One step high quality poly(dimethylsiloxane)-hydrocarbon plastics bonding.
Ontology highlight
ABSTRACT:
SUBMITTER: Xu BY
PROVIDER: S-EPMC3370403 | biostudies-other | 2012 Mar
REPOSITORIES: biostudies-other
Similar Datasets
Project description:Poly(dimethylsiloxane)-block-methoxypolyethylene glycols (PDMS-b-mPEG) were synthesized by Steglich esterification. The high-permeable membrane (PSf/PDMS-b-mPEG) was prepared by using PDMS-b-mPEG as additives. The successful synthesis of PDMS-b-mPEG was confirmed by nuclear magnetic resonance. Field emission scanning electron microscopy images show that the distribution of finger-like macroporous and sponge-like macroporous can be modulated by controlling the ratio of the hydrophilic/hydrophobic components of additives. The distribution of additives and membrane wettability are validated with X-ray photoelectron spectroscopy and water contact angle test. The permeability of the blended membrane, especially for the membrane PSf/PDMS-b-mPEG1900 (M3), was remarkably improved. The water permeability of M3 (239.4 L/m2·h·bar) was 6.6 times that of the unblended membrane M0 (42.5 L/m2·h·bar). The findings of protein BSA filtration show that the flux recovery ratio of M3 is 89.2% at a BSA retention rate of about 80%, which demonstrates that the polysulfone membranes blended with PDMS-b-mPEG have excellent antifouling performance and extraordinary permeability.
| S-EPMC6704433 | biostudies-literature
Project description:Ethylene production from C2 hydrocarbon mixtures through one separation step is desirable but challenging because of the similar size and physical properties of acetylene, ethylene, and ethane. Herein, we report three new isostructural porous coordination networks (NPU-1, NPU-2, NPU-3; NPU represents Northwestern Polytechnical University) that are sustained by 9-connected nodes based upon a hexanuclear metal cluster of composition [Mn6(μ3-O)2(CH3COO)3]6+. NPU-1/2/3 exhibit a dual cage structure that was systematically fine-tuned in terms of cage size to realize selective adsorption of C2H2 and C2H6 over C2H4. Dynamic breakthrough experiments demonstrated that NPU-1 produces ethylene in >99.9% purity from a three-component gas mixture (1:1:1 C2H2/C2H4/C2H6). Molecular modeling studies revealed that the dual adsorption preference for C2H2 and C2H6 over C2H4 originates from (a) strong hydrogen-bonding interactions between electronegative carboxylate O atoms and C2H2 molecules in one cage and (b) multiple non-covalent interactions between the organic linkers of the host network and C2H6 molecules in the second cage.
| S-EPMC8297724 | biostudies-literature
Project description:In this study, we analyzed mutants of Clostridium acetobutylicum, an organism used in a broad range of industrial processes related to biofuel production, to facilitate future studies of bioreactor and bioprocess design and scale-up, which are very important research projects for industrial microbiology applications. To accomplish this, we generated 329 mutant strains and applied principal component analysis (PCA) to fermentation data gathered from these strains to identify a core set of independent features for comparison. By doing so, we were able to explain the differences in the mutant strains' fermentation expression states and simplify the analysis and visualization of the multidimensional datasets related to the strains. Our study has produced a high-efficiency PCA application based on a data analytics tool that is designed to visualize screening results and to support several hundred sets of data on fermentation interactions to assist researchers in more precisely screening and capturing high-quality mutant strains. More importantly, although this study focused on the use of PCA in microbial fermentation engineering, its results are broadly applicable.
