Effective dose span of ten different cone beam CT devices.
Ontology highlight
ABSTRACT:
SUBMITTER: Rottke D
PROVIDER: S-EPMC3699973 | biostudies-other | 2013
REPOSITORIES: biostudies-other
Similar Datasets
Project description:OBJECTIVES: This study compares the effective dose for different fields of view (FOVs), resolutions and X-ray parameters from two cone beam CT units: the KaVo 3D (three-dimensional) eXam and the KaVo Pan eXam Plus 3D (KaVo Dental, Biberach, Germany). METHODS: Measurements were made using thermoluminescent dosemeter chips in a radiation analog dosimetry head and neck phantom. The calculations of effective doses are based on the ICRP 60 and ICRP 103 recommendations of the International Commission on Radiological Protection. RESULTS: Effective doses from the 3D eXam ranged between 32.8 µSv and 169.8 µSv, and for the Pan eXam Plus effective doses ranged between 40.2 µSv and 183.7 µSv; these were measured using ICRP 103 weighting factors in each case. The increase in effective dose between ICRP 60 and ICRP 103 recommendations averaged 157% for all measurements. CONCLUSIONS: Effective doses can be reduced significantly with the choice of lower resolutions and mAs settings as well as smaller FOVs to avoid tissues sensitive to radiation being inside the direct beam. Larger FOVs do not necessarily lead to higher effective doses.
| S-EPMC3635778 | biostudies-other
Project description:Background and purposeThe limited image quality in Cone Beam CT (CBCT) stemming primarily from scattered radiation hinders accurate CBCT based dose calculation in radiotherapy. We investigated the use of a stoichiometric calibration for dose calculation on CBCT images of lung cancer patients.Materials and methodsCBCT calibrations were performed with thorax scan protocols, using a phantom with approximately the diameter of an average human thorax and a central cavity simulating the thoracic cavity. Thus scatter conditions resembling those in clinical thorax CBCT scans were simulated. A published stoichiometric parametrization was used. A treatment plan was simulated on CBCT and CT scans of an anthropomorphic phantom, the dose distributions were calculated, and clinically relevant DVH parameters were compared. Twelve lung cancer patients had surveillance CT scans (s-CT) taken twice during their treatment course in addition to daily setup CBCTs. Dose calculations were performed on the s-CTs and the corresponding CBCTs taken on the same day, and DVH parameters were compared.ResultsEighty percent of CBCT DVH parameters found for the phantom were within ±1% of CT doses, and 98% were within ±3%. For patients, the median CT/CBCT dose difference was within ±2%, and 98% of DVH parameters were within ±4%. Minimum dose to the tumor was underestimated (median 1.9%) on CBCT, while maximum doses to most organs at risk were slightly overestimated.ConclusionDirect dose calculations on CBCTs of lung cancer patients were feasible within ∼4% accuracy using a simple calibration method, which is easily implemented in a clinical setting.
| S-EPMC7807659 | biostudies-literature
Project description:OBJECTIVES: To demonstrate the feasibility of GafChromic(®) XR-QA2 (ISP Corp., Wayne, NJ) as a dosemeter when performing measurements of the effective dose from three cone beam CT (CBCT) units and to compare the doses from examinations of three common dental clinical situations. A second aim was to compare the radiation doses for three digital panoramic units with the doses for the CBCT units. METHODS: The CBCT units used were Veraviewepocs 3De(®) (J Morita MFG Corp., Kyoto, Japan), ProMax(®) 3D (Planmeca, Helsinki, Finland) and NewTom VGi(®) (Quantitative Radiology, Verona, Italy). GafChromic XR-QA2 films were placed between the selected layers of the head and neck of a tissue-equivalent human skull (RANDO(®) phantom; The Phantom Laboratory, Salem, NY). The exposure parameters were set using the automatic exposure control function of the units. Depending on the availability, medium and smaller field of view (FOV) scanning modes were used. The effective dose was estimated using the 2007 International Commission on Radiological Protection formalism. RESULTS: The lowest effective dose of a CBCT unit was observed for ProMax 3D, FOV 4 × 5 cm (10 μSv), the highest for NewTom VGi, FOV 8 × 8 cm-high resolution (129 μSv). The range of effective doses for digital panoramic machines measured was 8-14 μSv. CONCLUSIONS: This study demonstrates the feasibility of using radiochromic films for dental CBCT and panoramic dosimetry.
