Effect of sintering conditions on the magnetic and microstructural properties of Nd-Fe-B sintered magnets doped with DyF(3) powders.
Ontology highlight
ABSTRACT:
SUBMITTER: Park SE
PROVIDER: S-EPMC3298553 | biostudies-other | 2012 Apr
REPOSITORIES: biostudies-other
Similar Datasets
Project description:The grain boundary diffusion process (GBDP) has become an important technique in improving the coercivity and thermal stability of Dy-free sintered Nd-Fe-B magnets. The influence of Dy70Al10Ga20 and (Pr75Dy25)70Al10Ga20 alloys by the GBDP on sintered Nd-Fe-B magnets are investigated in this paper. After diffusing Dy70Al10Ga20 and (Pr75Dy25)70Al10Ga20 alloys, the coercivity (Hcj) of the magnets increased from 13.58 kOe to 20.10 kOe and 18.11 kOe, respectively. Meanwhile, the remanence of the magnets decreased slightly. The thermal stability of the diffused magnets was improved by the GBDP. The microstructure shows continuous Rare-earth-rich (RE-rich) grain boundary phases and (Dy, Pr/Nd)2Fe14B core-shell structures which contribute to improving the coercivity. Moreover, the Dy concentration on the surface of the (Pr75Dy25)70Al10Ga20 diffused magnets decreased with the Pr substitution for the Dy element. The openness of the recoil loops for the (Pr75Dy25)70Al10Ga20 diffused magnets is smaller than that of the original magnets and Dy70Al10Ga20 diffused magnets. The results show that the (Pr75Dy25)70Al10Ga20 alloys can effectively optimize the microstructure and improve the magnetic properties and thermal stability of the sintered Nd-Fe-B magnets.
| S-EPMC8156186 | biostudies-literature
Project description:Recycling of end-of-life Nd-Fe-B magnets is an important strategy for reducing the environmental dangers associated with rare-earth mining and overcoming the supply risks associated with the rare-earth elements. In this study, a novel concept for recycling of sintered Nd-Fe-B magnets by directly recovering the matrix Nd2 Fe14 B grains is presented. The procedure is based on the anodic etching of sintered Nd-Fe-B magnets in a nonaqueous dimethylformamide (DMF)/0.3?mol?L-1 FeCl2 bath. Selective recovery of Nd2 Fe14 B grains was realized within the applied current density <5?mA?cm-2 based on the etching priority of phases: metallic Nd > intergranular NdFe4 B4 > matrix Nd2 Fe14 B. The total energy consumption of the proposed recycling route is estimated to be 2.99?kWh?kg-1 , which is comparable to the state-of-the-art methods. However, the proposed recycling route is currently the only procedure that enables repeated recycling of sintered Nd-Fe-B magnets in a closed-loop system.
| S-EPMC6916163 | biostudies-literature
Project description:Magnetic two-dimensional materials have attracted considerable attention for their significant potential application in spintronics. In this study, we present a high-quality Fe-doped SnS2 monolayer exfoliated using a micromechanical cleavage method. Fe atoms were doped at the Sn atom sites, and the Fe contents are ?2.1%, 1.5%, and 1.1%. The field-effect transistors based on the Fe0.021Sn0.979S2 monolayer show n-type behavior and exhibit high optoelectronic performance. Magnetic measurements show that pure SnS2 is diamagnetic, whereas Fe0.021Sn0.979S2 exhibits ferromagnetic behavior with a perpendicular anisotropy at 2?K and a Curie temperature of ~31?K. Density functional theory calculations show that long-range ferromagnetic ordering in the Fe-doped SnS2 monolayer is energetically stable, and the estimated Curie temperature agrees well with the results of our experiment. The results suggest that Fe-doped SnS2 has significant potential in future nanoelectronic, magnetic, and optoelectronic applications.