| S-EPMC5206668 | biostudies-literature
Project description:Use of high-throughput sequencing (HTS) has become indispensable in life science research. Raw HTS data contains several sequencing artifacts, and as a first step it is imperative to remove the artifacts for reliable downstream bioinformatics analysis. Although there are multiple stand-alone tools available that can perform the various quality control steps separately, availability of an integrated tool that can allow one-step, automated quality control analysis of HTS datasets will significantly enhance handling large number of samples parallelly. Here, we developed HTSQualC, a stand-alone, flexible, and easy-to-use software for one-step quality control analysis of raw HTS data. HTSQualC can evaluate HTS data quality and perform filtering and trimming analysis in a single run. We evaluated the performance of HTSQualC for conducting batch analysis of HTS datasets with 322 samples with an average ~ 1 M (paired end) sequence reads per sample. HTSQualC accomplished the QC analysis in ~ 3 h in distributed mode and ~ 31 h in shared mode, thus underscoring its utility and robust performance. In addition to command-line execution, we integrated HTSQualC into the free, open-source, CyVerse cyberinfrastructure resource as a GUI interface, for wider access to experimental biologists who have limited computational resources and/or programming abilities.
| S-EPMC8455540 | biostudies-literature
Project description:The polymerization of octamethylcyclotetrasiloxane (D4) is investigated using several five-, six- and seven-membered N-heterocyclic carbenes (NHCs). The catalysts are delivered in situ from thermally susceptible CO2 adducts. It is demonstrated that the polymerization can be triggered from a latent state by mild heating, using the highly nucleophilic 1,3,4,5-tetramethylimidazol-2-ylidene as organocatalyst. This way, high molecular weight PDMS is prepared (up to >400 000 g/mol, 1.6 < Ð M < 2.5) in yields >95%, using low catalyst loadings (0.2-0.1 mol %). Furthermore, the results suggest that a nucleophilic, zwitterionic mechanism is in operation, in preference to purely anionic polymerization.
| S-EPMC4660969 | biostudies-literature
Project description:Hybrid microchannels composed of poly(dimethylsiloxane) and glass were coated with supported bilayer membranes (SBMs) by the process of vesicle fusion. The electroosmotic mobility (mu(eo)) of zwitterionic, positively charged, and negatively charged phospholipid membranes was measured over a 4 h time to evaluate the stability of the coatings in an electric field. Coated microchips with a simple cross design were used to separate the fluorescent dyes fluorescein and Oregon Green. Migration time reproducibility was better than 5% RSD over 70 min of continuous separations. Separation of Oregon Green and fluorescein in channels coated with zwitterionic phosphatidylcholine (PC) membranes yielded efficiencies of 611,000 and 499,000 plates/m and a resolution of 2.4 within 2 s. Both zwitterionic and negatively charged membranes were used to separate peptide substrates from their phosphorylated analogues with efficiencies of 200,000-400,000 plates/m. Notably, separations of fluorescently labeled ABL substrate peptide from its phosphorylated counterpart were achieved using a high-salt physiological buffer with near-baseline resolution in 10 s. PC-coated devices were used to successfully separate enhanced green fluorescent protein (eGFP) from a fusion protein (eGFP-Crakl) with an efficiency of 358,000 and 278,000 plates/m respectively in less than 12 s. These SBM-based coatings may enable the separation of a broad range of analytes and may be ideal in biological applications for microfluidics.
| S-EPMC2735572 | biostudies-literature
Project description:Soft, solvent-free poly(dimethylsiloxane) elastomers are fabricated by a one-step process via crosslinking bottlebrush polymers. The bottlebrush architecture prevents the formation of entanglements, resulting in elastomers with precisely controllable low moduli from 1 to 100 kPa, below the lower limit of traditional elastomers; moreover, the solvent-free nature enables their negligible adhesiveness compared to commercially available silicone products of similar stiffness.