| S-EPMC3699970 | biostudies-other
Project description:Dosimetry in kilovoltage cone beam computed tomography (CBCT) is a challenge due to the limitation of physical measurements. To address this, we used a Monte Carlo (MC) method to estimate the CT dose index (CTDI) and the dose length product (DLP) for a commercial CBCT system. As Dixon and Boone showed that CTDI concept can be applicable to both CBCT and conventional CT, we evaluated weighted CT dose index (CTDI(w)) and DLP for a commercial CBCT system. Two extended CT phantoms were created in our BEAMnrc/EGSnrc MC system. Before the simulations, the beam collimation of a Varian On-Board Imager (OBI) system was measured with radiochromic films (model: XR-QA). The MC model of the OBI X-ray tube, validated in a previous study, was used to acquire the phase space files of the full-fan and half-fan cone beams. Then, DOSXYZnrc user code simulated a total of 20 CBCT scans for the nominal beam widths from 1 cm to 10 cm. After the simulations, CBCT dose profiles at center and peripheral locations were extracted and integrated (dose profile integral, DPI) to calculate the CTDI per each beam width. The weighted cone-beam CTDI (CTDI(w,l)) was calculated from DPI values and mean CTDI(w,l) (CTDI(w,l)) and DLP were derived. We also evaluated the differences of CTDI(w) values between MC simulations and point dose measurements using standard CT phantoms. In results, it was found that CTDI(w,600) was 8.74 ± 0.01 cGy for head and CTDI(w,900) was 4.26 ± 0.01 cGy for body scan. The DLP was found to be proportional to the beam collimation. We also found that the point dose measurements with standard CT phantoms can estimate the CTDI within 3% difference compared to the full integrated CTDI from the MC method. This study showed the usability of CTDI as a dose index and DLP as a total dose descriptor in CBCT scans.
| S-EPMC5718669 | biostudies-literature
Project description:OBJECTIVES: In the 2011 project "Safety and efficacy of a new and emerging dental X-ray modality (SEDENTEXCT)", it was suggested that dose index (DI) and dose-area product (DAP) could be easily measured and used as diagnostic reference levels (DRLs), which would help in the management of radiation doses to patients in optimum exposure settings. Such indices could be directly related to effective dose. The purposes of this study, therefore, were to measure and calculate the DI and DAP in cone beam CT (CBCT) machines and to evaluate the correlation between the two. METHODS: Dose measurements were performed on three-dimensional cone beam CT (3D-CBCT) machines [3D Accuitomo (J. Morita Mfg. Corp., Kyoto, Japan), Veraviewepocs (J. Morita Mfg. Corp.) and CS9300 (Carestream, New York, NY)] by exposing a cylindrical poly-methyl methacrylate (PMMA) phantom using a CT ionization chamber. These dose measurements were used for the calculation of Dose Indices 1 and 2, according to the methodology suggested by SEDENTEXCT. The DAP was measured using a DAP meter that was attached to the detector to cover the entire irradiated area. RESULTS: The DI1 ranged from 53.6 mR to 216.6 mR, the DI2 ranged from 77.1 mR to 325.0 mR and the DAP ranged from 101.1 mGy cm(2) to 457.9 mGy cm(2), depending on the machines and exposure settings. Index 2 had a better correlation with the DAP than Index 1. CONCLUSIONS: The DIs and DAP proposed by SEDENTEXCT may be useful for establishing DRLs for dental CBCT machines; however, further studies are necessary to determine which of these indices provide accurate dose estimates proportionally relating to the effective dose.