| S-EPMC5717146 | biostudies-literature
Project description:A facile synthesis of 3-6 nm, water dispersible, near-infrared (NIR) emitting, quantum dots (QDs) magnetically doped with Fe is presented. Doping of alloyed CdTeS nanocrystals with Fe was achieved in situ using a simple hydrothermal method. The magnetic quantum dots (MQDs) were capped with NAcetyl-Cysteine (NAC) ligands, containing thiol and carboxylic acid functional groups to provide stable aqueous dispersion. The optical and magnetic properties of the Fe doped MQDs were characterized using several techniques. The synthesized MQDs are tuned to emit in the Vis-NIR (530-738 nm) wavelength regime and have high quantum yields (67.5-10%). NIR emitting (738 nm) MQDs having 5.6 atomic% Fe content exhibited saturation magnetization of 85 emu/gm[Fe] at room temperature. Proton transverse relaxivity of the Fe doped MQDs (738 nm) at 4.7 T was determined to be 3.6 mM-1s-1. The functional evaluation of NIR MQDs has been demonstrated using phantom and in vitro studies. These water dispersible, NIR emitting and MR contrast producing Fe doped CdTeS MQDs, in unagglomerated form, have the potential to act as multimodal contrast agents for tracking live cells.
| S-EPMC3947824 | biostudies-literature
Project description:In the drive to reduce the critical Heavy Rare Earth (HRE) content of magnets for green technologies, HRE-free Nd-Fe-B has become an attractive option. HRE is added to Nd-Fe-B to enhance the high temperature performance of the magnets. To produce similar high temperature properties without HRE, a crystallographically textured nanoscale grain structure is ideal; and this conventionally requires expensive "die upset" processing routes. Here, a Flash Spark Plasma Sintering (FSPS) process has been applied to a Dy-free Nd30.0Fe61.8Co5.8Ga0.6Al0.1B0.9 melt spun powder (MQU-F, neo Magnequench). Rapid sinter-forging of a green compact to near theoretical density was achieved during the 10?s process, and therefore represents a quick and efficient means of producing die-upset Nd-Fe-B material. The microstructure of the FSPS samples was investigated by SEM and TEM imaging, and the observations were used to guide the optimisation of the process. The most optimal sample is compared directly to commercially die-upset forged (MQIII-F) material made from the same MQU-F powder. It is shown that the grain size of the FSPS material is halved in comparison to the MQIII-F material, leading to a 14% increase in coercivity (1438?kA?m-1) and matched remanence (1.16?T) giving a BHmax of 230?kJ?m-3.
| S-EPMC5593872 | biostudies-other
Project description:The low cost, rare earth free ?-phase of MnAl has high potential to partially replace bonded Nd2Fe14B rare earth permanent magnets. However, the ?-phase is metastable and it is experimentally difficult to obtain powders suitable for the permanent magnet alignment process, which requires the fine powders to have an appropriate microstructure and high ?-phase purity. In this work, a new method to make high purity ?-phase fine powders is presented. A high purity ?-phase Mn0.55Al0.45C0.02 alloy was synthesized by the drop synthesis method. The drop synthesized material was subjected to cryo milling and followed by a flash heating process. The crystal structure and microstructure of the drop synthesized, cryo milled and flash heated samples were studied by X-ray in situ powder diffraction, scanning electron microscopy, X-ray energy dispersive spectroscopy and electron backscatter diffraction. Magnetic properties and magnetic structure of the drop synthesized, cryo milled, flash heated samples were characterized by magnetometry and neutron powder diffraction, respectively. The results reveal that the 2 and 4?hours cryo milled and flash heated samples both exhibit high ?-phase purity and micron-sized round particle shapes. Moreover, the flash heated samples display high saturation magnetization as well as increased coercivity.
| S-EPMC5802788 | biostudies-literature
Project description:In the present study, high-purity ternary-phase nitride (Ti2AlN) powders were synthesized through microwave sintering using TiH2, Al, and TiN powders as raw materials. X-ray diffraction (XRD), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) were adopted to characterize the as-prepared powders. It was found that the Ti2AlN powder prepared by the microwave sintering of the 1TiH2/1.15Al/1TiN mixture at 1250 °C for 30 min manifested great purity (96.68%) with uniform grain size distribution. The formation mechanism of Ti2AlN occurred in four stages. The solid-phase reaction of Ti/Al and Ti/TiN took place below the melting point of aluminum and formed Ti2Al and TiN0.5 phases, which were the main intermediates in Ti2AlN formation. Therefore, the present work puts forward a favorable method for the preparation of high-purity Ti2AlN powders.
