0.40. Interpretation - The intraobserver reliability of the classification systems was fair but improved when an additional CT was used, except for the Frykman classification. The interobserver reliability ranged from poor to fair and did not improve when using an additional CT. Additional CT scanning has implications for the accuracy of scoring the fracture types, especially for simple fracture types.
| S-EPMC5694815 | biostudies-literature
Project description:Four cases of flexor tendon problems which developed after volar plate fixation of distal radius fractures are presented. All cases were associated with close contact of the screws or distal edge of the plate with the flexor tendons. Poor bone stock or multiple bone fragments allowing loosening of the plate or non-locking screws cause the hardware to irritate the flexor tendons and ultimately lead to rupture. The flexor tendons involved include the flexor carpi radialis, flexor pollicis longus and flexor digitorum superficialis, and flexor digitorum profundus to the index and long fingers.
| S-EPMC2787213 | biostudies-other
Project description:PURPOSE:Displaced distal radius fractures in children are common and often treated by reduction and cast immobilization. Redisplacement occurs frequently and may be prevented by additional treatment with K-wire fixation after initial reduction. This meta-analysis aims to summarize available literature on this topic and determine if primary K-wire fixation is the preferred treatment for displaced distal radius fractures in children. METHODS:A search in eight databases identified studies that compared cast immobilization alone to additional K-wire fixation as treatment for displaced paediatric distal radius fractures. The primary outcome was the redisplacement rate. Secondary outcomes were secondary reduction rate, range of motion and complications. This meta-analysis was performed according to the preferred reporting items for systematic reviews and meta-analysis (PRISMA) statement. RESULTS:Three RCTs and 3 cohort studies, analysing 197 patients treated with cast immobilization alone and 185 with additional K-wire fixation, were included in this meta-analysis. Redisplacement occurred less frequently after additional K-wire fixation than after cast alone (3.8 versus 45.7%; OR 0.07, 95% CI 0.03-0.15). Secondary reduction was performed in 59.8% of the redisplaced fractures. Complications, other than redisplacement, occurred more often after additional K-wire fixation than after cast alone (15.7 versus 3.6%). Range of motion did not differ after both treatments. CONCLUSIONS:Additional K-wire fixation is a suitable treatment to prevent redisplacement and secondary operations after initial reduction of displaced distal radius fractures in children, but is associated with post-procedural complications. Additional K-wire fixation does not result in a better range of motion than cast immobilization alone. More research is needed to identify those patients who will benefit the most from K-wire fixation as a treatment for displaced distal radius fractures in children.
| S-EPMC6910898 | biostudies-literature