| S-EPMC3635780 | biostudies-other
Project description:ObjectivesTo identify a dose as low as diagnostically acceptable and a threshold level of image quality for cone beam CT (CBCT) imaging root canals, using maxillary first molar (M1M) second mesiobuccal (MB2) canals of varying complexity for two CBCT scanners.MethodsDose-area product (DAP) and contrast-to-noise ratio (CNR) were measured for two scanners at a range of exposure parameters. Subjective-image-quality assessment at the same exposures was performed for three M1Ms of varying MB2 complexity, positioned in an anthropomorphic phantom. Nine raters (three endodontists, three dental radiologists and three junior staff) assessed canal visibility, using a 5-point confidence scale rating.ResultsIdentification of simple-moderate MB2 canal complexity was achieved at a range of protocols, with DAP values of ≥209.3 and ≥203.2 mGy cm² and CNRs of 3 and 7.6 for Promax®3D and Accuitomo-F170® respectively. For complex canal anatomy, target subjective image quality was not achieved, even at the highest DAP values for both scanners. Junior staff classified significantly more images as undiagnostic compared with senior staff (p = 0.043).ConclusionsIn this first study to address optimisation of CBCT imaging of root canal anatomy, a similar threshold dose for both scanners was identified for M1Ms with simple-moderate MB2 canal complexity. Increasing dose to enhance visualisation of more complex canal anatomy was ineffective. Selection of standard protocols (while avoiding lower kV/mA protocols) instead of high-resolution scans was a practical means of reducing patient dose. CNR is not a transferable measure of image quality.
| S-EPMC7549527 | biostudies-literature
Project description:Cone beam CT (CBCT) in image-guided radiotherapy (IGRT) offers a tremendous advantage for treatment guidance. The associated imaging dose is a clinical concern. One unique feature of CBCT-based IGRT is that the same patient is repeatedly scanned during a treatment course, and the contents of CBCT images at different fractions are similar. The authors propose a progressive dose control (PDC) scheme to utilize this temporal correlation for imaging dose reduction.A dynamic CBCT scan protocol, as opposed to the static one in the current clinical practice, is proposed to gradually reduce the imaging dose in each treatment fraction. The CBCT image from each fraction is processed by a prior-image based nonlocal means (PINLM) module to enhance its quality. The increasing amount of prior information from previous CBCT images prevents degradation of image quality due to the reduced imaging dose. Two proof-of-principle experiments have been conducted using measured phantom data and Monte Carlo simulated patient data with deformation.In the measured phantom case, utilizing a prior image acquired at 0.4 mAs, PINLM is able to improve the image quality of a CBCT acquired at 0.2 mAs by reducing the noise level from 34.95 to 12.45 HU. In the synthetic patient case, acceptable image quality is maintained at four consecutive fractions with gradually decreasing exposure levels of 0.4, 0.1, 0.07, and 0.05 mAs. When compared with the standard low-dose protocol of 0.4 mAs for each fraction, an overall imaging dose reduction of more than 60% is achieved.PINLM-PDC is able to reduce CBCT imaging dose in IGRT utilizing the temporal correlations among the sequence of CBCT images while maintaining the quality.