| S-EPMC7728301 | biostudies-literature
Project description:We have investigated the influence of multiple scattering on the magnetic small-angle neutron scattering (SANS) from a Nd-Fe-B nanocrystalline magnet. We performed sample-thickness- and neutron-wavelength-dependent SANS measurements, and observed the scattering vector dependence of the multiple magnetic scattering. It is revealed that significant multiple scattering exists in the magnetic scattering rather than the nuclear scattering of Nd-Fe-B nanocrystalline magnet. It is considered that the mean free path of the neutrons for magnetic scattering is rather short in Nd-Fe-B magnets. We analysed the SANS data by the phenomenological magnetic correlation model considering the magnetic microstructures and obtained the microstructural parameters.
| S-EPMC4913308 | biostudies-other
Project description:Three phases can be distinguished in Nd?Fe?B permanent magnets: a Nd2Fe14B matrix grain phase, a Nd-rich grain boundary phase and a Nd-oxide phases. Common reaction models for leaching, such as the shrinking-particle model, cannot simply be applied to composite Nd?Fe?B permanent magnets because of the different chemical reactivities of the crystalline phases mentioned above. Etching the surface of a Nd?Fe?B magnet to expose its microstructure to electron microscopy is a necessary practice to correlate the microstructure itself to the specific properties of the magnets. Aqueous solutions of mineral acids are often used for etching purposes. However, these solutions are too low viscous to easily control the etching front and they show little selectivity in the etching process. In our work, the ionic liquid Cyphos IL 101 was used to etch bulk magnets instead of aqueous HCl solutions. The bulk Nd?Fe?B magnets were first polished, then exposed to a solution of 3 M HCl in Cyphos IL 101 for different times and at different temperatures. Afterwards, the etched Nd?Fe?B magnets were washed with ethanol and acetone. The results were examined via scanning-electron microscopy and image analysis. A commercial software, ImageJ®, was employed for image analysis. The latter technique was used to correlate the etched area (%area) or the grain and oxide size to the etching temperature or the etching time. The grain or the oxide size were calculated as Feret diameter. Image analysis revealed to be a necessary tool to support and correct the findings first suggested by the simple scanning-electron microscopy. The data presented in this article might be reused to corroborate a new reactivity order of the three Nd?Fe?B phases, different from that traditionally reported in literature, which is - from the most to the least reactive - grain boundary > oxides > the Nd2Fe14B grain phase.
| S-EPMC7452628 | biostudies-literature
Project description:Fe-doped LiNbO₃ synthesized by the combustion method to seek new multiferroic materials exhibits room-temperature ferromagnetism, as reported in our previous work [1]. In this work, the defect structure of congruent and Fe-doped LiNbO₃ (0.57-3.3 mol %) powders was investigated in detail by several methods. The molar ratio of [Li]/([Li]+[Nb]) was determined by the Curie temperature (Tc) via DSC. Two peaks of Tc were observed due to phase splitting [2], and the phase at lower Tc disappears as the Fe doping concentration increases. The coexistence of two different oxidation states of Fe ions in LiNbO₃ was probed by XPS and UV-Vis spectroscopy. The Raman spectra exhibit displacements along the c axis of Li and Nb ions, and a deformation of the NbO₆ framework owing to Fe doping. Several doping models were applied in the Rietveld refinement of powder X-ray diffraction collected by synchrotron radiation. The fitting by the Nb vacancy model leads to an improbably distorted structure of congruent LiNbO₃. In Fe-doped LiNbO₃, we conjecture that Li and Nb vacancies coexist in the lattice structure; Fe+2/Fe+3 ions are substituted for Li ions at the regular Li site and may push the anti-site NbLi ion back to the regular Nb site.
| S-EPMC5506989 | biostudies-other