| S-EPMC4662383 | biostudies-literature
Project description:Surface modifications of microfluidic devices are of essential importance for successful bioanalytical applications. Here, we investigate three different coatings for quartz and poly(dimethylsiloxane) (PDMS) surfaces. We employed a triblock copolymer with trade name F(108), poly(L-lysine)-g-poly(ethylene glycol) (PLL-PEG), as well as the hybrid coating n-dodecyl-?-D-maltoside and methyl cellulose (DDM/MC). The impact of these coatings was characterized by measuring the electroosmotic flow (EOF), contact angle, and prevention of protein adsorption. Furthermore, we investigated the influence of static coatings, i.e., the incubation with the coating agent prior to measurements, and dynamic coatings, where the coating agent was present during the measurement. We found that all coatings on PDMS as well as quartz reduced EOF, increased reproducibility of EOF, reduced protein adsorption, and improved the wettability of the surfaces. Among the coating strategies tested, the dynamic coatings with DDM/MC and F(108) demonstrated maximal reduction of EOF and protein adsorption and simultaneously best long-term stability concerning EOF. For PLL-PEG, a reversal in the EOF direction was observed. Interestingly, the static surface coating strategy with F(108) proved to be as effective to prevent protein adsorption as dynamic coating with this block copolymer. These findings will allow optimized parameter choices for coating strategies on PDMS and quartz microfluidic devices in which control of EOF and reduced biofouling are indispensable.
| S-EPMC3253858 | biostudies-literature
Project description:Growth factors have been shown to be potent mediators of osteogenesis. However, their use in tissue-engineered scaffolds not only can be costly but also can induce undesired responses in surrounding tissues. Thus, the ability to specifically induce osteogenic differentiation in the absence of exogenous growth factors through manipulation of scaffold material properties would be desirable for bone regeneration. Previous research indicates that addition of inorganic or hydrophobic components to organic, hydrophilic scaffolds can enhance multipotent stem cell (MSC) osteogenesis. However, the combined impact of scaffold inorganic content and hydrophobicity on MSC behavior has not been systematically explored, particularly in three-dimensional (3D) culture systems. The aim of the present study was therefore to examine the effects of simultaneous increases in scaffold hydrophobicity and inorganic content on MSC osteogenic fate decisions in a 3D culture environment toward the development of intrinsically osteoinductive scaffolds. Mouse 10T½ MSCs were encapsulated in a series of novel scaffolds composed of varying levels of hydrophobic, inorganic poly(dimethylsiloxane) (PDMS) and hydrophilic, organic poly(ethylene glycol) (PEG). After 21 days of culture, increased levels of osteoblast markers, runx2 and osteocalcin, were observed in scaffolds with increased PDMS content. Bone extracellular matrix (ECM) molecules, collagen I and calcium phosphate, were also elevated in formulations with higher PDMS:PEG ratios. Importantly, this osteogenic response appeared to be specific in that markers for chondrocytic, smooth muscle cell, and adipocytic lineages were not similarly affected by variations in scaffold PDMS content. As anticipated, the increase in scaffold hydrophobicity accompanying increasing PDMS levels was associated with elevated scaffold serum protein adsorption. Thus, scaffold inorganic content combined with alterations in adsorbed serum proteins may underlie the observed cell behavior.
| S-EPMC3419860 | biostudies-other
Project description:Poly(dimethylsiloxane) (PDMS) has been extensively used as an electroactive polymer material because it exhibits not only excellent moldability but also mechanical properties sufficient enough for electroactive performance despite low dielectric permittivity. Its low dielectric property is due to its molecular non-polarity. Here, we introduce a polar group into a PDMS elastomer by using vinyl acetate (VAc) as a crosslinker to improve the dielectric permittivity. We synthesized a high-molecular weight PDMS copolymer containing vinyl groups, namely poly(dimethylsiloxane-co-methylvinylsiloxane) (VPDMS), and prepared several of the VPDMS solutions in VAc. We obtained transparent PDMS films by UV curing of the solution layers. Electromechanical actuation-related physical properties of one of the UV-cured films were almost equivalent to or superior to those of platinum-catalyzed hydrosilylation-cured PDMS films. In addition, saponification of the UV-cured film significantly improved the electrical and mechanical properties (?' ~ 44.1 pF/m at 10 kHz, E ~ 350 kPa, ? ~ 320%). The chemical introduction of VAc into PDMS main chains followed by saponification would offer an efficacious method of enhancing the electroactive properties of PDMS elastomers.
| S-EPMC7697987 | biostudies-literature