| S-EPMC3669143 | biostudies-other
Project description:PurposeTo provide initial assessment of image quality and dose for a cone-beam computed tomographic (CT) scanner dedicated to extremity imaging.Materials and methodsA prototype cone-beam CT scanner has been developed for imaging the extremities, including the weight-bearing lower extremities. Initial technical assessment included evaluation of radiation dose measured as a function of kilovolt peak and tube output (in milliampere seconds), contrast resolution assessed in terms of the signal difference-to-noise ratio (SDNR), spatial resolution semiquantitatively assessed by using a line-pair module from a phantom, and qualitative evaluation of cadaver images for potential diagnostic value and image artifacts by an expert CT observer (musculoskeletal radiologist).ResultsThe dose for a nominal scan protocol (80 kVp, 108 mAs) was 9 mGy (absolute dose measured at the center of a CT dose index phantom). SDNR was maximized with the 80-kVp scan technique, and contrast resolution was sufficient for visualization of muscle, fat, ligaments and/or tendons, cartilage joint space, and bone. Spatial resolution in the axial plane exceeded 15 line pairs per centimeter. Streaks associated with x-ray scatter (in thicker regions of the patient--eg, the knee), beam hardening (about cortical bone--eg, the femoral shaft), and cone-beam artifacts (at joint space surfaces oriented along the scanning plane--eg, the interphalangeal joints) presented a slight impediment to visualization. Cadaver images (elbow, hand, knee, and foot) demonstrated excellent visibility of bone detail and good soft-tissue visibility suitable to a broad spectrum of musculoskeletal indications.ConclusionA dedicated extremity cone-beam CT scanner capable of imaging upper and lower extremities (including weight-bearing examinations) provides sufficient image quality and favorable dose characteristics to warrant further evaluation for clinical use.
| S-EPMC4263642 | biostudies-literature
Project description:Background & purposeFour dimensional Cone beam CT (CBCT) has many potential benefits for radiotherapy but suffers from poor image quality, long acquisition times, and/or long reconstruction times. In this work we present a fast iterative reconstruction algorithm for 4D reconstruction of fast acquisition cone beam CT, as well as a new method for temporal regularization and compare to state of the art methods for 4D CBCT.Materials & methodsRegularization parameters for the iterative algorithms were found automatically via computer optimization on 60 s acquisitions using the XCAT phantom. Nineteen lung cancer patients were scanned with 60 s arcs using the onboard image on a Varian trilogy linear accelerator. Images were reconstructed using an accelerated ordered subset algorithm. A frequency based temporal regularization algorithm was developed and compared to the McKinnon-Bates algorithm, 4D total variation and prior images compressed sensing (PICCS).ResultsAll reconstructions were completed in 60 s or less. The proposed method provided a structural similarity of 0.915, compared with 0.786 for the classic McKinnon-bates method. For the patient study, it provided fewer image artefacts than PICCS, and better spatial resolution than 4D TV.ConclusionFour dimensional iterative CBCT reconstruction was done in less than 60 s, demonstrating the clinical feasibility. The frequency based method outperformed 4D total variation and PICCS on the simulated data, and for patients allowed for tumor location based on 60 s acquisitions, even for slowly breathing patients. It should thus be suitable for routine clinical use.
| S-EPMC7807579 | biostudies-literature
Project description:ObjectivesTo apply the ROBIS tool for assessment of risk of bias (RoB) in systematic reviews (SRs) in a meta-review on effective doses (EDs) in dental and maxillofacial cone beam CT.MethodsThree electronic databases and reference lists of included SRs were searched. Eligible SRs were classified as having low, high or unclear RoB. Findings of SRs were synthesised and data from primary studies combined to relate ED to field of view (FOV) and operating potential (kV).ResultsSeven SRs were included: three displayed low RoB, three high and one had unclear RoB. Only one SR related ED to image quality. Deficiencies in reporting of eligibility criteria, study selection and synthesis of results in SRs were identified. FOV height had a significant relationship with ED, explaining 27.2% of its variability. Median ED for three FOV categories differed significantly. Operating potential had a weak relationship with ED, with no significant difference in median ED between three operating potential groups.ConclusionThe ROBIS tool should have a role for meta-reviews of different aspects of radiology. The disappointing results for RoB might be remedied by developing standards to improve the quality of reporting of primary dosimetry studies and of SRs. Future dosimetry studies should always relate ED to image quality or diagnostic accuracy.Advances in knowledgeThis meta-review is the first to implement ROBIS for SRs of ED and identified that trustworthiness of some SRs is questionable. The percentage change in average ED per cm increase in FOV height could be calculated, emphasizing the importance of FOV as a determinant of ED in CBCT.
| S-EPMC8248222 | biostudies-literature